Instruction manual

ManualsBrandsADJ ManualsDJ EquipmentX-move LED plus

American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 2

X-Move LED Plus R General Information

Unpacking: Thank you for purchasing the X-Move LED Plus R by

American DJ®. Every X-Move LED Plus R has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check

the shipping carton for damage that may have occurred during ship-

ping. If the carton appears to be damaged, carefully inspect your x-

ture for any damage and be sure all equipment necessary to operate

the unit has arrived intact. In the event damage has been found or parts

are missing, please contact our toll free customer support number for

further instructions. Please do not return this unit to your dealer with-

out contacting customer support rst.

Introduction: The X-Move LED Plus R is a nine channel DMX intel-

ligent, moving head, mini LED fixture. The X-Move LED Plus R can

operate as a stand alone fixture or in a Master/Slave configuration.

The X-Move LED Plus R has three operating modes; a sound active,

show mode, DMX controlled. For best results use fog or special effects

smoke to enhance the beams projections.

Customer Support: American DJ® provides a toll free customer

support line, to provide help and to answer any question should you

encounter problems during your set up or initial operation. You may

also visit us on the web at www.americandj.com for any comments or

suggestions. Service Hours are Monday through Friday 9:00 a.m. to

4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: support@americandj.com

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or re, do

not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly

into the light source at all times!

User Instructions

Rev. 2/11

Summary of content (12 pages)

PAGE 1
X-Move LED Plus R General Information Unpacking: Thank you for purchasing the X-Move LED Plus R by American DJ®. Every X-Move LED Plus R has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact.
PAGE 2
X-Move LED Plus R General Instructions To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference.
PAGE 3
X-Move LED Plus R Set Up X-Move LED Plus R Power Supply: Before plugging your unit in, be sure the source volt- INPUT OUTPUT 1 2 3 American DJ® - www.americandj.com - X-Move LED Plus R Instruction Manual Page 5 Set Up INPUT OUTPUT SOUN POWER DMX+,DMX-,COMMON cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing.
PAGE 4
X-Move LED Plus R Set Up X-Move LED Plus R System Menu 5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX- 512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.
PAGE 5
X-Move LED Plus R System Menu System Menu: When making adjustments you can press ENTER to confirm your setup or you can wait 8 seconds for automatic setup. To exit without making any adjustments press the MENU button. X-Move LED Plus R System Menu SLND - This will let you set unit as a master or slave in a master/slave configuration. ADDR - DMX Address Setting. 1. Tap the MENU button until “SLND” is displayed, press ENTER. Either “SL 1” or “SL 2” will be displayed. 1.
PAGE 6
X-Move LED Plus R System Menu 2. To activate the Pan inversion tap the UP or DOWN buttons until I is displayed, press ENTER to confim. To deactivate Pan inversion, select No and press Enter. I TLT - Tilt Inversion 1. Tap the MENU button until “I TLT” is displayed, press ENTER. Either NO or 1 will be displayed. 2. To activate the Tilt inversion tap the UP or DOWN buttons until I is displayed, press ENTER to confim. To deactivate Tilt inversion, select No and press Enter.
PAGE 7
X-Move LED Plus R System Menu tures home position. 1. Press the ENTER button for at least 5 seconds to enter into offset mode. 2. Press the UP or DOWN buttons until “OTIL” is displayed, and press ENTER. The display will begin to flash. 3. Press the UP or DOWN buttons to adjust to your desired home position. Once you have found your desired position press the ENTER button to set and save, or press the MENU button to return to return to offset functions without any changes.
PAGE 8
X-Move LED Plus R Operation traits. 2. To control your fixture in DMX mode, follow the set-up procedures on pages 5-7 as well as the set-up specifications that are included with your DMX controller. 3. Use the controller’s faders to control the various DMX fixture traits. 4. This will allow you to create your own programs. 5. Follow the instruction on page 9 to set the DMX address. 6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture. 7.
PAGE 9
X-Move LED Plus R Channel Value 6 7 8 9 0-7 8 - 15 16 - 131 132 - 139 140 - 180 181 - 190 191 - 231 232 - 239 240 - 247 248 - 255 0 - 255 0-7 8 - 28 29 - 49 50 - 70 71 - 91 92 - 112 113 - 133 134 - 154 155 - 175 176 - 196 197 - 217 218 - 238 239 - 255 0 - 255 DMX Traits Function SHUTTER/STROBE BLACKOUT SHUTTER OPEN STROBING SLOW - FAST SHUTTER OPEN SHUTTER SLOW OPEN - FAST CLOSE SHUTTER OPEN SHUTTER FAST OPEN - SLOW CLOSE SHUTTER OPEN RANDOM STROBE SHUTTER OPEN DIMMER 0% - 100% MOVING HEAD MOV
PAGE 10
X-Move LED Plus R Gobo Replacement X-Move LED Plus R Fuse Replacement Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder located inside the power socket. Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one. The fuse holder has a built-in socket for a spare fuse be sure not to confuse the spare fuse with active fuse.
PAGE 11
X-Move LED Plus R Warranty X-Move LED Plus R Notes MANUFACTURER’S LIMITED WARRANTY A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American Audio products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories.
PAGE 12
X-Move LED Plus R Model: Voltage*: LED: Power Consumption: Dimensions: Beam Angle: Colors: Weight: Fuse: Duty Cycle: DMX: Colors: Gobos: Sound Active: Working Position: Warranty: Specifications X-Move LED Plus R 120v/60Hz or 230v/50Hz 1x10W LED 60W 8”(L) x 7.5”(W) x 12.5”(H) 205mm x 190mm x 320mm 14 Degree RGB + White 13 Lbs. / 5.9 kgs. 2 Amp None 9 DMX Channels 8 + White 6 + Spot 23.8mm/0.