IMB-M40H ATX Intel® Core™ i7/i5/i3 Industrial Motherboard User’s Manual Manual Rev.: 1.00 Revision Date: July 31, 2013 Part No: 50-1X005-1000 Advance Technologies; Automate the World.
Revision History ii Revision Release Date 1.
IMB-M40H Preface Copyright 2013 ADLINK Technology, Inc. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
Using this Manual Audience and Scope The IMB-M40H User’s Manual is intended for hardware technicians and systems operators with knowledge of installing, configuring and operating industrial grade systems. Manual Organization This manual is organized as follows: Preface: Presents important copyright notifications, disclaimers, trademarks, and associated information on the proper understanding and usage of this document and its associated product(s).
IMB-M40H Conventions Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly. Additional information, aids, and tips that help users perform tasks. NOTE: CAUTION: WARNING: Preface Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
This page intentionally left blank.
IMB-M40H Table of Contents Revision History...................................................................... ii Preface .................................................................................... iii List of Figures ........................................................................ ix List of Tables.......................................................................... xi 1 Introduction ........................................................................ 1 1.1 Overview..........
Important Safety Instructions............................................... 37 Getting Service ......................................................................
IMB-M40H List of Figures Figure 1-1: Figure 1-2: Figure 2-1: Figure 2-2: IMB-M40H Block Diagram ............................................... 5 IMB-M40H Board Dimensions ....................................... 11 IMB-M40H Rear I/O Layout ........................................... 13 IMB-M40H Board Layout ...............................................
This page intentionally left blank.
IMB-M40H List of Tables Table Table Table Table Table 1-1: 1-2: 1-3: 1-4: 2-1: List of Tables IMB-M40H General Specifications................................... 3 Core™ i7-3770 Power Consumption ............................... 8 Core™ i3-3220 Power Consumption ............................... 9 Pentium® G2120 Power Consumption.......................... 10 IMB-M40H Board Layout Legend ..................................
This page intentionally left blank.
IMB-M40H 1 Introduction 1.1 Overview The ADLINK IMB-M40H is an ATX industrial motherboard supporting the 3rd Generation Intel® Core™ i7/i5/i3 and Pentium® processors in LGA1155 package to deliver a scalable high performance platform for a wide array of industrial applications. The IMB-M40H supports 22nm process CPUs at up to 3.4 GHz with integrated graphics and memory controllers, Direct Media Interface (DMI) and Flexible Display Interface (FDI) connectivity to the Intel® H61 Express Chipset.
1.2 Features 2 X ATX form factor (305 mm x 218 mm) X Supports 3rd Generation Intel® Core™ i7/i5/i3 and Pentium® processors in LGA1155 package X Integrated Intel® HD Graphics X One PCIe x16 slot, two PCIe x4 slots (with PCIe x1 signals), four PCI slots X Dual Gigabit Ethernet X 10x USB 2.
IMB-M40H 1.3 Specifications System ® CPU Intel Core™ (LGA115) • Intel® Core™ i7-3770, 3.40 GHz, 8M Cache, 22nm, 77W TDP (4C) • Intel® Core™ i5-3550S, 3.0 GHz, 6M Cache, 22nm, 65W TDP (4C) • Intel® Core™ i3-3220, 3.30 GHz, 3M Cache, 22nm, 55W TDP (2C) • Intel® Pentium® G2120, 3.10 GHz, 3M Cache, 22nm, 55W TDP (2C) • Intel® Celeron® G1620, 2.7 GHz, 2M Cache, 22nm, 55W TDP (2C) • Intel® Celeron® G540, 2.5 GHz, 2M Cache, 32nm, 65W TDP (2C) • Intel® Pentium® Dual Core G850, 2.
Expansion Slots • 1x PCIe-x16 Gen 2 • 2x PCIe x4 slot (with PCIe x1 signal) • 4x PCI slots Graphics Display Integrated Intel® HD Graphics VGA Dsub-15 connector, up to 2048x1536 @ 75 Hz DVI-D DVI-D connector, up to 1920x 1200 @ 60 Hz Controller Ethernet • Dual Gigabit Ethernet (Realtek® 8111E Gigabit Ethernet Controller) • Supports Preboot Execution Environment (PXE), Wake-On-LAN Ports Two RJ-45 Ethernet ports Form Factor Mechanical and Environment ATX Industrial Motherboard Dimensions 305 mm x
IMB-M40H 1.4 Block Diagram Dual Channel DDR3 1333/1600 Max. 16GB PCIe x16 Gen 2.0 for Discrete Graphic 3rd Gen Intel Core i7/i5/i3 dual/quad core 32/22nm VGA x2 Display Link x4 DMI PCIe to PCI Bridge DVI-D Realtek 8111E Realtek 8111E 4 SATA Ports at 3.0Gb/s HD Audio 2 PCIe x4 slots w/ PCIe x1 signal Intel H61 PCH 10 USB 2.
1.5 Functional Description Processor Support The IMB-M40H is an industrial motherboard supporting the 3rd generation Intel® Core™ processor family (Intel® Core™ i7/i5/i3) in LGA1155 socket. An integrated memory controller supports dual channel DDR3 1333/1600 MHz and Intel® HD Graphics is integrated onboard the CPU. The CPU provides a PCI Express x16 for external graphics or expansion. Direct Media Interface (DMI) and Flexible Display Interface (FDI) provide connectivity to the Intel® H61 Express Chipset.
IMB-M40H Serial ATA The IMB-M40H provides four SATA 3 GB/s ports. Hardware monitoring A built-in, proactive hardware monitoring system in the Super I/O monitors the CPU temperature, CPU fan speed, and voltage levels to prevent overheating and/or component damage, effect timely failure detection, and ensure stable supply of current for critical components. Watchdog Timer The watchdog timer (WDT) monitors system operations based on user-defined configurations.
1.6 Power Consumption Test Configuration Memory 2x Transcend 8GB DDR3 1600 DIMM (CL11 SEC K4B4G0846B-HYK0 8GB) Graphics Intel® Graphics Media Accelerator HD (integrated) Storage Seagate ST9160412AS Momentus 7200.4 160GB Power Supply Sunpower SPX-6500P1 500W Intel® Core™ i7-3770 Processor (8M Cache, 3.40 GHz) S1 Power Req. +5V +12V +3.3V Total Current (A) 0.64 1.04 0.46 — Power (W) 3.2 12.48 1.52 17.20 +3.3V Total Idle Load Power Req. +5V +12V Current (A) 1.32 0.59 0.
IMB-M40H Intel® Core™ i3-3220 Processor (3M Cache, 3.30 GHz) S1 Power Req. +5V +12V +3.3V Total Current (A) 0.64 0.92 0.38 — Power (W) 3.2 11.04 1.25 15.49 Power Req. +5V +3.3V Total Idle Load +12V Current (A) 1.15 0.56 0.50 — Power (W) 5.75 6.72 1.65 14.12 CPU Max Power Req. +5V +12V +3.3V Total Current (A) 1.20 3.24 0.73 — Power (W) 6.0 38.88 2.41 47.29 Power Req. +5V +3.3V Total Max. Load +12V Current (A) 2.13 2.74 0.72 — Power (W) 10.65 32.88 2.
Intel® Pentium® Processor G2120 (3M Cache, 3.10 GHz) S1 Power Req. +5V +12V +3.3V Total Current (A) 0.64 0.72 0.38 — Power (W) 3.2 8.64 1.25 13.09 Power Req. +5V +12V +3.3V Total Current (A) 1.21 0.57 0.48 — Power (W) 6.05 6.84 1.58 14.47 Idle Load CPU Max Power Req. +5V +12V +3.3V Total Current (A) 1.23 2.72 0.55 — Power (W) 6.15 32.64 1.81 40.60 Power Req. +5V +12V +3.3V Total Max. Load Current (A) 1.85 2.30 0.73 — Power (W) 9.25 27.6 2.41 39.
IMB-M40H 1.
1.8 Package Contents Before unpacking, check the shipping carton for any damage. If the shipping carton and/or contents are damaged, inform your dealer immediately. Retain the shipping carton and packing materials for inspection. Obtain authorization from the dealer before returning any product to ADLINK. X IMB-M40H ATX Industrial Motherboard X I/O shield X SATA cable x2 X Driver DVD X Quick Reference Guide WARNING: 12 The IMB-M40H must be protected from static discharge and physical shock.
IMB-M40H 2 Hardware Information 2.
Serial Port Connector (COM1) Pin # RS-232 1 DCD, Data Carrier Detect 2 RXD, Receive Data 3 TXD, Transmit Data 4 DTR, Data Terminal Ready 5 GND, ground 6 DSR, Data Set Ready 7 RTS, Request to Send 8 CTS, Clear to Send 9 RI, Ring Indicator DVI-D Connector 14 Pin # Signal Pin # Signal 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 TMDS Data2TMDS Data2+ TMDS Data2 Shield NC NC DDC Clock DDC Data NC TMDS Data1TMDS Data1+ TMDS Data1 Shield NC NC P5V GND 16 17 18 19 20 21 22 23 24 C1 C2 C3 C4 C5
IMB-M40H VGA Connector. Signal Name Pin # Pin # Signal Name Red 1 2 Green Blue 3 4 VCC pull-up GND 5 6 GND GND 7 8 GND VCC 9 10 GND VCC pull-up 11 12 DDC2B DATA HSYNC 13 14 VSYNC DDC2B CLK 15 LAN Port (RJ-45) Refer to the tables below for the LAN port pin and LED definitions.
USB Connectors Pin # Signal Name 1 Vcc 2 USB- 3 USB+ 4 GND Audio I/O port The three-jack audio I/O supports Line-In, Line-Out, and Mic-In functions. The blue Line-In jack connects to an audio source such as a CD player. The green Line-Out port connects to a speaker or headphone, while the pink Mic-In jack connects to a microphone.
IMB-M40H JDIO1 DIMM_A1 DIMM_B1 2.
AAFP1 Front Panel Audio Header ATX12V1 ATX 12V Power Connector DIMM_A1/B1 240-pin DIMM slots EATXPWR1 ATX Power Connector CLRTC1 Clear CMOS Jumper COM2~6 Serial Port Connectors 2~6 CPU_FAN CPU Fan Connector F_PANEL System Panel Pin Header JDIO1 Digital IO Connector JLPC LPC Pin Header JSETCOM6 COM6 Mode Jumpers PCIEX1_1/2 PCI Express x1 slots PCIEX16_1 PCI Express x16 slot PCI1~4 PCI slots PSON1 AT/ATX Mode Jumper SATA1~4 SATA 3 Gb/s Connector SPI_CN1 SPI Pin Header SYS _FA
IMB-M40H 2.3 Onboard Connectors & Jumpers Front Panel Audio Pin Header (AAFP1) Pin # Signal Pin # Signal 1 MIC2_L 2 AGND 3 MIC2_R 4 FP_PRES# 5 LIN2_R 6 SRTN1 7 SENSE A 8 NC 9 LIN2_L 10 SRTN2 1 2 ATX 12V Power Connector (ATX12V1) Pin # Signal 1 GND 2 GND 3 +12V DC 4 +12V DC 2 1 4 3 ATX Power Connector (EATXPWR1) Pin # Signal Pin # Signal 1 +3.3V 13 +3.3V 2 +3.
Serial Port Connectors - RS-232 (COM2~6) Pin # Signal 1 DCD Data Carrier Detect 2 DSR Data Set Ready 3 RXD Receive Data 4 RTS Request to Send 5 TXD Transmit Data 6 CTS Clear to Send 7 DTR Data Terminal Ready 8 RI 9 GND 10 NC Function 1 2 9 10 Ring Indicate Ground Key Serial Port Connector - RS-422/485 (COM6) Pin # RS-422 RS-485 1 TX- DATA- 2 N/A N/A 3 TX+ DATA+ 4 N/A N/A 5 RX+ N/A 6 N/A N/A 7 RX- N/A 8 N/A N/A 9 GND GND 10 Key Key 1 2 9
IMB-M40H CPU Fan Connector (CPU__FAN) Pin # Signal 1 GND 2 Fan power (+12V) 3 Fan Tachometer 4 Fan Speed Control 4 1 System Panel Pin Header (F_PANEL) Pin # 1 3 5 7 9 11 13 15 17 19 2 4 6 8 10 12 14 16 18 20 Signal Function Pin Group WDSPK Speaker signal NC Chassis Speaker NC P5V Power NC GND Ground Key Lock KEYLOCK Keyboard lock PLED Power LED signal Power LED NC P5V Power LED pull-up GND Ground RESET Button RESETBT RESET signal NC GND Ground Power On Button POWERBT Power-on signal NC NC H
Digital IO Connector (JDIO1) Pin # Signal Pin # Signal 1 SIO_GPIO0 2 DIO_GPIO0 3 SIO_GPIO1 4 DIO_GPIO1 5 SIO_GPIO2 6 DIO_GPIO2 7 SIO_GPIO3 8 DIO_GPIO3 9 SIO_GPIO4 10 DIO_GPIO4 11 SIO_GPIO5 12 DIO_GPIO5 13 SIO_GPIO6 14 DIO_GPIO6 15 SIO_GPIO7 16 DIO_GPIO7 17 SIO_GPIO8 18 DIO_GPIO8 19 SIO_GPIO9 20 DIO_GPIO9 21 SIO_GPIO10 22 DIO_GPIO10 23 SIO_GPIO11 24 DIO_GPIO11 25 SIO_GPIO12 26 DIO_GPIO12 27 SIO_GPIO13 28 DIO_GPIO13 29 SIO_GPIO14 30 DIO_GPIO14 31
IMB-M40H SATA Connectors (SATA1~4) Pin # Signal 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND 1 7 SPI Pin Header (SPI_CN1) Pin # Signal Pin # Signal 1 +3V ROM 2 GND 3 F_SPI_CS# 4 F_SPI_CLK 5 F_SPI_MISO 6 F_SPI_MOSI 7 SPI_HOLD# 8 NC 1 System Fan Connector (SYS_FAN) Pin # Signal 1 GND 2 Fan Power (+12V) 3 Fan Tachometer 3 1 USB 2.
2.4 Jumpers Clear CMOS (CLRTC1) The CMOS RAM data contains the date / time and BIOS setting information. CMOS is powered by the onboard button cell battery. To erase the CMOS RAM data: 1. Power down and disconnect power from the system. 2. Short pins 2-3 on JP1. 3. Reconnect power and power up the system. 4. After power up, remove the jumper cap from pins 2-3 and reinstall it to pins 1-2.
IMB-M40H AT/ATX Mode Jumper (PSON1) Pin # Signal 1 PSON_AT 2 FRP_PANSWUN 3 NC Status Connection AT Mode 1–2 ATX Mode 2 – 3 (default) Hardware Information JCLRT_C2 25
This page intentionally left blank.
IMB-M40H 3 Getting Started This chapter provides information on how to install components on the IMB-M40H motherboard. 3.1 Installing the CPU The IMB-M40H supports an Intel® Core™ i7/i5/i3 or Pentium® processor in an LGA1155 socket. WARNING: Disconnect all power to the board before installing a CPU to prevent damaging the board and CPU. Do not touch socket contacts. Damaging the contacts voids the product warranty. Follow the installation instructions carefully to avoid damaging the board components.
2. Raise the locking arm to unlock the load plate. 3. Lift the load plate to uncover the socket. 4. Remove the plastic protective cover from the socket. Note the locations of the alignment keys (A) and Pin 1 indicator (B). B A Do NOT touch socket contacts.
IMB-M40H 5. Hold the CPU using thumb and forefinger as shown. Position the CPU over the socket, matching the notches on the sides of the CPU with the alignment keys on the socket (A). The golden triangle on the CPU must be positioned at the corner of the socket with the Pin 1 indicator as shown (B). B A The CPU fits into the socket in only one orientation. DO NOT force it into the socket to avoid causing damage. WARNING: 6. Carefully place the CPU into the socket vertically.
7. Gently lower the load plate. Make sure the front edge of the plate is under the screw as indicated. 8. Lower the locking arm and fasten it to the retention tab (A). The load plate should be locked underneath the screw as shown (B).
IMB-M40H 3.2 Installing the CPU Fan and Heatsink CAUTION: The CPU requires a chassis with an airflow inlet and maximum internal ambient temperature of 60° C. A specially-designed CPU fan and heatsink must be installed before using the motherboard. Failure to install a CPU fan and heatsink may damage the system host board and/or the CPU.
3.3 Installing Memory Modules The IMB-M40H supports up to 16 GB of DDR3 1066/1333 MHz (2nd Gen Intel® Core™) or 1333/1600 MHz (3rd Gen Intel® Core™) memory modules in two DIMM sockets. A DDR3 module has a 240-pin footprint compared to the legacy 184-pin DDR DIMM. DDR3 modules are notched to facilitate correct installation in the DIMM sockets and prevent installation of DDR2 or DDR modules. Disconnect all power to the board before installing a memory module to prevent damaging the board and memory module.
IMB-M40H To install a memory module: 1. Locate the DIMM sockets on the motherboard. 2. Press the socket’s retaining clips outward to unlock. 3. Align the memory module on the socket making sure that the notch matches the break on the socket.
4. Insert the module firmly into the slot until the retaining clips snap back inwards and the module is securely seated.
IMB-M40H 4 Driver Installation This chapter provides information on how to install the IMB-M40H device drivers under Windows XP. The device drivers are located in the following ADLINK All-in-One CD directories: Chipset X:\CHIP Display X:\VGA Ethernet X:\LAN Audio X:\AUDIO .NET X:\OTHERS Follow the instructions below to install the required IMB-M40H drivers: 1. Install the Windows operating system before installing any driver.
This page intentionally left blank.
IMB-M40H Important Safety Instructions For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment. X Read these safety instructions carefully. X Keep this user’s manual for future reference. X Read the specifications section of this manual for detailed information on the operating environment of this equipment.
X Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel. A Lithium-type battery may be provided for uninterrupted, backup or emergency power. WARNING: X 38 Risk of explosion if battery is replaced with one of an incorrect type. Dispose of used batteries appropriately.
IMB-M40H Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan ᄅؑקխࡉ৬ԫሁ 166 ᇆ 9 ᑔ Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: service@adlinktech.com Ampro ADLINK Technology, Inc. Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.com ADLINK Technology (China) Co.
ADLINK Technology, Inc. (French Liaison Office) Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: france@adlinktech.com ADLINK Technology Japan Corporation Address: ͱ101-0045 ᵅҀ䛑गҷ⬄ऎ⼲⬄䤯 ⬎ފ3-7-4 ⼲⬄ 374 ɛɳ 4F KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho, Chiyoda-ku, Tokyo 101-0045, Japan Tel: +81-3-4455-3722 Fax: +81-3-5209-6013 Email: japan@adlinktech.com ADLINK Technology, Inc.
