Instructions / Assembly

ManualsBrandsAdmiral ManualsHousehold Appliance6.5 cu. ft. Electric Dryer in White

W10096987A

W10097001A-SP

DRYER SAFETY ......................................................................... 2

INSTALLATION REQUIREMENTS ............................................. 2

Tools and Parts ...................................................................... 2

Location Requirements ......................................................... 3

Electrical Requirements ........................................................ 4

Install Leveling Legs .............................................................. 5

Electrical Connection ............................................................ 6

VENTING ................................................................................... 12

Venting Requirements ......................................................... 12

Plan Vent System ................................................................. 13

Venting Kits .......................................................................... 13

Install Vent System .............................................................. 14

Connect Vent ........................................................................ 15

Level Dryer ........................................................................... 15

Complete Installation Checklist ......................................... 15

Reverse Door Swing (Optional) .......................................... 16

Troubleshooting ................................................................... 19

ELECTRIC DRYER INSTALLATION INSTRUCTIONS

29" WIDE MODELS - U.S.A. ONLY

Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite:

www.whirlpool.com

Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta.

Table of Contents

Summary of content (20 pages)

PAGE 1
Electric Dryer Installation Instructions 29" Wide Models - U.S.A. Only Para obtener acceso al manual de uso y cuidado en español, o para obtener información adicional acerca de su producto, visite: www.whirlpool.com Tenga listo su número de modelo completo. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta. Table of Contents DRYER SAFETY.......................................................................... 2 Installation Requirements..............................
PAGE 2
DRYER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.
PAGE 3
If using a power supply cord: Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain: ■■ A UL listed 30-amp power supply cord, rated 120/240 volt 1/4" nut driver (recommended) Vent clamps minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends. ■■ A UL listed strain relief.
PAGE 4
Dryer Dimensions Mobile home - Additional installation requirements This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). ■■ Metal exhaust system hardware, which is available for purchase from your dealer. ■■ Special provisions must be made in mobile homes to introduce outside air into the dryer.
PAGE 5
If using a power supply cord: Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain: Install Leveling Legs WARNING ■■ A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends. ■■ A UL listed strain relief.
PAGE 6
Electrical Connection Power Supply Cord Direct Wire WARNING WARNING Fire Hazard Fire Hazard use a new ul listed 30 amp power supply cord. Use 10 gauge solid copper wire. use a ul listed strain relief. Use a UL listed strain relief. Disconnect power before making electrical connections. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center terminal (silver). Connect neutral wire (white or center wire) to center terminal (silver).
PAGE 7
Power Supply Cord Connection Power supply cord strain relief 1. 4-wire Power Supply Cord Connection Attach power supply cord strain relief IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. A B A F B C C D Remove the screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief).
PAGE 8
5. Connect ground wire 3-wire Power Supply Cord Connection Use where local codes permit connecting cabinet-ground conductor to neutral wire. A B E D A C F Connect ground wire (F) (green or bare) of power supply cord to external ground conductor screw (A). Tighten screw. A. B. C. D. E. F. G. G F 3-wire receptacle (NEMA type 10-30R) 3-wire plug Neutral prong Spade terminals with upturned ends 3/4" (19 mm) UL listed strain relief Ring terminals Neutral (white or center wire) 3.
PAGE 9
Direct Wire Connection Direct wire strain relief 4-wire Direct Wire Connection 1. Attach direct wire strain relief A IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit 3-wire connections. 3. Prepare your 4-wire cable for direct connection B 1" C Unscrew the removable conduit connector (A) and any screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief).
PAGE 10
6. Connect neutral ground wire and neutral wire 3-wire Direct Wire Connection Use where local codes permit connecting cabinet-ground conductor to neutral wire. 3. Prepare your 3-wire cable for direct connection C 1" B m) (25 m 3½" (89 m m) E Connect neutral ground wire (E) and place hooked end (hook facing right) of neutral wire (white or center wire) (C) of direct wire cable under center screw of terminal block (B). Squeeze hooked ends together and tighten screw. 7.
PAGE 11
2. Connect neutral ground wire 6. Connect neutral wire and neutral wire B B C C E Place hooked end of neutral wire (white or center) (C) of direct wire cable under center terminal block screw (B). Squeeze hooked end together. Tighten screw. 7. Connect remaining wires Connect neutral ground wire (E) and neutral wire (white or center wire) (C) of power supply cord or cable under center, silver-colored terminal block screw (B). Tighten screw. 3.
PAGE 12
VENTING Venting Requirements WARNING Exhaust hoods: ■■ Must be at least 12" (305 mm) from ground or any object that may obstruct exhaust (such as flowers, rocks, bushes, or snow). B 4" (102 mm) A 4" (102 mm) Fire Hazard use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow these instructions can result in death or fire. WARNING: To reduce the risk of fire, this dryer MUST BE C 2½" (64 mm) 4" (102 mm) Recommended styles: A. Louvered hood B.
PAGE 13
Alternate installations for close clearances Plan Vent System Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer’s instructions. Recommended exhaust installations Typical installations vent the dryer from the rear of the dryer. Other installations are possible. B C D E F A G B Over-The-Top installation (also available with one offset elbow) H A. B. C. D. Dryer Elbow Wall Exhaust hood E. F. G. H.
PAGE 14
Special provisions for mobile home installations: The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside. Determine vent path: ■■ Select route that will provide straightest and most direct Vent System Chart (Long Vent Models Only) Number of 90° turns or elbows Type of vent Box/louvered, or Angled hoods 0 Rigid metal 120 ft. (36.6 m) 1 Rigid metal 110 ft. (33.
PAGE 15
Connect Vent NOTE: The dryer must be level for the moisture sensing system to operate correctly. 1. Connect vent to exhaust outlet Not Level LEVEL Not Level 2. Tighten and adjust leveling legs Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check that vent is secured to exhaust hood with a 4" (102 mm) clamp. 2.
PAGE 16
q When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close the door. 2. Remove bottom screws If you do not feel heat, turn off dryer, and check the following: ■■ There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician. NOTE: You may notice an odor when the dryer is first heated.
PAGE 17
5. Insert screws in hinge holes on dryer cabinet NOTE: Two people maybe needed to reinstall door. Insert screws into bottom holes on left side of dryer cabinet. Tighten screws halfway. Position door so large end of door hinge slot is over screws. Slide door up so screws are in bottom of slots. Tighten screws. Insert and tighten top screws in hinges. 2. Remove bottom screws Open dryer door. Remove bottom screws from dryer cabinet side of hinges.
PAGE 18
5. Remove screws from door 8. Attach door hinges Remove screws at top, bottom, and side of door (4 screws). Keep door screws separate from hinge screws as they are diferent sizes. Holding door over towel on dryer, grasp sides of outer door and lift to separate it from inner door. NOTE: Do not pry apart with putty knife or screwdriver. Do not pull on door seal or plastic door catches. 6. Rotate outer door Reattach door hinges to dryer door so that the larger hole is at the bottom of the hinge. 9.
PAGE 19
10. Remove and transfer 12. Remove door strike plug hinge hole plugs Use a small, flat-blade screwdriver to gently remove 4 hinge hole plugs on left side of dryer cabinet. Transfer plugs into hinge holes on opposite side of dryer cabinet. 11. Insert screws in hinge holes on dryer cabinet NOTE: Two people maybe needed to reinstall door. Insert screws into the bottom holes on left side of dryer cabinet. Tighten screws halfway. Position door so large end of door hinge slot is over screws.