User manual

ManualsBrandsADJ ManualsLEDLED Bar Set

User Instructions

6/14

VBar Pak

VBar Pak Specifications

Model:

VBar Pak

Voltage: 100V ~ 240V/50~60Hz

LEDs: 5 x 4W 4-in-1 LED’s

Beam Angle: 40 Degrees

Working Position: Any safe working position

Power Draw: 21W

Power Cord Daisy Chain: 30 Fixtures Max.

Fuse: 2 Amp

Fixture Weight: 4 lbs./ 1.7Kgs.

System Weight: 9 lbs. / 4 Kgs.

Fixture Dimensions: 22” (L) x 2.5” (W) x 3.5” (H)

560 x 63 x 90mm

VBar Bag Dimensions: 22” (L) x 6.5” (W) x 3.5” (H)

560 x 165 x 90mm

Colors: RGBA Color Mixing

DMX Channels: 8 DMX Modes: 1 Channel Mode,

2 Channel Mode, 3 Channel Mode,

4 Channel Mode, 5 Channel Mode,

6 Channel Mode, 7 Channel Mode, &

8 Channel Mode

Warranty: 2 Year (730 days) Limited Warranty

ADJ Products, LLC

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.adj.com / E-mail: info@americandj.com

A.D.J. Supply Europe B.V.

Junostraat 2

6468 EW Kerkrade

Netherlands

service@adjgroup.eu / www.adj.com

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

Please Note: Specications and improvements in the design of this

unit and this manual are subject to change without any prior written

notice.

Auto Sensing Voltage: This xture contains a automatic voltage

switch, which will auto sense the voltage when it is plugged into the

power source.

Summary of content (12 pages)

PAGE 1
VBar Pak Specifications Model: VBar Pak Voltage: 100V ~ 240V/50~60Hz LEDs: 5 x 4W 4-in-1 LED’s Beam Angle: 40 Degrees Working Position: Any safe working position Power Draw: 21W Power Cord Daisy Chain: 30 Fixtures Max. Fuse: 2 Amp Fixture Weight: 4 lbs./ 1.7Kgs. System Weight: 9 lbs. / 4 Kgs. Fixture Dimensions: 22” (L) x 2.5” (W) x 3.5” (H) 560 x 63 x 90mm VBar Bag Dimensions: 22” (L) x 6.5” (W) x 3.
PAGE 2
©2013 ADJ Products, LLC all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted.
PAGE 3
VBar Pak Power Cord Daisy Chain With this feature you can connect the fixtures to one another using the IEC input and output sockets. The quantity that can be connected is 30 fixtures maximum. After 30 fixtures you will need to use a new power outlet. They must be the same fixtures. DO NOT mix fixtures. VBar Pak Fuse Replacement Disconnect the unit from its power source. Remove the power cord from the unit.
PAGE 4
VBar Pak Features • • • • • • • Mulit-Colors Five Operating Modes Electronic Dimming 0-100% Built in Microphone DMX-512 protocol 3-Pin DMX Connection Eight DMX Modes: 1 Channel Mode, 2 Channel Mode, 3 Channel Mode, 4 Channel Mode, 5 Channel Mode, 6 Channel Mode, 7 Channel Mode, & 8 Channel Mode • ADJ LED RC2 Included • Power Cord Daisy Chain (See page 21) VBar Pak Warranty Registration The VBar Pak carries a 2 year limited warranty.
PAGE 5
VBar Pak Channel 8 8 Channel Mode Value Function 64 - 79 80 - 95 96 - 111 112 - 127 128 - 143 144 - 159 160 - 175 176 - 191 192 - 207 208 - 223 224 - 239 240 - 255 COLOR CHANGE MODE CONT.
PAGE 6
VBar Pak Set Up Power Supply: The ADJ VBar contains a automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere. DMX-512: DMX is short for Digital Multiplex. This is a universal pro- tocol used as a form of communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture.
PAGE 7
POWER VBar Pak Channel 6 Channel Mode Value VBar Pak Function RED 0 - 255 0% - 100% 2 GREEN 0 - 255 0% - 100% 3 BLUE 0 - 255 0% - 100% 4 AMBER 0 - 255 0% - 100% 5 MASTER DIMMER 0 - 255 0% - 100% 6 COLOR MACROS 0 - 255 PLEASE SEE 1 CHANNEL MODE Channels 1, 2, & 3 will not work, when Channel 6 is being used.
PAGE 8
VBar Pak Operating Instructions LED Display On/Off: To set the LED display to turn off after 10 seconds, press the MODE button until “dxx” is displayed. “XX” represents either “on” or “oFF”. Press the UP or DONW buttons so that “doff” is displayed. Now the display will disappear after 10s. Press any button to turn the display on again. Be advised though that the display will turn off automatically after 10 seconds. “don” = LED display on at all times. “doFF” = LED display shuts off after 10 seconds.
PAGE 9
VBar Pak Channel 1 VBar Pak Channel 1 VBar Pak Channel 1 2 3 Value Function 0 - 15 16 - 31 32 - 47 48 - 63 64 - 79 80 - 95 96 - 111 112 - 127 128 - 143 144 - 159 160 - 175 176 - 191 192 - 207 208 - 223 224 - 239 240 - 255 COLOR MACROS OFF RED GREEN BLUE AMBER RED & GREEN RED & BLUE RED & AMBER GREEN & BLUE GREEN & AMBER BLUE & AMBER RED & GREEN & BLUE RED & GREEN & AMBER RED & BLUE & AMBER GREEN & BLUE & AMBER RED & GREEN & BLUE & AMBER Value 0 - 255 2 1 Channel Mode 0 - 255 0 - 255 0 - 15
PAGE 10
VBar Pak Operating Instructions you can then activate strobing by pressing the SET UP button to enter the Flash (strobe) mode. 7. “FS.XX” will be displayed, this is Flash mode. The Flash can be adjusted between “FS.00” (flash off) to “FS.15” (fastest flash). Sound Active Mode: In this mode the VBar will react to sound, and chase through the different colors. 1. Plug the fixture in and press the MODE button until “SoXX” is displayed. “XX” represents the sound active mode (1-16) currently displayed.
PAGE 11
VBar Pak ADJ LED RC2 DMX MODE - This button will let you select which DMX mode you want to use. Some fixtures will come with different DMX channel modes. Press the “+” & “-” buttons to switch DMX channel modes Please see pages 15-20 for DMX modes, values, and traits. • If the Red LED’s glow you are in DMX Mode 1: 1 Channel Mode. • If the Green LED’s glow you are in DMX Mode 2: 2 Channel Mode. • If the Blue LED’s glow you are in DMX Mode 3: 3 Channel Mode.
PAGE 12
VBar Pak Master-Slave Configuration Master-Slave Operation: This function will allows you to link units together to run in a Master-Slave configuration. In a Master-Slave configuration one unit will act as the controlling unit and the others will react and copy the controlling units operation. Any unit can act as a Master or as a Slave however, only one unit can be programmed to act as the “Master.” Master-Slave Connections and Settings: 1.