Evaporative Cooler Brochure

ManualsBrandsAdobeAir ManualsHumidifierMS524

Modular Components

• Air Handling Modules in side, down or up

discharge and single or dual inlet design.

• Evaporative Media Modules with standard 8” or

Hi-Performance 12” media.

• Indirect Cooling Modules for added cooling

with no moisture added (optional).

Durable Construction

• Galvanized steel with our exclusive

POLYBOND® polyester epoxy powder

based coating ensures years of dependable

service.

Efﬁ ciency

• Choice of media modules allows cooling

efﬁ ciencies tailored to your design

requirements.

INDUSTRIAL DIRECT AND INDIRECT/DIRECT EVAPORATIVE COOLING

Engineer designed to satisfy your design requirements.

Cost Effectiveness

• Competitive ﬁ rst cost combined with substantial

energy savings over refrigerated air units results in

quick payback. Plus, the simplicity of design allows

low maintenance requirements.

Other Features

• Precision balanced blower wheel.

• Solid shaft for rugged durability.

• AdobeAir motors and pumps are U.L. Recognized.

• City of Los Angeles (C.O.L.A.) approved.

• AMCA Licensed ratings

• U.L. Classiﬁ ed

• U.L. Listed

Dual Inlet

Models MD628, MS628, and MU628 U.L. Classified

Shown with 12” media modules DM120

Models UD980 and US980 U.L. Listed

Shown with 12” media modules UM120

Single Inlet

Models MD524 and MS524 U.L. Classified

Shown with 12” media modules DM080

Models UD960 and US960 U.L. Listed

Shown with 12” media modules UM080

AdobeAir, Inc. certifies that the evaporative air cooling products

shown herein are licensed to bear the AMCA Seal. The ratings

shown are based on tests and procedures performed in

accordance with AMCA Publication 211 and comply with the

requirements of the AMCA Certified Ratings Program.

Summary of content (8 pages)

PAGE 1
INDUSTRIAL DIRECT AND INDIRECT/DIRECT EVAPORATIVE COOLING Engineer designed to satisfy your design requirements. Modular Components Cost Effectiveness • Air Handling Modules in side, down or up discharge and single or dual inlet design. • Competitive first cost combined with substantial energy savings over refrigerated air units results in quick payback. Plus, the simplicity of design allows low maintenance requirements. • Evaporative Media Modules with standard 8” or Hi-Performance 12” media.
PAGE 2
SINGLE-STAGE INDUSTRIAL EVAPORATIVE COOLING Direct Evaporative Cooling Process MasterCool Evaporative Media Direct evaporative cooling exchanges sensible heat for latent heat, and follows upward along a constant wet-bulb temperature line on the Psychrometric Chart. The result is a dry-bulb temperature of the leaving air (B) approaching the wet-bulb temperature of the entering air (A).
PAGE 3
2-STAGE INDUSTRIAL EVAPORATIVE COOLING Indirect/Direct Evaporative Cooling Process The Indirect Cooling Module In the indirect cooling stage, entering air is cooled along a horizontal humidity ratio line on the Psychrometric Chart (A to B) without adding moisture. In the next cooling stage, this air is further cooled along a new wet-bulb line (B to C), resulting in a lower dry-bulb temperature of leaving air than can be achieved with single stage direct evaporative cooling alone.
PAGE 4
DIMENSIONS AND SPECIFICATIONS Single Inlet Model Dimensions MD524 or UD960 (Down Discharge) and MS524 or US960 (Side Discharge) Top View Side View Front View MD/MS524 or UD/US960 Media SectionCabinet Model Number 1 Required H W Drain1 Location Duct Location Side D A DM080 or UM080 51½ 491/8 66 DM120 or UM120 51½ 491/8 70 Down C E B F G Media Blower Cabi- Cabinet net J K Water2 Service Location L M Electric3 Service Location S T Dia. Width Blower Skid Location Pulley Pitch Shaft Dia.
PAGE 5
Dual Inlet Model Dimensions MD628 or UD980 (Down Discharge), MS628 or US980 (Side Discharge) and MU628 (Up Discharge) Top View Side View - Blower Section Front View (UP) (DOWN) MD/MS/MU628 or UD/US980 Media Section Model Number 1 Required H Cabinet Duct Location Side W D DM080 or UM080 51½ 831/8 491/8 DM120 or UM120 51½ 911/8 491/8 A B Drain1 Location Down C E F G Media Blower Cabi- Cabinet net J K Water2 Service Location L M Electric3 Service Location S T Dia.
PAGE 6
DIMENSIONS Certified Air Delivery CFM at Various External Static Pressures Inches Water Gauge. AMCA Licensed Ratings.
PAGE 7
.3 CFM .3 RPM .4 CFM .4 RPM .5 CFM .5 RPM .6 CFM .6 RPM .7 CFM .7 RPM .8 CFM .8 RPM .9 CFM .9 RPM 1.0 CFM 1.
PAGE 8
Project Submittal Sheet Models MD/MS 524, MD/MS/MU 628 — U.L. Classified or UD/US 960, UD/US 980 — U.L. Listed Project SHL* Location Architect Engineer Contractor Submitted By Date *Total design sensible heat load of project. Blower Section – Motor – Motor Sheave – Pulley and Belt Kit Ref. No. Blower Section Qty. Model No.