Instruction manual

- DA321G5321
- 53 -
6.28.5 Light barrier filter for knitted fabrics
Function with or without control panel
Parameter
Number of stitches of the light barrier filter
Light barrier filter On/Off
Light barrier sensing uncovered or covered
(LSF)
(LSF)
(LSd)
005
130
131
The filter prevents premature enabling of the light barrier function when sewing knitted fabrics.
 Enabling/Disabling of the filter using parameter 130
 The filter is not active if parameter 005 = 0
 Adaptation to the mesh is possible by varying the number of filter stitches.
 Knitted fabrics sensing for light barrier detection light  dark if parameter 131 = 0
Knitted fabrics sensing for light barrier detection dark  light if parameter 131 = 1
6.29 Switching function of inputs in2, in3, in5, in6, in8, in9 and i10
Function with or without control panel
Parameter
Selection of the input function
241...249
With parameters 241, 242, 244, 245, 247, 248 and 249 for inputs in2, in3, in5, in6, in8, in9, and in10, the
function of keys/switches connected to plug connectors ST2 and B4 can be selected.
Parameter 241, 242, 244, 245, 247, 248, 249 =:
0 Input function blocked
1 Needle up/down:
Upon pressing the key, the drive runs from position 1 to the return position. This is independent of whether
the return is turned on or off. If parameter 180 has a value of 0, the drive stops in position 2. If the drive is
outside the slot of position 1, no movement is carried out for safety reasons. After power--on, the function is
blocked until sewing starts.
2 Needle up
Upon pressing the key, the drive runs from position 1 to the return position. This is independent of whether
the return is turned on or off. If parameter 180 has a value of 0, the drive stops in position 2. If the drive is
outside the slot of position 1, no movement is carried out for safety reasons. After power--on, the function is
blocked until sewing starts.
3 Single stitch (basting stitch):
Upon pressing the key, the drive performs one rotation from position 1 to position 1 If the drive is in the
return position, it runs to position 1 upon pressing the key and from position 1 to position 1 each time the
key is pressed again.
4 Full stitch:
Upon pressing the key, the drive performs a full rotation depending on the set stop position.
5 Needle to position 2:
When the key is pressed, the drive runs regardless of its position into position 2 or the return position. This
function is also possible after power-on.-
6 Machine run blockage effective with open contact:
Upon opening the switch, the drive stops in the pre-selected basic position.
7 Machine run blockage effective with closed contact:
Upon opening the switch, the drive stops in the pre-selected basic position.
8 Machine run blockage effective with open contact (unpositioned):
Upon opening the switch, the drive stops immediately unpositioned..
9 Machine run blockage effective with closed contact (unpositioned):
Upon closing the switch, the drive stops immediately unpositioned.
10 Run at automatic speed (n12):
Upon pressing the key, the drive runs at automatic speed. The pedal is not used.
11 Run at limited speed (n12):
Upon pressing the key, the drive runs at limited speed. The pedal must be pressed forward.
12 Sewing foot lifting with pedal in position 0 (neutral)
13 High Lift for Walking Foot Operational Mode Not Stored :
The signal “high lift for walking foot” is issued as long as the key is held down, and the drive runs with
speed limitation (n10).
14 high lift for walking foot ratcheting:
The signal “high lift for walking foot” is issued upon briefly pressing the key, and the drive runs with speed
limitation (n10). The operation is disabled upon pressing the key again.
15 Sewing foot pressure