cPCIS-1100 Series 3U Height Subsystems for CompactPCI Modules User’s Manual Manual Rev.: Date: Part Number: 2.
Revision History Revision 2.00 Release Date September 15, 2014 Description of Change(s) Initial release Copyright 2014 ADLINK Technology, Inc. All Rights Reserved. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.
Table of Contents 1 Introduction ....................................................................................1 1.1 1.2 1.3 1.4 2 Product Definition ......................................................................1 Mechanical Drawing ..................................................................2 Configurations............................................................................3 Customized Systems .................................................................
.2 4.3 5 CompactPCI: cPS-H325/AC....................................................35 Features .............................................................................35 Specifications .....................................................................35 Input Characteristics...........................................................35 Output Characteristics ........................................................36 CompactPCI ETT PSU: cPS-P325/AC....................................37 Features .
1 Introduction 1.1 Product Definition The cPCIS-1100 Series Subsystems are rack mountable, 3U in height, and designed for 3U CompactPCI cards and modules. They are ideal for industrial or transport applications where small chassis size with multifunctionality are important, and provide ample power capacity, a hot swap backplane and easy maintenance.
1.
1.3 Configurations The cPCI-1100 Series comes in the following configurations: System Slots Peripheral Slots PSU(s) Monitor PICMG cPCIS-1100A[R] 1 7 400W ATX — 2.0, 2.1 cPCIS-1101[R] 1 7 250W cPCI — 2.0, 2.1, 2.11 cPCIS-1102[R] 1 7 250W cPCI (1+1) — 2.0, 2.1, 2.11 cPCIS-1202[R] (dual system) 1x2 5x2 250W cPCI (1 / 1) — 2.0, 2.1, 2.11 cPCIS-ET1101 1 7 250W ETT cPCI PSU — 2.0,2.1 2.11 cPCIS-ET1102 1 7 250W ETT 2 x cPCI PSU — 2.0, 2.1, 2.
This page intentionally left blank.
2 Getting Started In this chapter, we will describe the unpacking procedure of the sub-system and CompactPCI board and power supply unit (PSU) installation procedures for cPCIS-1100 Series models with CompactPCI PSU(s) only. 2.1 Shipping Contents Check the shipping carton for any damage. If the shipping carton and contents are damaged, please notify the dealer for a replacement. Retain the shipping carton and packing material for inspection by the dealer.
PSU Slot System slots have obvious indicators (e.g. red card guide rail, triangle mark enclosing the slot number on the backplane, etc.) System cards can only be installed in a system slot. Do not insert a system card into any other slot, or insert any peripheral card into system slot. System Card Slot Peripheral Card Slots The handle on CompactPCI cards and PSUs ensures simple and safe installation and removal.
CompactPCI Card Installation/Removal Procedure 1. Place the sub-system on a level surface or rackmount it. Remove the blanking plates where required by undoing the retaining screws at each end. Retain the blanking plates for possible future use. The system should not be put into use without blanking plates for all empty slots, otherwise the EMC will be compromised 2. Hold the SBC module, peripheral card or PSU module vertically. For PSU modules, make sure that the handle is unlatched (i.e.
Fully Latched Handle Engages with Chassis System Card Fully Inserted To remove the module, press the release button (if necessary), and reverse steps 1 through 5 above. 2.
The installation and removal procedures for a RTM are the same as those for CompactPCI boards. Because they are shorter than front boards, pay careful attention when inserting or removing RTMs. Only models with an “R” at the end of the model number support RTMs. Note: We strongly recommended the use of RTMs with AB type connectors to prevent damaging the backplane during RTM installation. 2.4 Powering Up the System Connect the supplied power cord to the socket on the back of the chassis.
This page intentionally left blank.
3 Backplane In this chapter, we will describe the backplanes for the cPCIS-1100 Series subsystems. The following table specifies the backplane(s) that correspond to each model. 3.
Peripheral slots: 7 Peripheral Slots Rear I/O: P2 rear I/O with AB-type shroud (optional) Power Connectors: ATX connector x2, DC screw terminals V (I/O): 3.
1 - P2 Optional Rear I/O: 2 - P2 to 8 - P2 cBP-3208[R] Rear View Backplane • 13
Pin Assignment ¾ Pin [1 – P1] System Slot 25 Z GND 24 GND 23 GND 22 GND 21 20 A +5V B REQ64# C ENUM# D +3.3V E +5V F GND AD[1] +5V V(I/O) AD[0] ACK64# GND +3.3V AD[4] AD[3] +5V AD[2] GND AD[7] GND +3.3V AD[6] AD[5] GND GND +3.3V AD[9] AD[8] M66EN C/BE[0]# GND GND AD[12] GND V(I/O) AD[11] AD[10] GND 19 GND +3.3V AD[15] AD[14] GND AD[13] GND 18 GND SERR# GND +3.3V 17 GND +3.3V 16 GND DEVSEL# GND 15 GND +3.
¾ [1 – P2] System Slot Pin 22 21 20 19 18 17 16 15 14 13 12 Z GND GND GND GND GND GND GND GND GND GND GND A GA4 CLK6 CLK5 GND NC NC NC NC NC NC NC B GA3 GND GND GND NC NC NC NC NC NC NC C GA2 NC NC NC NC PRST# DEG# FAL# NC NC NC D GA1 NC NC NC NC REQ6# NC REQ5# NC NC NC E GA0 NC NC NC NC GNT6# NC GNT5# NC NC NC F GND GND GND GND GND GND GND GND GND GND GND 11 GND NC NC NC NC NC GND 10 9 8 7 6 5 4 3 2 1 Pin GND GND GND GND GND GND GND GND GND GND Z NC NC NC NC NC NC V(I/O) CLK4 CLK2 CLK1
¾ [2 – P1] / [8 – P1] Peripheral Slot Pin Z A B C D 25 24 GND +5V REQ64# ENUM# GND AD[1] +5V V(I/O) 23 GND +3.3V AD[4] AD[3] 22 GND AD[7] GND +3.3V AD[6] AD[5] GND 21 GND +3.3V AD[9] AD[8] M66EN C/BE[0]# GND 20 GND AD[12] GND V(I/O) AD[11] AD[10] GND 19 GND +3.3V AD[15] AD[14] GND AD[13] GND 18 GND SERR# GND +3.3V PAR C/BE[1]# GND 17 GND +3.3V GND PERR# GND 16 GND DEVSEL# GND V(I/O) STOP# LOCK# GND 15 GND +3.
¾ ¾ CN1 / CN2 – ATX Power Connector Pin Signal 11 1 1 +3.3V 2 +3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 POWER GOOD 9 5V STB 10 +12V Pin # 1 2 Signal Name +12V -12V Sense Pin # 1 2 Signal Name INH# GND Pin # 1 2 Signal Name PRST# GND Pin # 1 2 Signal Name FAL# GND JP10 – connector 1 ¾ +5V +5V JP9 – connector 1 ¾ 19 20 JP8 – connector 1 ¾ Signal +3.
3.2 cBP-3206[R] Backplane The cBP-3206[R] is a 3U CompactPCI 32-bit backplane with optional rear I/O (designated by an “R” suffix). The cPCIS-1202[R] uses two of these backplanes. Specifications Standard CompactPCI height for 3U cPCI cards CompactPCI Compliancy PICMG 2.0 CompactPCI core specification R3.0 PICMG 2.1 CompactPCI hot swap R2.0 Dimensions: 100.7 x 128.
Mechanical Drawing 6 - P2 1 - P2 6 - P1 1 - P1 cBP-3206[R] Front View JP8 - JP10 1 - P2 CN1 Opt.
Pin Assignment ¾ Pin [1 – P1] System Slot 25 Z GND 24 GND 23 GND 22 GND 21 20 A +5V B REQ64# C ENUM# D +3.3V E +5V F GND AD[1] +5V V(I/O) AD[0] ACK64# GND +3.3V AD[4] AD[3] +5V AD[2] GND AD[7] GND +3.3V AD[6] AD[5] GND GND +3.3V AD[9] AD[8] M66EN C/BE[0]# GND GND AD[12] GND V(I/O) AD[11] AD[10] GND 19 GND +3.3V AD[15] AD[14] GND AD[13] GND 18 GND SERR# GND +3.3V 17 GND +3.3V 16 GND DEVSEL# GND 15 GND +3.
¾ [1 – P2] System Slot Pin 22 21 20 19 18 17 16 15 14 13 12 Z GND GND GND GND GND GND GND GND GND GND GND A GA4 CLK6 CLK5 GND NC NC NC NC NC NC NC B GA3 GND GND GND NC NC NC NC NC NC NC C GA2 NC NC NC NC PRST# DEG# FAL# NC NC NC D GA1 NC NC NC NC REQ6# NC REQ5# NC NC NC E GA0 NC NC NC NC GNT6# NC GNT5# NC NC NC F GND GND GND GND GND GND GND GND GND GND GND 11 GND NC NC NC NC NC GND 10 9 8 7 6 5 4 3 2 1 Pin GND GND GND GND GND GND GND GND GND GND Z NC NC NC NC NC NC V(I/O) CLK4 CLK2 CLK1
¾ [2 – P1] – [6 – P1] Peripheral Slot Pin Z A B C D 25 24 GND +5V REQ64# ENUM# GND AD[1] +5V V(I/O) 23 GND +3.3V AD[4] AD[3] 22 GND AD[7] GND +3.3V AD[6] AD[5] GND 21 GND +3.3V AD[9] AD[8] M66EN C/BE[0]# GND 20 GND AD[12] GND V(I/O) AD[11] AD[10] GND 19 GND +3.3V AD[15] AD[14] GND AD[13] GND 18 GND SERR# GND +3.3V PAR C/BE[1]# GND 17 GND +3.3V GND PERR# GND 16 GND DEVSEL# GND V(I/O) STOP# LOCK# GND 15 GND +3.
¾ ¾ CN1 / CN2 – ATX Power Connector Pin Signal Pin 11 1 1 +3.3V 11 2 +3.3V 12 3 GND 13 4 +5V 14 5 GND 15 6 +5V 16 7 GND 17 8 POWER 18 GOOD 9 5V STB 19 10 +12V 20 Pin # 1 2 Signal Name INH# -12V Sense Pin # 1 2 Signal Name PRST# GND Pin # 1 2 Signal Name FAL# GND JP9 – connector 1 ¾ +5V +5V JP8 – connector 1 ¾ Signal +3.
3.3 cBP-3061 Power Backplane The cBP-3061 is a PICMG 2.11 CompactPCI 3U 47-pin power backplane for one power module. It is used by the cPCIS-11011/cPCIS-1202[R]/cPCISET1101/cPCIS-1202. Specifications CompactPCI Compliancy: PICMG 2.11 CompactPCI Power Interface Dimensions: 39.64x 128.
Pin Assignment ¾ CN1 – Power Sense Connector Pin # Signal Name 1 V1_Sense 2 GND_S 3 V2_Sense 4 V3_Sense 5 NC 1 ¾ CN2 – Power Sense Connector Pin # Signal Name 1 V1_Sense 2 GND_S 3 V2_Sense 4 V3_Sense 5 NC 1 ¾ CN3 – connector 1 Pin # 1 2 Signal Name INHJ GND Backplane • 25
¾ CN4 – Modular Power 47P Connector Pin Signal 47 ACL/-DC IN 47 46 ACN/+DC IN 45 CGND 44 V3 SHARE 44 42 43 IPMB_PWR 42 +FAL# 41 V2 SHARE 40 IPMB_SDA 23 21 39 INH# 20 19 38 DEG# 37 IPMB_SCL 36 V3 SENSE 35 V1 SHARE 34 S RTN 33 V2 SENSE 32 V2ADJ 2 ¾ 1 CN5 – Current Share Connector Pin # Signal Name 1 V1_Share 2 GND 3 V2_Share 4 V3_Share 5 NC 1 ¾ CN6 – Current Share Connector Pin # Signal Name 1 V1_Share 2 GND 3 V2_Share 4 V3_Share 5 NC 1 26 • Backplane Pin 31 30 29 28 27 26 25 24 23 22 21 20 19 13-18 5
¾ CN7 –AC/DC in Let Connector Pin # Signal Name 1 1 ACN/DC+ 2 ACL/DC3 CGND ¾ CN8 – IPMB Connector Pin # 1 1 2 3 4 5 ¾ Signal Name IPMB_SCL GND IPMB_SDA IPMB_PWR ALERT CN9 – ATX Power Connector Pin Signal 11 1 1 +3.3V 2 +3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 POWER GOOD 9 5V STB 10 +12V Pin 11 12 13 14 15 16 17 18 Signal +3.
3.4 cBP-3062A Power Backplane The cBP-3062A is a PICMG 2.11 CompactPCI 3U 47-pin power backplane for two power modules. It is used by the cPCIS-1102[R]/cPCIS-ET1102. Specifications CompactPCI Compliancy: PICMG 2.11 CompactPCI Power Interface Dimensions: 80.28 x 128.
Pin Assignment ¾ CN1 / CN2 – Modular Power 47P Connector Pin Signal Pin 47 ACL/-DC IN 31 47 46 ACN/+DC IN 30 45 CGND 29 44 V3 SHARE 28 44 4 43 IPMB_PWR 27 2 42 +FAL# 26 41 V2 SHARE 25 40 IPMB_SDA 24 23 21 39 INH# 23 20 19 38 DEG# 22 37 IPMB_SCL 21 36 V3 SENSE 20 35 V1 SHARE 19 34 S RTN 13-18 33 V2 SENSE 5-12 32 V2ADJ 1-4 Signal GA2 V1 SENSE V1ADJ GA1 EN# RESERVED GA0 RTN RESERVED RTN V4 V3 RTN V2 RTN V1 1 2 ¾ CN3 –AC/DC in Let Connector Pin # Signal Name 1 1 ACN/DC+ 2 ACL/DC3 CGND ¾ CN4 – Power Sens
¾ CN5 – Power Sense Connector Pin # Signal Name 1 V1_Sense 2 GND_S 3 V2_Sense 4 V3_Sense 5 NC 1 ¾ CN6 –Connector Pin # 1 2 3 4 5 1 ¾ Signal Name IPMB_SCL GND IPMB_DA IPMB_PWR ALERT CN7 – Current Share Connector Pin # Signal Name 1 V1CS 2 GND_S 3 V2 CS 4 V3 CS 5 NC 1 ¾ CN8 – Current Share Connector Pin # Signal Name 1 V1 CS 2 GND_S 3 V2 CS 4 V3 CS 5 NC 1 30 • Backplane
¾ ¾ CN9 / CN10 – ATX Power Connector Pin Signal 11 1 1 +3.3V 2 +3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 POWER GOOD 9 5V STB 10 +12V +5V +5V Pin # 1 2 Signal Name INH#2 GND Pin # 1 2 Signal Name INH#1 GND Pin # 1 2 3 4 5 6 7 8 Signal Name DEG#1 FAL#1 RSV23A RSV26A DEG#2 FAL#2 RSV23B RSV26B Pin # 1 2 Signal Name INH# GND JP3 – connector 1 8 ¾ 19 20 JP2 – connector 1 ¾ Signal +3.
This page intentionally left blank.
4 Power Supply Units The cPCIS-1100 Series subsystems are equipped with either the Zippy Technology Corp. PS2 HG2-6400P industrial grade ATX power supply, ADLINK’s cPS-H325/AC CompactPCI power module or ADLINK’s cPS-P325/AC wide range temperature operating CompactPCI power module (see Section 1.3 Configurations). 4.1 ATX: Zippy PS2 HG2-6400P Features • Active PFC (full range) • 12V Max.
Input Characteristics • Voltage: 90 – 240 VAC Full Range • Frequency : 47 ~ 63 HZ • Input Current: • Inrush Current: 65A MAX. FOR 115 VAC 125A MAX. FOR 230 VAC 8.0 A ( RMS ) FOR 115 VAC 4.0 A ( RMS ) FOR 230 VAC Output Characteristics Output Current(A) Regulation Output Output Voltage MIN. MAX. PEAK LOAD LINE Ripple& Noise Max[P-P] 5V 3 35 – ± 5% ± 1% 50mV 12V 2 30 – +7 – -5% ± 1% 120mV -5V 0 0.5 – ± 5% ± 1% 150mV -12V 0 0.8 – ± 5% ± 1% 150mV 3.
4.2 CompactPCI: cPS-H325/AC Features • 250W 3U x 8HP Eurocard package • Meets IEC1000-3-2 harmonic correction • Internal OR-ing diodes for N+1 redundancy • Hot-swappable • Third-wire current sharing • EMI meets EN 55022 / FCC CLASS A • CE marking compliance • Fully compliant with PICMG Specifications • Operating Temperature Range: 0 °C to 50°C • Storage Temperature: -40 to +85 °C • Temperature Coefficient: Typ. ±0.
• Dielectric Withstand: Meets IEC950 regulation • EMI: Meets EN55022 / FCC Class A • Hold-up Time: 5mS after power fail signal • Remote ON/OFF: Available at [INH#] & [EN#] pins • Power Fail Signal: Available at [FAL#] pin • Status LED: means valid input voltage; means a critical fault. • Thermal Protection (OTP): Installed NTC and thermostat for thermal sensor at [DEG#] pin • Power OK: Installed at all outputs • Leakage Current: Typ. 0.
4.3 CompactPCI ETT PSU: cPS-P325/AC Features • 250W 3U x 8HP Eurocard package • Meets EN 61000-3-2 active power factor correction • Internal OR-ing diodes for N+1 redundancy • Hot-swappable • Active current sharing • EMI meets EN 55022 / FCC CLASS A • CE marking compliance • Fully compliant with PICMG Specifications • Operating Temperature Range: -25°C to +50°C • Storage Temperature: -40 to +85 °C • Temperature Coefficient: Typ. ±0.
• Power Fail Signal: available at [FAL#] pin • Status LED: means valid input voltage; means a critical fault. • Thermal Protection (OTP): Installed NTC and thermostat for thermal sensor at [DEG#] pin • Power OK: Installed at all outputs • Leakage Current: 1.18mA at 254Vac/60Hz Output Characteristics Output Current (A) Output Voltage 5V 3.3V 12V -12V Min. Max. Typ. Peak. 0 40.0 25.0 – 0 40 20 – 0 5.
o o Over Current Protection: Installed at each rail. Overload Protection: Fully protected against output overload or short circuit. Typical 120% max. load.
This page intentionally left blank.
5 5.1 Specifications Features Standard 19” Rack-mount 3U CompactPCI form factor (3U height). Board Space: Supports both front and rear access for I/O, CPU, and power supply. Standard 3U, 21-slot width chassis. Suitable for rack-mount. Comprehensive EMC shielding [EMC gaskets are installed on front rails (top and bottom), rear rails, and side panels]. Power switch. At least 400 LFM external cooling fans are required 5.2 Mechanical CompactPCI Standard: 2.0 R3.
5.3 Environmental Operating Temperature: 1. cPS-H325/AC: 0°C ~ +50°C ; 2. cPS-P325/AC: -25°C ~ +50°C (Up to 70°C but will have derating issue when above 50°C. Power efficiency will be derating 2.5% every Celsius degree and it will only have 50% of power efficiency when 70°C.) Storage Temperature: -40°C to +85°C. Humidity: 5% - 95%, non-condensed. Shock: 15G peak-to-peak, 11ms duration, non-operation. Vibration: o Non-operation:1.88Grms, 5 – 500Hz, each axis. Operation: 0.5Grms, 5 – 500Hz, each axis.
Important Safety Instructions Read and follow all instructions marked on the product and in the documentation before you operate your system. Retain all safety and operating instructions for future use. z Please read these safety instructions carefully. z Please keep this User‘s Manual for later reference. z The equipment can be operated at an ambient temperature of 50ºC. z The equipment should be operated only from the type of power source indicated on the rating label.
If one of the following situations arises, get the equipment checked by a service personnel: A. The power cord or plug is damaged. B. Liquid has penetrated into the equipment. C. The equipment has been exposed to moisture. D. The equipment has not work well or you can not get it work according to user‘s manual. E. The equipment has dropped and damaged. F. If the equipment has obvious sign of breakage.
