IMB-M42H ATX Intel® Core™ i7/i5/i3 Industrial Motherboard User’s Manual Manual Rev.: 2.00 Revision Date: Sept. 30, 2014 Part No: 50-1X010-1000 Advance Technologies; Automate the World.
Revision History ii Revision Release Date Description of Change(s) 2.00 Sept.
IMB-M42H Preface Copyright 2014 ADLINK Technology, Inc. This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer.
Conventions Take note of the following conventions used throughout this manual to make sure that users perform certain tasks and instructions properly. Additional information, aids, and tips that help users perform tasks. NOTE: CAUTION: WARNING: iv Information to prevent minor physical injury, component damage, data loss, and/or program corruption when trying to complete a task.
IMB-M42H Table of Contents Revision History...................................................................... ii Preface .................................................................................... iii List of Figures ....................................................................... vii List of Tables.......................................................................... ix 1 Introduction ........................................................................ 1 1.1 Features..........
A.8 Storage Configuration ........................................................ 30 A.9 Intel® Smart Connect Technology ..................................... 31 A.10 Super IO Configuration ...................................................... 32 A.11 ACPI Configuration ............................................................ 33 A.12 USB Configuration ............................................................. 35 A.13 Voltage Configuration ........................................................
IMB-M42H List of Figures Figure 1-1: IMB-M42H Motherboard .................................................. 4 Figure 1-2: IMB-M42H I/O Panel........................................................ 5 Figure 1-3: LAN Port LED Indicators..................................................
This page intentionally left blank.
IMB-M42H List of Tables Table Table Table Table Table Table Table Table 1-1: 1-2: 1-3: 1-4: 2-1: 2-2: 2-3: A-1: List of Tables IMB-M42H Motherboard Legend ..................................... 5 IMB-M42H I/O Legend..................................................... 6 COM Port Pin Definitions................................................. 6 LAN Port LED Legend ..................................................... 7 CPU Fan Connection Options .......................................
This page intentionally left blank.
IMB-M42H 1 Introduction With specification and BIOS updates, the content of this manual is subject to change without notice. Updated versions, as well as the latest CPU support lists are available at http://www.adlinktech.com For technical support, please visit http://askanexpert.adlinktech.com/AAE/Answers.aspx for model-specific information. NOTE: 1.
1.2 Specifications System • • • • CPUs • • • • Intel® Core™ i7-4790S, 3.2GHz, 8MB Cache, 22nm, 65W TDP, LGA1150(4C/8T) Intel® Core™ i7-4770S, 3.1GHz, 8MB Cache, 22nm, 65W TDP, LGA1150(4C/8T) Intel® Core™ i5-4590S, 3.0GHz, 6MB Cache, 22nm, 65W TDP, LGA1150(4C/4T) Intel® Core™ i5-4570S, 2.9GHz, 6MB Cache, 22nm, 65W TDP, LGA1150(4C/4T) Intel® Core™ i3-4360, 3.7GHz, 4MB Cache, 22nm, 54W TDP, LGA1150(2C/4T) Intel® Core™ i3-4330, 3.5GHz, 4MB Cache, 22nm, 54W TDP, LGA1150(2C/4T) Intel® Core™ G3420, 3.
IMB-M42H Internal I/O Rear I/O • • • • • • 2x USB 2.0 pin headers (4 ports) 4x RS-232 pin headers 1x parallel port 1x HD Audio pin header 1x TPM pin header 1x 10-pin/2.54mm GPIO pin header: 4 in and 4 out, one ground pin and one power pin (5V/12V, jumper selected), API sample code ready • • • • • • • • • • • VGA HDMI DisplayPort Ethernet 2 x USB 3.0, 4 x USB 2.
1.3 Motherboard Topography 3 2 3 2 11 PS2 K ey boa rd /M o u s e COM1 DISPL AY 1 CPU_F AN2 CPU_F AN1 Top: LA N CHA_F AN1 CMOS Battery AT X P W R 1 CHA_F AN2 4 4 S ATA _0 S ATA _4 S ATA _5 H D MI US B 2 .0 T: USB 2 B: USB 3 S ATA _1 D D R 3 _ A 1 ( 6 4 b i t, 2 4 0 - p i n m o d u l e ) COM2 VGA1 US B 3 .0 T: USB0 B: USB 1 US B 2 .
IMB-M42H 1 ATX 12V Power Connector 2 3-Pin CPU FAN Connector 3 4-Pin CPU FAN Connector 4 24-pin ATX Power Input Connector 5 SATA3 Connectors (SATA_0, SATA_1) SATA2 Connectors (SATA_4, SATA_5) 6 3-Pin Chassis FAN Connector 7 4-Pin Chassis FAN Connector 8 System Panel Header 9 COM3, 4, 5, 6 Headers (RS232) 10 ATX/AT mode Selection 11 Clear CMOS Header 12 Printer Port Header 13 USB2.
1 COM Port (COM1) 2 COM Port (COM2) 3 USB 2.0 Ports (USB2_3) 4 LAN RJ-45 Port 5 Line In 6 Line Out 7 Mic In 8 USB 2.0 Ports (USB4_5) 9 HDMI Port (HDMI1) 10 USB 3.0 Ports (USB0_1) 11 D-Sub Port (VGA1) 12 PS/2 Mouse/Keyboard Port 13 DisplayPort (DP1) Table 1-2: IMB-M42H I/O Legend The IMB-M42H supports RS232/422/485 on COM ports 1 and 2, with pin definitions as follows, with both COM ports configurable in BIOS setup. See Appendix A, Super IO Configuration for details.
IMB-M42H ACT/LINK SPEED Figure 1-3: LAN Port LED Indicators ACT/LINK Off No Link Blinking Transmission Underway Lit Link SPEED Off 10 Mb/s Orange 100 Mb/s Green 1 Gb/s Table 1-4: LAN Port LED Legend Introduction 7
This page intentionally left blank.
IMB-M42H 2 Getting Started 2.1 Package Contents Before unpacking, check the shipping carton for any damage. If the shipping carton and/or contents are damaged, inform your dealer immediately. Retain the shipping carton and packing materials for inspection. Obtain authorization from the dealer before returning any product to ADLINK. X IMB-M42H ATX industrial motherboard X I/O shield X The IMB-M42H must be protected from static WARNING: Getting Started discharge and physical shock.
2.2 Mounting the motherboard Mount the motherboard to the chassis with screws through the provided screw holes. Avoid over-tightening screws to prevent PCB damage. CAUTION: 2.3 Installing Memory Modules (DIMM) The IMB-M42H provides two 240-pin DDR3 DIMM slots supporting Dual Channel Memory technology. X Dual channel configuration requires installation NOTE: of DDR3 DIMM pairs of identical brand, speed, size, and chip type.
IMB-M42H 3. Align the memory module on the socket, making sure that the module notch matches the slot rail. 4. Insert the module firmly into the slot until the retaining clips snap back inwards and the module is securely seated.
2.4 Installing Expansion Cards (PCI and PCI Express) The IMB-M42H provides: X 4x PCI slots receiving expansion cards with 32-bit PCI interface X 2x PCIE (PCI Express) slots, PCIE1 (PCIE x16 slot; blue) for PCI Express x16 lane width graphics cards, and PCIE3 (PCIE x4 slot; white) for PCI Express x4 lane width I/O cards Before installing expansion cards, ensure the power supply is switched off or disconnected. Check the card's documentation and perform requisite system configurations before installation.
IMB-M42H 2.5 Jumpers Clear CMOS (CLCMOS) The CMOS RAM data contains the Date/Time and BIOS setting information. CMOS is powered by an onboard button cell battery. To erase the CMOS RAM data: 1. Power down and disconnect power from the system. 2. Short pins 2-3 on JP1. 3. Reconnect power and power up the system. 4. After power up, remove the jumper cap from pins 2-3 and reinstall it to pins 1-2.
When setting "Resume from AC power lost " to "on" in BIOS, or setting jumper to "AT mode", short PWR_LOSS1 pin next to the PWR_JP1 if the power supply unit has slow electrical discharge. NOTE: Digital I/O Power Select (3-pin JGPIO_PWR1) Status Connection JCLRT_C2 +12V 1–2 +5V 2 – 3 (default) 2.6 Onboard Headers and Connectors Do not place jumper covers over headers and connectors to avoid permanent damage. CAUTION: For location on board, see Section 1.
IMB-M42H CPU Fan Connectors (4-pin CPU_FAN1) Connect the CPU fan cable to the connector and match the black wire to the ground pin. 4 1 Both 4-Pin (Quiet Fan) and 3-Pin CPU fan support are available, with or without fan speed control function. For 3-Pin CPU fan connection, use Pins 1-3, as shown.
Connect the fan cable to the fan connector and match the black wire to the ground pin. 4-Pin Connection (CHA_FAN1) 3-Pin Connection (CHA_FAN2) FAN_SPEED_CONTROL CPU_FAN_SPEED +12V GND CPU_FAN_SPEED +12V GND X Table 2-2: System Fan Connection Options ATX Power Input Connector (24-pin ATXPWR1) 12 24 1 13 Please connect an ATX power supply to this connector. While a 24-pin ATX power connector is provided, conventional 20-pin ATX power supply is also supported.
IMB-M42H ATX 12V Power Input Connector (8-pin ATX12V1) Please connect an ATX power supply to this connector. 5 8 4 1 While an 8-pin ATX 12V power connector is provided, conventional 4-pin ATX power supply is also supported.
COM3, 4, 5, 6 Headers (9-pin COM3/COM4/COM5/COM6) 2 1 System Panel Header (9-pin PANEL1) Accommodates multiple front panel system functions.
IMB-M42H Connect the power switch, reset switch and system status indicator on the chassis to the header as follows. Note positive and negative pins positions before connecting the cables. Connect to the power switch on the chassis front panel and configure as desired. Connect to the reset switch on RESET (Reset Switch) the chassis front panel. Connect to the power status indicator on the chassis front panel.
SATA2 Connectors (SATA_4/SATA_5) Enable Serial ATA2 data input at up to 3.0 Gb/s. SATA_4 SATA_5 SATA3 Connectors (SATA_0/SATA_1) Enable Serial ATA3 data input at up to 6.0 Gb/s. SATA_0 SATA_1 USB 2.0 Headers (9-pin USB6_7/USB8_9)) PWR + GNDNC In addition to the four on the I/O panel, two USB 2.0 headers on the board each support two USB 2.0 ports.
IMB-M42H Chassis Intrusion Headers (2-pin CI1/CI2) The motherboard supports CASE OPEN notification if the chassis is equipped with intrusion detection capability. 1 GND Signal Front Panel Audio Header (9-pin HD_AUDIO1) Provides front audio cable connection.
Print Port Header (25-pin LPT1) +5V 48MHz GND GND SERIRQ# Enables convenient front panel connection of printer devices. +3VSB S_PWRDWN# LAD0 GND LAD1 +3V LAD2 LAD3 PCIRST# SMB_DATA_MAIN SMB_CLK_MAIN FRAME PCICLK GND 2 1 1 2.7 Driver Installation Download the requisite drivers for http://www.adlinktech.com and install.
IMB-M42H Appendix A - UEFI Setup Utility A.1 Introduction This section explains how to use the UEFI Setup Utility to configure your system. The UEFI chip on the motherboard stores the UEFI Setup Utility. You may run the UEFI Setup Utility when you start up the computer. Select or during the Power-On-Self-Test (POST) to enter the UEFI Setup Utility, otherwise, POST will continue with its test routines.
A.3 Navigation Keys Key(s) Function R/L Arrow Moves cursor left or right to select Menus U/D Arrow Moves cursor up or down to select items +/- Changes option for the selected item Enter Opens the selected Menu F1 Displays General Help F7 Discards changes F9 Loads default values for all settings F10 Saves changes and exits Setup F12 Prints screen ESC Opens the Exit Menu or exits the current screen Table A-1: Navigation Key Functions A.
IMB-M42H A.5 Advanced Menu Accesses CPU Configuration, Chipset Configuration, Storage Configuration, Intel® Smart Connect Technology, Super IO Configuration, ACPI Configuration, USB Configuration, Voltage Configuration and Instant Flash settings. Incorrect settings in this menu can cause serious malfunction CAUTION: Instant Flash Instant Flash is a UEFI flash utility embedded in Flash ROM.
that the USB flash drive or hard drive must use FAT32/16/12 file system. If you execute Instant Flash utility, the utility will show the UEFI files and their respective information. Select the proper UEFI file to update your UEFI, and reboot your system after UEFI update process completes. A.6 CPU Configuration Active Processor Cores Selects the number of cores enabled in each processor package.
IMB-M42H CPU C3 State Support Enables C3 sleep state for lower power consumption. CPU C6 State Support Enables C6 deep sleep state for lower power consumption. CPU C7 State Support Enables C7 deep sleep state for lower power consumption. Package C State Support Enables CPU, PCIe, memory, graphics C State Support for power conservation.
Intel Virtualization Technology When enabled, VMM (Virtual Machine Architecture) utilizes additional hardware capabilities provided by Vanderpool Technology, hidden if the installed CPU does not support Intel Virtualization Technology. Hardware Prefetcher Turns MLC streamer prefetcher on and off. Adjacent Cache Line Prefetch Turns prefetching of adjacent cache lines on and off. A.
IMB-M42H Primary Graphics Adapter Onboard, PCI, or PCI Express can be selected as boot graphic adapter priority, with default PCI Express. VT-d Enables/disables Intel® VT-d technology (Intel® Virtualization Technology for Directed I/O), with default Disabled. PCIE1 Link Speed Selects link speed for PCIE1. PCIE3 Link Speed Selects link speed for PCIE3. Share Memory Configure the size of memory allocated to the integrated graphics processor when the system boots.
Onboard HDMI HD Audio Enables/disables onboard HDMI HD Audio. Onboard LAN Enables/disables onboard LAN feature. Restore on AC/Power Loss Sets power resume state after AC power loss, with Power Off maintaining power off on resume, Power On booting the system upon resume. A.8 Storage Configuration SATA Controller(s) Enables/disables SATA Controller.
IMB-M42H SATA Mode Selection Selects SATA mode, from IDE, AHCI (default), and Disabled. AHCI (Advanced Host Controller Interface) supports NCQ and other features to improve SATA disk performance, IDE mode does not. SATA Aggressive Link Power Mgmt Configures SATA Aggressive Link Power Management. Hard Disk S.M.A.R.T. Enables/disables S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) feature. A.
A.10 Super IO Configuration COM1 Configuration Sets parameters for COM1, from port type [RS232], [RS422] or [RS485]. COM2 Configuration Sets parameters for COM2, from port type [RS232], [RS422] or [RS485]. COM3 Configuration Sets parameters for COM3. COM4 Configuration Sets parameters for COM4.
IMB-M42H COM5 Configuration Sets parameters for COM5. COM6 Configuration Sets parameters for COM6. LPT1 Port Configuration Sets parameters for the onboard parallel port. WDT Timeout Reset Enables/disables Watch Dog Timer timeout to reset system, with default Disabled. A.
Suspend to RAM Selects auto-detect or disable for Suspend-to-RAM, with default of Auto, if OS supports. Check Ready Bit Enables/disables Check Ready Bit. ACPI HPET Table Enables/disables ACPI HPET Table, with default Enabled, to be set when Windows® certification is to be submitted. PS/2 Keyboard Power On Enables/disables PS/2 keyboard power on when in power-soft-off mode. PCI Devices Power On Enables/disables PCI device power on from power-soft-off mode.
IMB-M42H A.12 USB Configuration USB Controller Enables/disables the USB controller. Intel USB 3.0 Mode Enables/disables Intel USB 3.0 mode. Legacy USB Support Selects legacy support for USB devices, from default Enabled, supporting legacy USB, Auto, supporting legacy USB when devices are connected, and Disabled (if USB compatibility issues occur, it is recommended to select Disabled to enter OS), and UEFI Setup Only, in which USB devices are allowed only under UEFI setup and Windows/Linux OS.
Legacy USB 3.0 Support Enables/disables legacy support for USB 3.0 devices, with default Enabled. A.13 Voltage Configuration Selects DRAM Voltage, with default 1.50V.
IMB-M42H A.14 Hardware Health Event Monitoring In addition to monitoring current CPU, fan(s), and voltage status, the following settings can be configured. CPU_FAN1 & 2 Setting Sets speed for CPU fans 1 & 2, from Full On (default) and Automatic. CHA_FAN1 & 2 Setting Sets speed for chassis fans 1 & 2, from Full On (default) and Automatic. Over Temperature Protection Enables/disables Over Temperature Protection, with default Enabled.
Case Open Feature Enables/disables case open detection with default Disabled. Clear Status Appears only when a case opening has been detected. Clears the record of previous chassis intrusion notifications. A.15 Boot Boot From Onboard LAN Enables/disables Boot From Onboard LAN. Setup Prompt Timeout Displays the number of seconds to wait for setup activation key, with 65535(0XFFFF) indicating indefinite wait.
IMB-M42H Bootup Num-Lock When set to [On], automatically activates Num Lock keypad following boot. Boot Beep Enables/disables Boot Beep, available only when a chassis buzzer is installed. Full Screen Logo Enables/disables OEM Logo, with default Enabled. CSM Must be disabled when Fast Boot is enabled, with default Enabled. When Enabled, opens CSM submenu.
Enable to launch the Compatibility Support Module. Only disable when running a WHCK test. If OS is Windows® 8 64-bit and all devices support UEFI, CSM can be disabled for faster boot. Launch PXE OpROM Policy Enables UEFI to run those devices that support UEFI option ROM only. Selecting Legacy enables only devices that support legacy option ROM only. Launch Storage OpROM Policy Enables UEFI to run those devices that support UEFI option ROM only.
IMB-M42H A.16 Security In addition to setting, changing, or clearing supervisor/user password for the system, this menu provides the following settings. Secure Boot Enables/Disables Secure Boot, with default Disabled.
A.17 Exit Save Changes and Exit Generates confirmation prompt. Selecting OK saves changes and exits. Discard Changes and Exit Generates confirmation prompt. Selecting OK exits without saving any changes. Discard Changes Generates confirmation prompt. Selecting OK discards all changes.
IMB-M42H Important Safety Instructions For user safety, please read and follow all instructions, WARNINGS, CAUTIONS, and NOTES marked in this manual and on the associated equipment before handling/operating the equipment. X Read these safety instructions carefully. X Keep this user’s manual for future reference. X Read the specifications section of this manual for detailed information on the operating environment of this equipment.
X Never attempt to fix the equipment. Equipment should only be serviced by qualified personnel. A Lithium-type battery may be provided for uninterrupted, backup or emergency power. WARNING: X 44 Risk of explosion if battery is replaced with one of an incorrect type. Dispose of used batteries appropriately.
IMB-M42H Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan ᄅؑקխࡉ৬ԫሁ 166 ᇆ 9 ᑔ Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: service@adlinktech.com Ampro ADLINK Technology, Inc. Address: 5215 Hellyer Avenue, #110 San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.com ADLINK Technology (China) Co.
ADLINK Technology, Inc. (French Liaison Office) Address: 6 allée de Londres, Immeuble Ceylan 91940 Les Ulis, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: france@adlinktech.com ADLINK Technology Japan Corporation Address: ͱ101-0045 ᵅҀ䛑गҷ⬄ऎ⼲⬄䤯 ⬎ފ3-7-4 ⼲⬄ 374 ɛɳ 4F KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho, Chiyoda-ku, Tokyo 101-0045, Japan Tel: +81-3-4455-3722 Fax: +81-3-5209-6013 Email: japan@adlinktech.com ADLINK Technology, Inc.
