Installation Guide

ManualsBrandsAdmiral ManualsHousehold Appliance6.5 cu. ft. Electric Dryer in White

W10514172B

W10514174A-SP

DRYER SAFETY ......................................................................... 2

INSTALLATION REQUIREMENTS ............................................. 4

Tools and Parts ...................................................................... 4

Location Requirements ......................................................... 5

Electrical Requirements ........................................................ 6

Install Leveling Legs .............................................................. 7

Electrical Connection ............................................................ 7

VENTING ................................................................................... 13

Venting Requirements ......................................................... 13

Plan Vent System ................................................................. 14

Venting Kits .......................................................................... 14

Install Vent System .............................................................. 16

Connect Vent ........................................................................ 16

Level Dryer ........................................................................... 16

Complete Installation Checklist ......................................... 16

Reverse Door Swing (Optional) .......................................... 17

Troubleshooting ................................................................... 19

ELECTRIC DRYER INSTALLATION INSTRUCTIONS

29" WIDE MODELS - U.S.A. ONLY

Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite:

www.whirlpool.com

Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta.

Table of Contents

Summary of content (20 pages)

PAGE 1
ELECTRIC DRYER INSTALLATION INSTRUCTIONS 29" WIDE MODELS - U.S.A. ONLY Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite: www.whirlpool.com Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta. Table of Contents DRYER SAFETY ......................................................................... 2 INSTALLATION REQUIREMENTS .............................
PAGE 2
DRYER SAFETY 2
PAGE 3
PAGE 4
INSTALLATION REQUIREMENTS Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed: Level Caulking gun and compound (for installing new exhaust vent) Parts supplied (all models): Flat-blade screwdriver #2 Phillips screwdriver Leveling legs (4) Wire stripper (direct wire installations) Tin snips (new vent installations) Parts package is located in dryer drum. Check that all parts are included.
PAGE 5
Location Requirements Minimum spacing for recessed area or closet installation The dimensions shown following are for the minimum spacing allowed. ■■ Additional spacing should be considered for ease of installation and servicing. ■■ Additional clearances might be required for wall, door, and floor moldings. ■■ Additional spacing of 1" (25 mm) on all sides of the dryer is recommended to reduce noise transfer.
PAGE 6
Electrical Requirements It is your responsibility: ■■ To contact a qualified electrical installer. ■■ To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and ordinances. The National Electrical Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations.
PAGE 7
Install Leveling Legs Electrical Connection Power Supply Cord 1. Prepare dryer for leveling legs To avoid damaging floor, use a large flat piece of cardboard from dryer carton; place under entire back edge of dryer. Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboard. 2. Electrical Connection Options Screw in leveling legs diamond marking Examine leveling legs, find diamond marking.
PAGE 8
Direct Wire Power Supply Cord Connection Power supply cord strain relief 1. Attach power supply cord strain relief A B C D Remove the screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections (C) into the hole (B) below the terminal block opening so that one tab is pointing up (A) and the other is pointing down (D), and hold in place. Tighten strain relief screws just enough to hold the two clamp sections (C) together. 2.
PAGE 9
4-wire Power Supply Cord Connection 5. Connect ground wire IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. B A C A. B. C. D. E. F. G. 3. A F E D G 4-wire receptacle (NEMA type 14-30R) 4-prong plug Ground prong Neutral prong Spade terminals with upturned ends 3/4" (19 mm) UL listed strain relief Ring terminals Prepare to connect neutral ground wire and neutral wire.
PAGE 10
2. Attach direct wire cable to 4. Connect neutral wire B strain relief C Connect neutral wire (white or center) (C) of power supply cord to center terminal block screw (B). Tighten screw. 5. Connect remaining wires Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screws. For 3-wire Direct Wire Connection, see page 11. For 4 wire Direct Wire Connection, continue to step 3 below.
PAGE 11
5. Prepare to connect neutral ground wire and neutral wire 8. Connect remaining wires A B E Remove center terminal block screw (B). Remove neutral ground wire (E) from external ground conductor screw (A). 6. Connect neutral ground wire and neutral wire Place hooked ends of remaining direct wire cable wires under outer terminal block screws (hooks facing right). Squeeze hooked ends together and tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel.
PAGE 12
2. Connect neutral ground wire 6. Connect neutral wire and neutral wire B B C C Place hooked end of neutral wire (white or center) (C) of direct wire cable under center terminal block screw (B). Squeeze hooked end together. Tighten screw. E Connect neutral ground wire (E) and neutral wire (white or center wire) (C) of power supply cord or cable under center terminal block screw (B). Tighten screw. 7. Connect remaining wires 3.
PAGE 13
VENTING Venting Requirements Exhaust hoods: ■■ Must be at least 12" (305 mm) from ground or any object that may obstruct exhaust (such as flowers, rocks, bushes, or snow). Recommended Styles: Louvered hood Box hood Acceptable Style: WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. Dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building.
PAGE 14
Alternate installations for close clearances Plan Vent System Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer’s instructions. Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer. Other installations are possible. B C D E F A G B Over-The-Top installation (also available with one offset elbow) H A. B. C. D. Dryer Elbow Wall Exhaust hood E. F. G. H.
PAGE 15
Special provisions for mobile home installations: The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside. Determine vent path: ■ Select route that will provide straightest and most direct Vent System Chart (Long Vent Models Only) Number of 90° turns or elbows Type of vent Box/louvered, or Angled hoods 0 Rigid metal 120 ft. (36.6 m) 1 Rigid metal 110 ft. (33.
PAGE 16
Connect Vent NOTE: The dryer must be level for the moisture sensing system to operate correctly. 1. Connect vent to exhaust outlet Not Level LEVEL Not Level 2. Tighten and adjust leveling legs Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check that vent is secured to exhaust hood with a 4" (102 mm) clamp. 2.
PAGE 17
❑ When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close the door. 3. Lift door off top screws If you do not feel heat, turn off dryer, and check the following: ■ There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician.
PAGE 18
6. Switch door catch, bezel, & plug Catch and bezel 8. Flip door over Plug Flip door over so handle side is down. 9. Attach door hinges Remove the door catch, bezel, and plug from the inside of the inner door by squeezing and pulling/pushing them. Place the door catch, bezel, and plug on the sides opposite from where they were. 7. Rotate outer door Rotate outer door 180º and set it back down on inner door.
PAGE 19
10. Remove door strike and door strike plug Door strike Insert screws in hinge holes on dryer cabinet Door strike plug Remove door strike and door strike plug from dryer cabinet. Insert the door strike into door strike plug hole and secure with screw. Insert door strike plug into original door strike hole and secure with screw. 11. 12. Remove and transfer hinge hole plugs NOTE: Two people may be needed to reinstall door. Insert screws into the bottom holes on left side of dryer cabinet.