User manual

ManualsBrandsADJ ManualsLasers3in1 Lighting Effect

10/15

User Instructions

Stinger ii

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.adj.com / E-mail: info@americandj.com

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

The Netherlands

service@adjgroup.eu / www.adj.com

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

Please Note: Specications and improvements in the design

of this unit and this manual are subject to change without any

prior written notice.

Stinger II Specifications

Model: Stinger II

Voltage: 100V ~ 240V 50/60Hz

LED: 6 x 5W RGBAWP Hex LEDs

8 x 3W UV LEDs

Laser: 4.9mW Red & Green Laser Diodes

Power Draw: 70W

Fuse: 2A

Power Cord Daisy Chain: 10 Fixtures Max.

Dimensions: 12”(L) x 9”(W) x 9.75”(H)

304mm x 230.5mm x9.75mm

Weight: 11 lbs. / 5 kgs.

Colors: RGBAWP

Duty Cycle: None

DMX Channels: 2 DMX Modes: 2 & 9 Channels

Sound Active: Yes

Working Position: Any Safe, Secure Position

Warranty: 1 Year (365 Days)

Auto Sensing Voltage: This xture contains a automatic voltage

switch, which will auto sense the voltage when it is plugged into

the power source.

Summary of content (12 pages)

PAGE 1
Stinger II Specifications Model: Stinger II Voltage: 100V ~ 240V 50/60Hz LED: 6 x 5W RGBAWP Hex LEDs 8 x 3W UV LEDs Laser: 4.9mW Red & Green Laser Diodes Power Draw: 70W Fuse: 2A Power Cord Daisy Chain: 10 Fixtures Max. Dimensions: 12”(L) x 9”(W) x 9.75”(H) 304mm x 230.5mm x9.75mm Weight: 11 lbs. / 5 kgs.
PAGE 2
©2015 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted.
PAGE 3
Stinger II Fuse Replacement Disconnect the unit from its power source. Remove the power cord from the unit. Once the cord has been removed, you will find that the fuse holder is located inside the power socket. Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder also has a holder for a spare fuse.
PAGE 4
Stinger II General Instructions To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference.
PAGE 5
Stinger II Channel 1 Value 0-9 10 - 44 45 - 79 80 - 114 115 - 149 150 - 184 185 - 219 220 - 255 2 0 - 247 248 - 255 Stinger II Channel 1 2 3 Value 0-9 10 - 44 45 - 79 80 - 114 115 - 149 150 - 184 185 - 219 220 - 255 0-9 10 - 198 199 - 225 226 - 255 0-9 10 - 244 245 - 255 2 Channel Mode Function SHOW MODE NO FUNCTION SHOW 1 SHOW 2 SHOW 3 SHOW 4 SHOW 5 SHOW 6 RANDOM SHOW SHOW SPEED/SOUND SENSE SHOW SPEED SLOW - FAST SOUND ACTIVE 9 Channel Mode Function SHOW MODE NO FUNCTION SHOW 1 SHOW 2
PAGE 6
Stinger II Laser Warnings and Safety NON-INTERLOCKED HOUSING WARNING The Royal Sky contains high power laser devices internally. Do not open the laser housing, due to the potential exposure to unsafe levels of laser radiation. The laser power levels, if the unit is opened, can cause instant blindness, skin burns and fires.
PAGE 7
Stinger II Master-Slave Set Up Master-Slave Operation This function will allow you to link up to 16 units together and operate without a controller. In a Master-Slave set up, one unit will act as the controlling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave. 1. Using approved DMX data cables, daisy chain your units together via the XLR connector on the rear of the units.
PAGE 8
Stinger II Set Up Power Supply: The ADJ Stinger II contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere. DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers.
PAGE 9
Stinger II Stinger II System Menu Set Up POWER POWER Notice: Be sure to follow figures two and three when making your own DMX512 DISP - This function will reverse the display 180º. DMX+,DMX-,COMMON cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior. 1.
PAGE 10
Stinger II Set Up 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.
PAGE 11
Stinger II UVSP - UV activation/speed control. System Menu Stinger II Laser Warning Labels 1. Press the MENU button until “UVSP” is displayed, press ENTER. 2. The display will show either “FAST” or “SLOW”. Use the UP and DOWN buttons to highlight your selection. 3. Press ENTER to confirm. SLND - This will let you set unit as a master or slave in a master/slave configuration. 1. Press the MENU button until “SLND” is displayed, press ENTER. Either “MAST”, “SL 1”, or “SL 2” will be displayed.
PAGE 12
Stinger II System Menu Stinger II System Menu System Menu: When making adjustments press ENTER to confirm your setup then press and hold the MENU button for at least 3 seconds. To exit without making any adjustments press the MENU button. The display will lock after 30 seconds, press the MENU button for 3 seconds to unlock. ADDR - DMX Address Setting. 1. Press the either the MENU, UP, or DOWN buttons until “ADDR” is displayed, press ENTER. 2.