MilSystemTM User’s Guide P/N 50-1Z028-1010
Notice Page DISCLAIMER ADLINK Technology, Incorporated makes no representations or warranties with respect to the contents of this manual or of the associated ADLINK products, and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. ADLINK shall under no circumstances be liable for incidental or consequential damages or related expenses resulting from the use of this product, even if it has been notified of the possibility of such damages.
Contents MilSystem Setup .................................................................................................................................1 About the MilSystem ........................................................................................................................1 Using this Guide .........................................................................................................................1 Requirements .............................................................
Contents iv User’s Guide MilSystem
MilSystem Setup About the MilSystem The MilSystem products are intended for users of turn-key embedded systems who require long life-cycle, configuration controlled computers with MIL-STD-D38999 connectors. MilSystem models each feature one of three Extreme Rugged™ computer boards: the LittleBoard 735 Single Board Computer (SBC), the LittleBoard 800 SBC, or the COM 840 (Computer On Module) with the EBX baseboard.
MilSystem Setup Device/Peripheral Connections • Ethernet (LAN) connection • USB device connections • Up to two PC/104 expansion modules (except MilSystem with COM 840 module) Power Specifications Tables 1 through 3 define the current draw values of the three MilSystem models, featuring either the LittleBoard 735, COM 840 with EBX Baseboard, or the LittleBoard 800. The tables capture In-Rush, Idle, and Burn-In-Test (BIT) currents at incremental input voltages from +14 to +32 VDC.
MilSystem Setup Table 2 lists the current draw values of the MilSystem with the COM 840 and the EBX Baseboard. Table 2. System Power Requirements (COM 840 with EBX Baseboard, 1.6 GHz CoreTM 2 Duo CPU) Input Type In-rush Current (@ 104.26W Power) Typical Idle Current (@ 37.96W Power) Typical BIT Current (@ 48.43W Power) +14VDC 7.45A 2.71A 3.46A +16VDC 6.52A 2.38A 3.03A +18VDC 5.79A 2.11A 2.69A +20VDC 5.21A 1.90A 2.42A +22VDC 4.74A 1.73A 2.20A +24VDC 4.34A 1.58A 2.02A +26VDC 4.
MilSystem Setup Table 3 lists the current draw values of the MilSystem with the LittleBoard 800. Table 3. System Power Requirements (LittleBoard 800, 1.4 GHz Pentium M CPU) Input Type In-rush Current (@ 170.88W Power) Typical Idle Current (@ 9.54W Power) Typical BIT Current (@ 13.18W Power) +14VDC 12.21A 0.68A 0.94A +16VDC 10.68A 0.60A 0.82A +18VDC 9.49A 0.53A 0.73A +20VDC 8.54A 0.48A 0.66A +22VDC 7.77A 0.43A 0.60A +24VDC 7.12A 0.40A 0.55A +26VDC 6.57A 0.37A 0.
MilSystem Setup What’s in the Box The Contents List identifies the items in the shipping box for the MilSystem Unit and the MilSystem Accessory Kit (sold separately.) See Figure 1.
MilSystem Setup Setup Steps Follow the setup steps in this section in the order listed. Skip any steps that do not apply to your application. References to other ADLINK manuals are provided in this section for more information about installation and use of this MilSystem. Table 5. Preparations 1) Open shipping box. 2) Verify contents. • Locate the MilSystem Contents List. • Unpack the contents of the shipping box.
MilSystem Setup Installing Mounting Hardware 6) Install mounting screws (1/4"-20 [6.35mm].) • CL Install mounting screws (not included) for surface or wall mounting to the four mounting flanges of the MilSystem. See Figure 2. 7,36" 187 mm 5.51" 140 mm CL CL 11.02" 280 mm 12.20" 310 mm 10.00" 254 mm CL 8.18" 208 mm Figure 2.
MilSystem Setup Connecting Peripherals • Refer to Figure 3 for locations and descriptions of the connectors before making connections or powering on the MilSystem. • Connect the USB or PS2 keyboard to the appropriate connector on the MC-1 connector. • Connect the USB mouse (PS2 not supported) to the appropriate connector on the MC-1 connector. • Connect the CRT or LCD monitor through its 15-pin cable to the VGA cable on the MC-1 connector.
MilSystem Setup Table 6. I/O Panel Connectors (Refer to Figure 3 for connector locations.) Control/Connector Description MC-1 This military connector provides signals for VGA, Ethernet, PS2 Keyboard, Stereo Audio Out, Stereo Line In, Mic In, ACPI Power In, Reset In, Power On LED, HDD Activity LED, SATA, USB 2.0. MC-2 This military connector provides signals for USB 2.0, Ethernet, and RS232/ 485/422 COM Ports. MC-3 This military connector provides signals for Parallel and LVDS.
MilSystem Setup Table 7.
MilSystem Setup Table 7.
MilSystem Setup Table 8. MC-2 Connector Pin Signals (Continued) 12 Pin # Breakout Cable Connector Breakout Cable Pin # Signal Signal Description 54 Ethernet SH SHIELD Ethernet0, 1, 2, 3 Shield 18 Serial 1 1 DCD1 Indicates external serial device is detecting a carrier signal. 19 Serial 1 2 RXD1 Receive Data 20 Serial 1 3 TXD1 Transmit Data 21 Serial 1 4 DTR1 Indicates port is powered, initialized, and ready.
MilSystem Setup Table 8. MC-2 Connector Pin Signals (Continued) Pin # Breakout Cable Connector Breakout Cable Pin # Signal Signal Description 45 Serial 4 1 DCD4 Indicates external serial device is detecting a carrier signal. 46 Serial 4 2 RXD4 Receive Data 47 Serial 4 3 TXD4 Transmit Data 48 Serial 4 4 DTR4 Indicates port is powered, initialized, and ready. 49 Serial 4 5 GND4 Ground 50 Serial 4 6 DSR4 Indicates external serial device is powered, initialized, and ready.
MilSystem Setup Table 9. MC-3 Connector Pin Signals (Continued) 14 Pin # Breakout Cable Connector Breakout Cable Pin # Signal Signal Description 13 Parallel 13 SLCT Select - indicates the printer is selected and powered on if the signal state is High. 14 Parallel 14 AFD Auto Feed - requests the printer to automatically feed one line after each line is printed.
MilSystem Setup Table 9.
MilSystem Setup Applying Power to the MilSystem 8) Follow these steps to apply power to the MilSystem. AD C 8-4 B 17 10 4 1 25 32 40 47 3 53 9 PO W • Connect the AC Mating Cable to the AC Adapter (options.) See Figure 1 on page 5. • Plug in the DC Cable Connector from the AC Adapter (option) to the DC IN jack on the MilSystem. See Figure 3 on page 8.
MilSystem Setup 10) Using the Operating System (OS) MilSystem • You should see a prompt on the monitor screen indicating the OS is loading, or has loaded. • Refer to the respective OS manual (not supplied by ADLINK.) • Refer to the LittleBoard 735, LittleBoard 800, or COM 840 Support Software DVDs or QuickDrives for additional drivers and instructions.
MilSystem Setup 18 User’s Guide MilSystem
Appendix A Technical Support ADLINK Technology, Inc. provides a number of methods for contacting Technical Support listed in the Table A-1 below. Requests for support through the Ask an Expert web page are given the highest priority, and usually are addressed within one working day. • ADLINK Ask an Expert – This is a comprehensive support center designed to meet all your technical needs. This service is free and available 24 hours a day through the Ampro By ADLINK web page at http://www.adlinktech.
Appendix A Technical Support Table A-1. Technical Support Contact Information (Continued) ADLINK Technology Beijing Address: ▦℻ゑ䀆䁏◉ₙ⦿₫恾 1 ⚆䥗⒪┷┪⮶☵ E ㄶ 801 ⸳(100085) Rm. 801, Power Creative E, No. 1, B/D Shang Di East Rd., Beijing, 100085 China Tel: +86-10-5885-8666 Fax: +86-10-5885-8625 Email: market@adlinktech.com ADLINK Technology Shenzhen Address: 䂀⧂ゑ◦⼀◉䱠㔏⥼◦◉浧㠿◦ₒ拢 㟿ⷦ㔏㦾⥼ A1 㪚 2 㰋 C ◉ (518057) 2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7, High-Tech Industrial Park S.
Appendix B Physical Dimensions Figure B-1 shows the MilSystem enclosure dimensions. CL 7,36" 187 mm 5.51" 140 mm CL CL 11.02" 280 mm 12.20" 310 mm 10.00" 254 mm CL 8.18" 208 mm 3.90" 99 mm (+/- 2mm) Figure B-1.
Appendix B 22 Physical Dimensions User’s Guide MilSystem
