ADT Interactive Solutions: Control & Pulse OC845 Wireless FHD Outdoor Camera Quick Installation Guide
ADT OC845 FHD Outdoor Camera Quick Installation Guide Table of Contents 1 Introduction .................................................................................3 1.1 Feature Overview ................................................................ 3 1.2 Physical Details: Front and Rear Panels ........................... 4 1.3 Packaging Contents ............................................................ 5 2 Basic Setup ............................................................................
ADT OC845 FHD Outdoor Camera Quick Installation Guide 1 Introduction This section provides information about the OC845 Outdoor Day/Night FHD Camera's features, components and capabilities. 1.1 Feature Overview The OC845 is an Outdoor day/night camera with FHD resolution and 802.11ac Wi-Fi connectivity intended for use with both ADT Control® and Pulse®. • Standalone Design. The camera is a standalone system with built-in CPU and video encoder.
ADT OC845 FHD Outdoor Camera Quick Installation Guide 1.2 Physical Details: Front and Rear Panels Component DC Power Jack Description Connect the supplied 12V power adapter. Do not use other power adapters; doing so may damage the camera. Tri-Color LED Indicator for Off: Unit does not have power On: (Blue) Unit is booting up then LED will blink blue ten Power/Network/WPS times Blinking: (Green/Amber) The power LED will blink green/amber after initial startup is completed.
ADT OC845 FHD Outdoor Camera Quick Installation Guide PIR Sensor Microphone Speaker Micro SD Card Slot This is a Passive Infrared Sensor to detect motion Built-in Microphone with echo cancelation Built-in Speaker (1W) Built-in Micro SD Card Slot for future enhancements Note: As the microSD card slot is not currently functional, please do not remove this protective cover. 1.
ADT OC845 FHD Outdoor Camera Quick Installation Guide Caution: Use the power adapter provided. Using a different power adapter may result in hardware damage. 2.3 Final Steps • Check LED Status - The LED lights up solid blue then blinks ten times during startup, which takes about 30 seconds. After startup is completed, and prior to enrollment, the power LED blinks green/amber. • Enroll the Camera - The process for enrolling the camera on Control is described in Section 3: ADT Control Enrollment.
ADT OC845 FHD Outdoor Camera Quick Installation Guide • Connect to the camera’s network SSID using a laptop or mobile device. The SSID is the model number of the camera and part of the MAC address. For example, SSID = OC845 (XX:XX:XX). • Open a web browser (IE, Chrome, Firefox, etc.). Type in adt1.com and you will be directed to the install wizard page. • Choose a language. • Click Scan for Wi-Fi Networks and select the Customer’s router SSID.
ADT OC845 FHD Outdoor Camera Quick Installation Guide • Enter the wireless credentials and click Save. • The LED will turn solid green when data is being transmitted indicating that the connection to the Customer’s router is complete. • Connect a laptop or mobile device to the Customer’s network and log in to the Control web portal, https://www.adt.com/control-login, to complete the setup. • Select Video from the menu list. • Click Settings and select Add Video Device.
ADT OC845 FHD Outdoor Camera Quick Installation Guide 4 ADT Pulse Enrollment This section provides instructions for wirelessly enrolling the OC845 Outdoor FHD Camera into the ADT Pulse network. This process uses the Wi-Fi Protected Setup (WPS) with PIN method to wirelessly enroll the FHD Camera to the gateway via the ADT Pulse Portal or TS Installer App. 4.1 Using WPS PIN to Enroll Camera • Set up the camera as described in Section 2.
ADT OC845 FHD Outdoor Camera Quick Installation Guide • Locate the camera’s PIN number on the product label on the rear of the camera. • Enter the camera’s PIN into the WPS PIN field. • Ensure that the camera is powered on and that the LED is flashing green/amber.
ADT OC845 FHD Outdoor Camera Quick Installation Guide • Click the Continue button to initiate the WPS process. The following screen appears. • Press and hold the WPS/Reset button on the camera for 5 seconds to establish a wireless connection. • The LED flashes amber as the gateway attempts to connect to the camera. The wireless connection is successful when the LED turns solid green Note: You must complete the WPS connection within 2 minutes or else the process will timeout.
ADT OC845 FHD Outdoor Camera Quick Installation Guide • The following screen is shown while the camera is configured • When the Camera Details screen appears, showing that the camera has been enrolled, assign the OC845 a unique name (usually based on the location of the camera) in the Name field, and then click Save.
ADT OC845 FHD Outdoor Camera Quick Installation Guide • The Pulse enrollment is complete. The newly added device is shown in the Cameras list. • At the top of the screen, click Go Back. • You are returned to the Manage Devices screen. The total number of installed cameras has increased by one. • Click Close and Close again to confirm.
ADT OC845 FHD Outdoor Camera Quick Installation Guide • Wait until the LED is lit solid green, and then disconnect the camera from power. • Install the camera in its final location. - Please refer to Section 5: Wall Mounting 5 Wall Mounting This section provides details for final mounting of the OC845 Outdoor FHD Camera. You should ensure that the camera is configured and enrolled in the platform before permanently mounting it.
ADT OC845 FHD Outdoor Camera Quick Installation Guide • Connect the power cable into the back of the camera. • Insert the grommet between the camera and the power input cover. Caution: Ensure that the grommet is positioned properly to prevent water from entering the camera power input. • At the location of the power source, connect the power cable to the power adapter: • Screw the red wire onto the positive (+) terminal of the power adapter, on the left side.
ADT OC845 FHD Outdoor Camera Quick Installation Guide • Remove the retaining screw from the receptacle plate and plug the power adapter into the lower power outlet. • Insert the retaining screw through the opening at the top of the power adapter and reinstall it into the receptacle, securing the adapter to the wall. • Adjust the camera to a desired position and secure it firmly. • Verify that the camera is active on the wireless network and is recognized by the platform. 5.
ADT OC845 FHD Outdoor Camera Quick Installation Guide The OC845 uses a smart IR function for night viewing. This means that the camera automatically adjusts the IR light output and gain. As a result, if any objects are in the close foreground of the image, the camera lowers the IR light output to prevent overexposing those objects. The drawback of the smart IR function is that this feature causes background objects to receive less IR light and to be displayed with lessened detail.
ADT OC845 FHD Outdoor Camera Quick Installation Guide 7 Appendix 7.1 Technical Specifications Sensor and Lens Image Sensor Minimum Illumination Lens FoV (Field-of-View) PIR Sensor 1/2.8” 2.1MP, HDR CMOS Senor 0 Lux (with IR LED On) Diagonal Viewing Angle: 145° LDC Enabled, FoV:130.3°(D), 123°(H), 81.4° (V) Detection Range: 16 feet (5 meters) Video Video Compression Video Streaming Image Settings Resolution & Frame Rate H.264 Main Profile L4.1, M-JPEG Simultaneous, H.
ADT OC845 FHD Outdoor Camera Quick Installation Guide 7.2 Regulatory Approvals 7.2.1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ADT OC845 FHD Outdoor Camera Quick Installation Guide 7.2.2 Industry Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licenceexempt RSS(s).
