SDS

ManualsBrandsAdtech ManualsAdhesivesThe Hot Glue Gun Kit with Glue Sticks

Page 1 of 5

Safety Data Sheet

SDS No. 220-99

Date of Preparation: January 12, 1999 Revised August 18, 2021

1. PRODUCT IDENTIFICATION

Product Name:

AdTech 220

Product Description:

Hot Melt Adhesive

Suggested Purpose and

Limitations:

Bonding, adhesion

Manufacturer,

Importer, Supplier:

Adhesive Technologies, Inc.

3 Merrill Ind. Dr.

Hampton, NH 03842

Taipei Hsien, Taiwan

Phone:

(603) 926-1616

Fax:

(603) 926-1780

2. HAZARD IDENTIFICATION

Toxicity Data: Conforms to ASTM D-4236 as non-toxic.

Product is non-hazardous as defined in 29 CFR 1910.1200

GHS Label: None

Label Content: Symbol: None

Warnings: None

Hazard Warning Message: None

Hazard Prevention Measure: None

Other Hazards: Touching adhesive directly while melting by heat will

cause contact burns.

3. COMPOSITION AND INFORMATION ON INGREDIENTS

Substance Name

CAS No.

Concentration

(%)

Ethylene Vinyl Acetate

Copolymers

24937-78-8

70-90%

Hydrogenated

Hydrocarbon Resin

69430-35-9

0-20%

Petroleum Resin

64742-16-1

0-20%

Petroleum Resin

68132-00-3

0-20%

Hydrocarbon Resin

62258-49-5

0-20%

Summary of content (5 pages)

PAGE 1
Safety Data Sheet SDS No. 220-99 Date of Preparation: January 12, 1999 Revised August 18, 2021 1. PRODUCT IDENTIFICATION Product Name: AdTech 220 Product Description: Suggested Purpose and Limitations: Hot Melt Adhesive Bonding, adhesion Manufacturer, Importer, Supplier: Adhesive Technologies, Inc. 3 Merrill Ind. Dr. Hampton, NH 03842 Taipei Hsien, Taiwan Phone: (603) 926-1616 Fax: (603) 926-1780 2. HAZARD IDENTIFICATION Toxicity Data: Conforms to ASTM D-4236 as non-toxic.
PAGE 2
Antioxidant Hazardous Ingredients 6683-19-8 None 0.02-2% 4. FIRST-AID MEASURES Emergency and First Aid Procedures Ingestion: Inhalation: Ingestion is not a likely route of exposure. Small amounts are not anticipated to be harmful. Seek medical attention Skin Contact: If symptomatic, move to fresh air. Seek medical attention if symptoms persist. Hot molten adhesive will adhere to and burn skin upon contact. Immediately immerse affected area in cold or ice water.
PAGE 3
8. EXPOSURE CONTROLS – PERSONAL PROTECTION Engineering Control: Local ventilation recommended when handling. Control Parameters: Time weighted average for 8-hour shift (TWA) – No data Short Term Exposure Limit (STEL) – No data Ceiling – No data Biological Exposure Index (BEI) – No data Respiratory Protection: Though the smoke and odor generated by hot melting glue is not toxic, each person has different sensitivity tolerances, it is recommended to wear a mask.
PAGE 4
Hazardous Decomposition Products: Thermal oxidative decomposition of AdTech 220 can produce carbon monoxide and /or carbon dioxide. 11. TOXICOLOGICAL INFORMATION Exposure Approach: None Symptoms: None Acute ToxicityInhalation: Inhalation of dust and smoke will stimulate the respiratory system. Skin: None Eyes: None LD50(testing animal’s absorbtion approach): 500mg/24hr (rabbit, skin) – No Data 20mg/24hr (rabbit, eyes) – No Data Chronic Toxicity or Long-Term Toxicity: None 12.
PAGE 5
Special Transport Way and Note: Not Regulated 15. REGULATORY INFORMATION EPA Regulations: RCRA Hazardous Waste Number: RCRA Hazardous Waste Classification: CERCLA Hazardous Substance (40 CFR 302.4): CERCLA Reportable Quantity (RQ): SARA 311/312 Codes: SARA Toxic Chemical (40 CFR 372.65): SARA EHS (Extremely Hazardous Substance) (40 CFR 355): OSHA Regulations: Air Contaminant (29 CFR 1910.1000, Table Z1, Z-1-A): OSHA Specifically Regulated Substance (29CFR 1910): State Regulations: Not applicable.