LEC‐3517 (Computer‐on‐Module) Technical Reference P/N 50‐1Z152‐1000 Advance Technologies. Automate the World.
Disclaimer Information in this document is provided in connection with ADLINK products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document.
LEC-3517 Table of Contents 1 Overview ........................................................................................................................... 1 1.1 Block Diagram........................................................................................................................ 1 1.2 Major Components (ICs)........................................................................................................ 2 1.3 Connectors.......................................................
iv
LEC-3517 1 Overview This initial manual version presents a general overview of the LEC-3517 Computer-On-Module (COM). The next version of this manual shall include more detailed information including user interface descriptions, boot setup access and menu settings, memory map, interrupt channel assignments, and I/O address map. After reviewing this document you should understand the following features of the LEC-3517.
1.2 Major Components (ICs) Table 1-1 lists the major integrated circuits on the LEC-3517, including a brief description of each IC. Figure 1-2 shows the locations of the major ICs. Table 1-1: Major Integrated Circuit Descriptions and Functions Chip Type Mfg.
LEC-3517 1.3 Connectors Table 1-2 describes the connectors shown in Figure 1-3. Table 1-2: Module Connector Description Board Access Connector# J1 – SMARC P-S Top/ Bottom Top Top JTAG1 LED1 Description 314-pin, MXM edge connector for Memory, Video, and I/O functions. 10-pin connector for debugging Green LED for Power On LEC_3517_Top_Conn_a Key: J1 - SMARC Connector J1 Figure 1-3: Connector Location (Top Side) 1.
Mechanical Specifications 1.97 (50.00mm) 1.81 (46.00mm) 1.44 (36.69mm) 0.78 (19.69mm) 0.47 (12.00mm) 0.30 (7.70mm) 0.24 (6.20mm) J1 0.00 3.23 (82.0mm) 3.16 (80.30mm) 3.07 (78.00mm) 2.14 (54.39mm) 1.54 (39.00mm) 1.08 (27.39mm) 0.16 (4.00mm) 0.00 LEC_3517_Top_Dmn_a Figure 1-4: Mechanical Dimensions (Top Side) All dimensions are given in inches and millimeters. Power Specifications Table 1-4 provides the power requirements for this module.
LEC-3517 Environmental Specifications Table 1-5 provides the most efficient operating and storage condition ranges required for this module.
Table 1-7: SMARC P-S Connector Signal Descriptions (Continued) P19 P20 P21 P22 P23 P24 P25 P26 P27 P28 P29 P30 P31 P32 P33 P34 P35 P36 P37 P38 P39 P40 P41 P42 P43 P44 P45 P46 P47 P48 P49 P50 P51 P52 P53 P54 P55 P56 P57 P58 P59 P60 P61 P62 P63 P64 P65 P66 P67 P68 6 Not connected Not connected GBE_LINK100# (Ethernet Speed LED) Not connected Not connected Not connected GBE_LINK_ACT# (LAN Link LED) GBE_MDI1GBE_MDI1+ GBE_CTREF GBE0_MDI0GBE0_MDI0+ SPI0_CS1# GND SDIO_WP SDIO_CMD SDIO_CD# SDIO_CK SDIO_PWR_EN GND S
LEC-3517 Table 1-7: SMARC P-S Connector Signal Descriptions (Continued) P69 P70 P71 P72 P73 P74 P75 P76 P77 P78 P79 P80 P81 P82 P83 P84 P85 P86 P87 P88 P89 P90 P91 P92 P93 P94 P95 P96 P97 P98 P99 P100 P101 P102 P103 P104 P105 P106 P107 P108 P109 P110 P111 P112 P113 P114 P115 P116 P117 P118 Overview Not connected Not connected USB2_EN_OC# Not connected Not connected Not connected Key Not connected Not connected Not connected Not connected GND Not connected Not connected GND Not connected Not connected GND
Table 1-7: SMARC P-S Connector Signal Descriptions (Continued) P119 P120 P121 P122 P123 P124 P125 P126 P127 P128 P129 P130 P131 P132 P133 P134 P135 P136 P137 P138 P139 P140 P141 P142 P143 P144 P145 P146 P147 P148 P149 P150 P151 P152 P153 P154 P155 P156 8 GPIO11 GND I2C_PM_CK I2C_PM_DAT BOOT_SEL0# BOOT_SEL1# BOOT_SEL2# RESET_OUT# RESET_IN# POWER_BTN# SER0_TX SER0_RX SER0_RTS# SER0_CTS# GND SER1_TX SER1_RX SER2_TX SER2_RX SER2_RTS# SER2_CTS# SER3_TX SER3_RX GND CAN0_TX CAN0_RX Not connected Not connected VD
LEC-3517 Debug (JTAG1) Table 1-8 lists the pin signals of the JTAG1 header, which provides 10-pins, 2 rows, odd/even pin sequence (1, 2) with 0.039" (1.00mm) pitch. Table 1-8: Camera 1 Pin Signals (CAM1) Pin # 1 2 3 4 5 6 7 8 9 10 Signal JTAG_PWR JTAG_nTRST JTAG_TMS JTAG_TDO JTAG_TDI JTAG_TCK JTAG_RTCK GND MFG_nMODEL GND NOTE: The shaded table cells denote ground.
10 Overview
LEC-3517 Appendix A Technical Support ADLINK Technology, Inc. provides a number of methods for contacting Technical Support listed in Table A-1 below. Requests for support through Ask an Expert are given the highest priorities, and usually will be addressed within one working day. ADLINK Ask an Expert – This is a comprehensive support center designed to meet all your technical needs. This service is free and available 24 hours a day through the ADLINK web site at http://www.adlinktech.com/AAE/.
Table A-1: Technical Support Contact Information (Continued) ADLINK Technology Beijing Address: ࣫ҀᏖ⍋⎔ऎϞഄϰ䏃 1 োⲜ߯ࡼॺ E ᑻ 801 ᅸ(100085) Rm. 801, Power Creative E, No. 1, Shang Di East Rd., Beijing, 100085 China Tel: +86-10-5885-8666 Fax: +86-10-5885-8626 Email: market@adlinktech.com ADLINK Technology Shenzhen Address: ⏅ഇᏖफቅऎ⾥ᡔುफऎ催ᮄफϗ䘧 ᭄ᄫᡔᴃು A1 ᷟ 2 ὐ C ऎ (518057) 2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7, High-Tech Industrial Park S.
LEC-3517 Table A-1: Technical Support Contact Information (Continued) ADLINK Technology, Inc. (Israeli Liaison Office) Address: 6 Hasadna St., Kfar Saba 44424, Israel Tel: +972-9-7446541 Fax: +972-9-7446542 Email: israel@adlinktech.
14
