ADT Video Doorbell Quick Installation Guide FCC ID: P27DBC845 ADT Pulse® Interactive Solutions DBC845 FHD Wireless Doorbell Camera Property of ADT, LLC. Information accurate as of published date and is provided “as is” without warranty of any kind. ©2017ADT LLC dba ADT Security Services. All rights reserved. ADT, the ADT logo, 800 ADT.ASAP and the product/service names listed in this document are marks and/or registered marks. Unauthorized use is strictly prohibited.
ADT Video Doorbell Quick Installation Guide INTRODUCTION 1 Introduction This section provides information about the Doorbell Camera features, components and capabilities. Packaging Contents The following items are included in the package. 1. Doorbell Camera x 1 2. Two Mounting Brackets (Small Slim & Gang Plate size) 3.
ADT Video Doorbell Quick Installation Guide INTRODUCTION 4. (No.1) Screw/Anchor x 2 5. (No.2) Screw x 2 6. (N0.3) Screw x 2 7. (No.4) Screw x 2 8. Bubble Level 9.
ADT Video Doorbell Quick Installation Guide INTRODUCTION Physical Details The DBC845 supports both analog and digital chimes within 8-24 AC voltage range. The operation temperature is –4°F to 122°F.
ADT Video Doorbell Quick Installation Guide INTRODUCTION Overview Doorbell/WPS Button has two functions: WPS Pin Code Mode: When pressed and held 5 seconds, the doorbell camera will be in WPS Pin Code Mode. Note: When Wi-Fi connection is established, the WPS function is disabled. Doorbell Mode: Press the button to ring the door chime.
ADT Video Doorbell Quick Installation Guide FW download In Progress 6 Green Medium Factory Reset Red Medium No Power Dark N/A Spinning INTRODUCTION Spinning will indicate FW being downloaded. Once complete, update takes place and doorbell reboots.
ADT Video Doorbell Quick Installation Guide BASIC SETUP 2 Basic Setup This section provides information on how to assemble and configure the DBC845 Doorbell Camera for enrollment. Installation 1. Power-Up and Check LED Turn on the switch on the rear side of the doorbell camera and wait for 20 seconds until the LED turns to flashing red. Note: The internal battery supports about 40 minutes of operation.
ADT Video Doorbell Quick Installation Guide ADT PULSE ENROLLAMENT 3 ADT Pulse Enrollment This section provides instructions for wirelessly enrolling the DBC845 Doorbell Camera into the ADT Pulse network. This process uses WiFi Protected Setup (WPS) with PIN method to wirelessly enroll the HD Camera to gateway via the ADT Pulse portal or Installer App. Using WPS with PIN 1. Power up the camera and wait for the LED to turn flashing red, as described in the previous chapter. 2.
ADT Video Doorbell Quick Installation Guide ADT PULSE ENROLLMENT 5. Click the Add Using WPS button at the bottom of screen as shown in Figure 3-2. Figure 3-2 Clicking Add Using WPS Button 6. Locate the camera PIN number on the label on the rear of the camera. Enter the PIN number in the WPS PIN field as shown in Figure 3-3.
ADT Video Doorbell Quick Installation Guide ADT PULSE ENROLLAMENT 7. Click the Continue button to initiate the WPS process. Figure 3-4 Clicking "Continue" Button 8. Press the doorbell button, the LED will blink green during WPS process. Note: This WPS process must be completed within 2 minutes or else it will be timed out. The remaining time is displayed in the upper left portion of the screen.
ADT Video Doorbell Quick Installation Guide ADT PULSE ENROLLMENT 9. Once the doorbell camera is enrolled, the Camera Details screen will be displayed. Name the device and select the desired bandwidth & chime type. Click Save after entering or change settings. Figure 3-6 Saving Camera Details 10. The newly added device will be shown in the Camera List, then click Go Back at the top left of the screen as shown in Figure 3-7.
ADT Video Doorbell Quick Installation Guide ADT PULSE ENROLLAMENT 11. The Manage Devices screen is displayed, click Close. Figure 3-8 Manage Devices Screen 12. Click System page to verify the device enrollment. Figure 3-9 System Screen 13. Move the doorbell to where it will be mounted and check the LED and site diagnostics to verify Wi-Fi signal strength. Note: If the Wi-Fi cannot reach the doorbell camera, you will see the LED blinking red.
ADT Video Doorbell Quick Installation Guide ADT PULSE ENROLLMENT 14. Factory Reset Instructions: A. Press the doorbell button to wake up the device B. If already enrolled, the device will “ding-dong” C. If not already enrolled, the device will go into WPS mode and blink green D. Press and hold the reset button on the back until you hear a ring (about 10 seconds), then release to start the reset process E.
ADT Video Doorbell Quick Installation Guide HARDWARE INSTALLATION 4 Hardware Installation This section provides details for mounting the DBC845 Doorbell Camera. Installing Hardware Note: Ensure the camera is configured and enrolled in ADT Pulse before permanently mounting. 1. Turn off the breaker circuit before disconnecting legacy doorbell button. Figure 4-1 Breaker Circuit 2. Unscrew the legacy doorbell to locate two power wires. (The recommended installation height is between 47 -60 inches.
ADT Video Doorbell Quick Installation Guide HARDWARE INSTALLATION Note: Check the voltage at the doorbell to ensure voltage is between 9 ~ 24 VAC. If the voltage is DC, then the DC845 does not support this voltage type.
ADT Video Doorbell Quick Installation Guide HARDWARE INSTALLATION 3. Choose the mounting bracket that will cover the hole of the legacy doorbell button. The larger bracket should be used with gang boxes. Figure 4-3 Choosing Mounting Bracket 4. Connect the power wires from the existing doorbell to the screw terminals of the bracket.
ADT Video Doorbell Quick Installation Guide HARDWARE INSTALLATION 5. Secure the bracket with screws (No. 1 or No. 2). Please see Figure 4-5. Note: Install the anchors if necessary. Figure 4-5 Installing the Screws 6. Attach the doorbell camera to the mounting bracket. Make sure the doorbell camera is firmly fixed and working properly. Caution: To avoid damaging the rubber seal of the pogo pins, please attach the camera to the mounting bracket flush. Mounting bracket should lay flat against the wall.
ADT Video Doorbell Quick Installation Guide HARDWARE INSTALLATION Using the Wedge Kit (Optional) If needed, you can mount your doorbell at an angle for better view and motion detection. The wedge kit comes with 3 plates which can be used to tilt the camera forward or sideways by 15/30 degrees. 1. Use the two screws (No.1) to install the wedge into the wall. The larger bracket should be used with gang box. Figure 4-7 Install the Wedge 2. Secure the bracket to the wedge with the two screws (No.3 or No.
ADT Video Doorbell Quick Installation Guide HARDWARE INSTALLATION 3. Attach the doorbell camera to the bracket. Figure 4-9 Attaching the Camera to the Bracket 4. Apply the Audio Video Surveillance Sticker.
ADT Video Doorbell Quick Installation Guide HARDWARE INSTALLATION Always On Bracket Installation The Always On bracket can only be installed with mechanical doorbell chimes (AC16V~24V). In this configuration, the doorbell camera will be in always on mode, which brings back the 5 second pre-buffer, connects live view faster, and removes the need for the internal battery to be charged. 1. Choose the mounting bracket that will cover the hole of the legacy doorbell button.
ADT Video Doorbell Quick Installation Guide HARDWARE INSTALLATION 3. Secure the bracket with screws (No.1 or No.2). Please see Figure 4-13. Note: Install the anchors if necessary. Figure 4-13 Installing the Screws 4. Attach the doorbell camera to the mounting bracket. Make sure the doorbell camera is firmly fixed and working properly. Caution: To avoid damaging the rubber seal of the pogo pins, please attach the camera to the mounting bracket flush. Mounting bracket should lay flat against the wall.
ADT Video Doorbell Quick Installation Guide APPENDIX 5 Appendix Product Spec Wireless Doorbell Camera Model DBC845 Dimensions (H x W x D) 121.15 x 42.25 x 30.8mm Operating Temperature Mounting Bracket and Battery Pack mode: -20°C to 50°C Always On Bracket mode: -20ºC to 40ºC ( Day Mode) -20ºC to 35ºC ( Night Mode) Storage Temperature -20° C to 45° C Network Protocols TCP/IP, HTTP, HTTPS, DHCP, uPnP, NTP, RTP, RTCP, RTSP, DN Wireless 802.
ADT Video Doorbell Quick Installation Guide APPENDIX Regulatory Approvals FCC Statement (US) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ADT Video Doorbell Quick Installation Guide APPENDIX IC Statement (Canada)) This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
