install guide FLC-IDS(RS)-BM1-EN Document number Revision Date 20130523 fiRmware FLC-IDS(RS)-BM1 hardware FLRSBM1 accessories PROGRAMMING CABLE FLPROG (REQUIRED) FLRF1/2 (OPTIONAL) CARLINK ASCL2 (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician.
Page 2 of 15 • 20130523 VEHICLE LIST - 1 OF 1 FEATURES REMOTE START FROM OEM REMOTES SECURE TAKEOVER** DATA IMMOBILIZER BYPASS ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE PARKING LIGHT CTRL RAP SHUTDOWN CTRL TACHOMETER STATUS MONITORING BRAKE PEDAL STATUS MONITORING VSS STATUS MONITORING DOOR STATUS MONITORING TRUNK STATUS MONITORING HOOD STATUS MONITORING* 08-13 1 • • • • • • • • • • • • • • • • • 3 Series PTS AT 06-11 1 •
Page 3 of 15 • 20130523 BOX CONTENTS - 1 OF 1 BOX CONTENTS MODULE LED 1 M N 10 PIN WHITE CONNECTOR T-HARNESS 1 LED 2 L K PROGRAMMING BUTTON A 12 PIN BLACK CONNECTOR J I B H C G AFTERMARKET HOOD SWITCH AND CABLE D E F T-HARNESS 2 EXPANSION PACK XP LED 1 STICKER 1 XP LED 2 O STICKER 2 EXPANSION CABLE P ACCESSORIES (SOLD SEPARATELY) RF KIT (OPTIONAL) PROGRAMMING CABLE (REQUIRED) COMPATIBLE MODELS ONLY TELEMATICS DEVICE (OPTIONAL) COMPATIBLE MODELS ONLY Automotive Data Solutions Inc
Page 4 of 15 • 20130523 MODULE INSTALLATION PROCEDURE - 1 OF 1 01 02 START vehicle. Verify all vehicle functionalities. If the vehicle displays error messages or any malfunction: stop the installation and service the vehicle. 07 Turn ignition to OFF position. Remove keyfob from keyport. 08 Connect and secure every connector to the vehicle, as shown in STEP 1 of the WIRING DIAGRAM. 13 Connect the P connector to the module, as shown in STEP 3 of the WIRING DIAGRAM.
Page 5 of 15 • 20130523 TYPE 1 - WIRING DIAGRAM - 1 OF 1 STEP 1: CONNECT THE FOLLOWING TO THE VEHICLE START THE VEHICLE WITH THE OEM KEYFOB TO TEST THE CONNECTIONS MODULE N M L K J I H G O A B C WARNING 1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4 2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1 A1 D BRAKE SWITCH 4 3 2 1 A1 A2 BRAKE HARNESS P E F COMFORT ACCESS SYSTEM MODULE RELAY MINI: BEHIND INSTRUMENT PANEL, DRIVER SIDE BMW: UNDER DASH, DRIVER SIDE STEP 2: CONNECT THE FOLLOWING TO THE MOD
Page 6 of 15 • 20130523 MODULE PROGRAMMING PROCEDURE - 1 OF 1 01 LED 1 is solid RED. Insert keyfob 1 into keyport. 07 Remove keyfob 1 from keyport. 13 LED 1 will turn solid GREEN for 2 seconds. 02 Within 10 seconds, LED 1 will flash GREEN once (1x). 08 WARNING: Follow steps 4, 3, 2 as shown in the wiring diagram to disconnect the module from the vehicle. 14 Remove keyfob 1 from keyport. 03 Remove keyfob 1 from keyport. 09 Connect module to computer and proceed with KLON programming.
instaLLation checKList - 1 OF 2 Page 7 of 15 • 20130523 checKList 01 WARNING: Vehicle engine will start many times. Test in a well ventillated area. 02 Open driver door window for easy vehicle access. 03 Close all vehicle doors, hood and trunk. 04 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 1: Does the vehicle remote start? YES: Go to step 5. 05 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
instaLLation checKList - 2 OF 2 Page 8 of 15 • 20130523 checKList 19 Close all doors. 20 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. 21 Wait for the vehicle to start. Question 8: Is the vehicle equipped with Comfort Access System ? YES: Touch exterior driver door handle to unlock door using Comfort Access System. Within 45 seconds, go to step 22. 22 Open driver door. NO: Press UNLOCK button once [1x] on the OEM keyfob.
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1 >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 06 Remove keyfob from keyport. 01 Insert keyfob into keyport. 07 Valet Mode Programming Procedure completed. 02 Time restriction. Complete next step within 5 seconds. >> To exit valet mode: repeat steps 1 to 6.
aFteRmaRKet Remote PRogRamming - 1 OF 1 Page 10 of 15 • 20130523 FLC-IDS(RS)-BM1-EN www.flashlogic.com aFteRmaRKet Remote PRogRamming: notes I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures. Automotive Data Solutions Inc.
Page 11 of 15 • 20130523 MODULE NAVIGATION PROCEDURE - 1 OF 1 >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 13. 04 >> Module must be programmed to the vehicle. 05 >> Use the Module Navigation Chart on the next page. 06 Set ignition to OFF position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid GREEN.
Page 12 of 15 • 20130523 [Y] oPtions [X] menus moDuLe navigation chaRt: notes I Default settings are listed in bold.
[X] numbeR oF PaRKing Light FLashes Diagnostic Remote staRteR eRRoR coDes - 1 OF 1 I WARNING: The following applies only when the parking lights are connected and supported by the system. 03 Foot brake is ON. 04 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 05 Engine tach signal is lost. 06 System is in Valet Mode. 07 Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized.
I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Automotive Data Solutions Inc. © 2013 Diagnostic test moDuLe LeD 1 status moDuLe Diagnostics - 1 OF 1 Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then OFF Module correctly programmed. OFF No activity or module already programmed.
MODULE RESET PROCEDURE - 1 OF 1 01 Disconnect all connectors from module except the BLACK 20-PIN connector. 07 Reconnect all connectors. 02 Disconnect the BLACK 20-PIN connector. 08 Repeat programming procedure. 03 PRESS AND HOLD programming button while connecting the BLACK 20-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED 1 will flash RED. RELEASE programming button. 05 LED 1 will turn RED for 2 seconds.
