TSU 600 & TSU 600e User Manual Part Numbers 1202076L1 1202076L1#DC 1202076L2 1202076L2#DC October 1998 61202076L1-1C
Trademarks: Windows is a registered trademark of Microsoft Corp. T-Watch is a trademark of ADTRAN, Inc. SLC96 is a registered trademark of AT&T 901 Explorer Boulevard P.O. Box 140000 Huntsville, AL 35814-4000 Phone: (256) 963-8000 © 1998 ADTRAN, Inc. All rights reserved. Printed in USA.
YEAR 2000 Compliance All ADTRAN transmission hardware and software products have been tested and found to be fully compliant with the YEAR 2000 requirements. This is true for all models and revisions regardless of the date of manufacture or delivery.
FCC REGULATIONS REQUIRE THAT THE FOLLOWING INFORMATION BE PROVIDED TO THE CUSTOMER IN THIS MANUAL 1. This equipment complies with Part 68 of the FCC rules. The required label is attached to the bottom of the chassis. 2. An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. See installation instructions for details. 3.
FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
CANADIAN EMISSIONS REQUIREMENTS This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
CANADIAN EQUIPMENT LIMITATIONS The Industry Canada Certification label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
AFFIDAVIT REQUIREMENTS FOR CONNECTION TO DIGITAL SERVICES • An affidavit is required to be given to the telephone company whenever digital terminal equipment without encoded analog content and billing protection is used to transmit digital signals containing encoded analog content which are intended for eventual conversion into voiceband analog signals and transmitted on the network.
AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES EQUIPMENT TO 1.
( ) B. A training course provided by the customer or authorized representative, using training materials and instructions provided by the manufacturer/grantee of the equipment used to encode analog signals; or ( ) C. An independent training course (e.g., trade school or technical institution) recognized by the manufacturer/grantee of the equipment used to encode analog signals; or ( ) D.
IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, please follow these basic safety precautions to reduce the risk of fire, electrical shock, or personal injury: 1 Do not use this product near water, such as near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. 2 Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote risk of shock from lightning.
Warranty and Customer Service ADTRAN will replace or repair this product within five years from the date of shipment if the product does not meet its published specifications or if it fails while in service. For detailed warranty, repair, and return information refer to the ADTRAN Equipment Warranty and Repair and Return Policy Procedure. Return Material Authorization (RMA) is required prior to returning equipment to ADTRAN.
Table of Contents Chapter 1 Introduction .......................................................................................... 1-1 TSU 600 Overview .................................................................................................... 1-1 Product Description .......................................................................................... 1-1 Standard Features in the TSU 600................................................................... 1-2 TSU Option Modules ................
Table of Contents Set User Passcode ..................................................................................... 2-12 Set Unit Identification .............................................................................. 2-12 Set Control Port ........................................................................................ 2-13 Chain-In (PC) ............................................................................................2-13 Chain In/Chain Out ...................................
Table of Contents Internal Timing ........................................................................................... 5-6 Secondary Timing ...................................................................................... 5-7 Normal (CSU) Timing ............................................................................... 5-8 Unit Menu .......................................................................................................... 5-9 Map Exchange (Map Xchng) Menu ..................
Table of Contents Initializing the Temp Map ................................................................. 8-3 Editing the Temp Map ....................................................................... 8-4 Applying the Temp Map ................................................................... 8-4 Reviewing Maps.................................................................................. 8-4 Remote Menu Access ......................................................................................
List of Figures Figure 1-1. TSU 600 Option Modules ................................................................... 1-4 Figure 1-2. Router, PBX, Video Conferencing Application Set Up .................. 1-5 Figure 1-3. Drop and Insert, Voice, and Router Application Set Up ............... 1-6 Figure 2-1a. TSU 600 Rear Panel ............................................................................ 2-5 Figure 2-1b. TSU 600 with DC Power Rear Panel...............................................
List of Figures vi TSU 600 User Manual 61202076L1-1
List of Tables Table B-1. Table B-2. Table C-1. Table C-2. Table C-3. Table C-4. 61202076L1-1 Alarm Conditions ................................................................................. B-2 TR-08 DS0 Conversion Table .............................................................. B-3 Network Pinouts.................................................................................. C-1 Control In/Chain In Pinout ............................................................... C-2 Chain-Out Pinout .....
List of Tables viii TSU 600 User Manual 61202076L1-1
Introduction Chapter 1 TSU 600 OVERVIEW This manual covers the use of the following products: • • • • TSU 600 TSU 600 with DC power TSU 600e TSU 600e with DC power Unless otherwise stated, the TSU 600 refers to all four products. Product Description The TSU 600 is a T1/FT1 multiplexer with six option slots and embedded SNMP management. The TSU 600’s six option slots accept one of many available option modules for voice and data applications.
Chapter 1. Introduction Changes in the configuration do not disrupt data flow in channels that are not being reconfigured. The unique architecture and the availability of option modules provides a path for growth to accommodate future requirements. The TSU 600 offers a wide variety of network management options. You can manage via SNMP through the 10BaseT (600e only) or chain-in ports.
Chapter 1. Introduction TSU Option Modules Module Name Description DSX1 Short haul T1 interface for operation with a PBX (Terminal Interface). Full Drop and Insert Permits the dropping of data and insertion of new data into the same DS0 time slot. This module includes a long haul DS1 interface. It can also be used as a second DS1 interface to provide up to 3 MB aggregate throughput. Nx56/64 Serial Interface Provides a V.35 serial interface in either single or dual versions.
Chapter 1. Introduction Option Module Architecture The TSU 600 features a unique architecture that allows the addition of six option modules and plug-on boards, providing an opportunity for growth to accommodate many applications. See Figure 1-1. This unique approach allows you to mix interface types to meet any application. TSU 600 DSX-1 Module OCU-DP Module Plug on V.35 V.35 Module Plug on OCU DP D&I Module DUAL Voice Plug on Dual Voice Figure 1-1.
Chapter 1. Introduction TSU 600 CONFIGURATION APPLICATIONS The following examples illustrate possible configurations of TSU 600 applications. Router, PBX, Video Conferencing Application In this application, an Nx54/64 module provides a V.35 interface to a router. The PBX is interfaced to the TSU 600 with the DSX-1 module. An OCU DP module and OCU DP plug-on board provide two switched 56 circuits for video conferencing. The SLIP port or 10BaseT port (600e only) allows SNMP network management over the LAN.
Chapter 1. Introduction Drop and Insert, Voice, and Router Application The TSU 600 provides a router interface with an Nx56/64 module. A drop and insert module provides a second T1 interface to a remote TSU. T-WATCH PRO (which runs on a PC) easily manages the network. FXO modules are used to provide PBX extensions to remote sites. See Figure 1-3.
Installation Chapter 2 UNPACK, INSPECT, POWER UP Receipt Inspection Carefully inspect the TSU 600 for shipping damages. If you suspect damage, file a claim immediately with the carrier and then contact ADTRAN Customer Service (see the inside last page of this manual). If possible, keep the original shipping container for use in shipping the TSU 600 back for repair or for verification of damage during shipment.
Chapter 2. Installation Power Connection The AC- powered TSU 600 is equipped with a captive, 8-foot power cord, terminated by a 3-prong plug which connects to a grounded power receptacle. Power to the TSU 600 must be from a grounded 90-120 VAC, 50/ 60Hz source. DC Powered Units The DC-powered TSU 600 (1202076L1#DC or 1202076L2#DC) is equipped with a terminal strip on the rear of the unit. The power source should be connected to the terminal strip according to the polarity markings on the unit.
Chapter 2. Installation Installing and Replacing the Power Supply The following steps show how to install a new supply or replace a failed supply. Power does not have to be turned off on a working supply to add a new supply or replace a failed one. Step 1 Action One Power Supply If only one supply is installed in the chassis, remove the blank panel covering the unused power supply slot.
Chapter 2. Installation GROUNDING INSTRUCTIONS The grounding instruction information is from the Underwriters' Laboratory UL 1950, 3rd Edition. An equipment grounding conductor that is not smaller in size than the ungrounded branch-circuit supply conductors is to be installed as part of the circuit that supplies the product or system. • Bare, covered, or insulated grounding conductors are acceptable.
Chapter 2. Installation IDENTIFICATION OF REAR PANEL LAYOUT Figures 2-1a, Figure 2-1b, Figure 2-1c, and Figure 2-1d show the configuration for the rear panels of the TSU 600, TSU 600 with DC Power, TSU 600e, and TSU 600e with DC power. 1 3 2 CAUTION-RISK OF ELECTRIC SHOCK CAUTION: MAINTENANCE TO BE PERFORMED BY TRAINED SERVICE PERSONEL ONLY SUPPLEMENTAL EARTH GROUND MUST BE CONNECTED PRIOR TO CONNECTION OF TELECOMMUNICATION WIRING.
Chapter 2. Installation 1 CAUTION-RISK OF ELECTRIC SHOCK CAUTION: MAINTENANCE TO BE PERFORMED BY TRAINED SERVICE PERSONEL ONLY SUPPLEMENTAL EARTH GROUND MUST BE CONNECTED PRIOR TO CONNECTION OF TELECOMMUNICATION WIRING. IN OUT MON NETWORK 4 3 2 ALL EMPTY SLOTS MUST BE COVERED WITH BLANK PANELS CONTROL /CHAIN 10 BASE T IN OUT MODULE 1 MODULE 4 MODULE 2 MODULE 5 P W R P W R MODULE 3 MODULE 6 A B I SEE MANUAL BEFORE REMOVING POWER SUPPLY (600e ONLY) O PORT X.1 NX 56/64 PORT X.
Chapter 2. Installation 3 2 1 CAUTION-RISK OF ELECTRIC SHOCK CAUTION: MAINTENANCE TO BE PERFORMED BY TRAINED SERVICE PERSONEL ONLY SUPPLEMENTAL EARTH GROUND MUST BE CONNECTED PRIOR TO CONNECTION OF TELECOMMUNICATION WIRING. IN OUT MON NETWORK ALL EMPTY SLOTS MUST BE COVERED WITH BLANK PANELS 4 CONTROL /CHAIN IN 10 BASE T OUT 5 MODULE 1 MODULE 4 MODULE 2 MODULE 5 P W R P W R MODULE 3 MODULE 6 A B SEE MANUAL BEFORE REMOVING POWER SUPPLY O PORT X.1 NX 56/64 PORT X.1 NX 56/64 PORT X.
Chapter 2. Installation 1 CAUTION-RISK OF ELECTRIC SHOCK CAUTION: MAINTENANCE TO BE PERFORMED BY TRAINED SERVICE PERSONEL ONLY SUPPLEMENTAL EARTH GROUND MUST BE CONNECTED PRIOR TO CONNECTION OF TELECOMMUNICATION WIRING. IN OUT MON NETWORK 5 3 2 ALL EMPTY SLOTS MUST BE COVERED WITH BLANK PANELS 4 CONTROL /CHAIN IN 10 BASE T OUT 6 MODULE 1 MODULE 4 MODULE 2 MODULE 5 MODULE 3 MODULE 6 P W R P W R A B I SEE MANUAL BEFORE REMOVING POWER SUPPLY (600e ONLY) O PORT X.1 NX 56/64 PORT X.
Chapter 2. Installation TSU 600 Interfaces The TSU 600 is equipped with six option slots, management interfaces, and a T1 interface, in the rear panel. See Figure 2-2. LAN PC or Modem Control 10BaseT Chain Input (600e only) Output NI TSU 600 Chain Input Chain Output NI TSU 600 Option Network Figure 2-2. TSU 600 Interfaces Network Interface The network interface (NI) port provides the connection to the T1. This port complies with the applicable ANSI and AT&T standards.
Chapter 2. Installation 10BaseT Interface (600e only) The 10BaseT interface provides the LAN interface for managing the TSU 600e with SNMP or T-watch PRO. For more information, see Wiring on page C-1. Option Slot Arrangement As viewed from the rear of the TSU 600, the slots are numbered as shown in Figure 2-3. All slots are functionally identical except slots one, two, and six. These slots offer additional functions.
Chapter 2. Installation Slots 3-5 Slots 3-5 will accept any interface type except secondary interface, the interface for DTE timing, or the multiport DBU. If other interfaces have any restriction on their location, this will be specified in the individual option card manual (provided with the option cards). Slot 6 Slot 6 services any option module type including secondary network interface ports (DSX-1 (PBX) and Full D&I), but not the DTE timing source.
Chapter 2. Installation The full self-test procedure (invoked from the front panel or T-Watch PRO) consists of the following tests: Board level tests Each of the TSU 600 boards contains an on-board processor which executes a series of tests checking the circuitry on the board.
Chapter 2. Installation Set Control Port The TSU 600 can be configured from the control port when T-Watch PRO, SNMP, or the terminal interface is being used. If the control port is to be used, the control port baud rate must also be selected. Chain-In (PC) The unit can be controlled from an external PC connected directly or via modem to the Chain-In port.
Chapter 2. Installation The Passcode, the Unit ID, and the Control Port settings are stored in a nonvolatile memory. This ensures that they are operable for subsequent power-up sequences. Normal Power-Up Procedure After the unit has been put into operation with the initial power-up and initialization, subsequent power-up procedure includes only the PowerUp Self-Test followed by the request for a passcode (password) if this option was selected during initialization.
Operation Chapter 3 FRONT PANEL The TSU 600 front panel both monitors operation and controls the configuration of the unit. The TSU 600 front panel is shown in Figure 3-1 on page 3-4. Descriptions of each part of the front panel follow. Name Description LCD Window Displays menu items and messages in two lines by 16 characters. It also displays alarm and status information. Enter Selects active menu items. To select a menu item, press the number of the item.
Chapter 3. Operation Name Description To enter special function keys, press and release Shift before pressing the key representing the desired character. See Operation Keys on page 3-5 for a description of the function keys. Shift To activate a special function key rather than a number, press Shift and then the key. If you press the key without using Shift, the numbered item becomes active instead of the special function key.
Chapter 3. Operation Module Status LEDs The module status LEDs display the operational condition of ports installed in the option slots. Name Description OK (green) Indicates the operation is in the normal mode and no errors have been detected. Test (yellow) Indicates that one of the interfaces is operating in a test mode. This includes a self-test or a test loopback. When lighted, this LED also indicates that normal data flow is not occurring in at least one of the module ports.
Chapter 3. Operation . 4 2 1 5 3 6 8 7 9 10 11 TSU 600 ENTER 1 2 3 4 5 ALARM 8 HOME 0 6 CLEAR 9 SHIFT # 7 COPY CANCEL SYSTEM 12 CSU * OK TEST ERROR 13 TEST ALARM ALARM 15 14 OK 16 1 2 3 4 5 6 17 1. LCD Window Displays menu items and messages in 2 lines by 16 characters. 2. Cancel Stops current activity and returns to the previous menu. 3. Enter Selects active menu item 4. Copy Copies last data entered into the current DS0. 5. Home Returns to the main menu. 6.
Chapter 3. Operation Operation Keys Name Description Copy Used in the DS0 mapping menu operations to copy the last data entered into the current DS0. This key operates without pressing the Shift key. Home Returns home to the Main Menu from any menu location. Alarm Used as quick access to the active alarm display menus. This can be activated while any other menu item is in use. When the Alarm Menu is exited, the unit returns to the location of the same menu that was active when Alarm was selected.
Chapter 3. Operation Selecting and Activating a Menu Item Step Action 1 Choose a menu item by placing the cursor on the desired menu item by either: 1. pressing the number corresponding to the menu item or, 2. highlighting it with the up and down arrows. 2 To activate the Alarm List option from the Status Menu do the following: 1. Activate the Status Menu using the arrow keys or by pressing 1. The cursor will flash on the number next to the activated selection. 2. Press Enter. 3.
Chapter 3. Operation Editing the Data Field Use the following steps to edit data fields preceded by a colon (:). Step Action Result 1 Position the cursor on the The cursor moves to the data field submenu item number (to the right of the submenu item and press Enter. name). 2 Using the arrows, scroll to The value settings display one-at-ascan the available value time in the data field position. settings.
Chapter 3. Operation Display Only Data Fields Data fields preceded by an equal (=) symbol cannot be edited. See Figure 3-3 and the instructions listed below. Data Field Display Field Figure 3-3. Display and Data Fields Step Action 1 Press Enter to move the cursor to the data field. 2 Use arrows to select AUTO and press Enter. • The unit automatically sets the Line Build Out. • The display field shows the value actually set.
Chapter 3. Operation Data Port Identification When configuring the unit, menu selections will include options from data port submenus. Selecting of data ports is necessary because the TSU 600 uses a Slot-Port method to identify which data port the menu item is referencing. If a module containing a PBX DSX-1 option card with an Nx56/64 plug-on interface is installed in option slot 6, it would be designated as: DSX-1 Passthru=6.1 Where slot=6 and port =1.
Chapter 3. Operation Front Panel Menu Structure The TSU 600 uses a multilevel menu structure containing both menu items and data fields. All menu operations and data display in the LCD window. The opening menu is the access point to all other operations. Each Main Menu item has several functions and submenus to identify and access specific parameters.
Chapter 3. Operation Alternate Methods of Control T-Watch PRO (ADTRAN PC Program) T-Watch PRO is the ADTRAN PC control program. It provides complete control over the configuration of the TSU 600 using a graphical interface and displays the same status and performance data as the front panel LCD. This data is displayed in the form of tables and graphs.
Chapter 3. Operation T-Watch PRO/EIA-232 Connection To set up the TSU 600 to work with T-Watch PRO over a direct EIA-232 connection, the following steps are required: Step Action 1 Set the Unit ID and the Passcode using the Front Panel. See Unit ID on page 6-3 and Change/Set a Passcode on page 6-3 for more details. 2 Set the Control Port rate to the same setting as the PC Com port.
Chapter 3. Operation Terminal Mode Connection The TSU 600 provides the front panel menus to a VT-100 type terminal. This mode can be used to configure and monitor the unit. Initiate this mode by typing PTT on the terminal once it is connected to the Chain-In port. For detailed information on this method of control, see Telnet Terminal Menus on page 8-1. Telnet Connection You can connect to the TSU 600 via telnet.
Chapter 3.
Status Menu Chapter 4 The Status menu branch allows you to view the status of the TSU 600 operation. See Figure 4-1. %AS %EF 1) NI PERF RPTS ES 2) NI ERRORS UAS SES 1)STATUS 3) ACTIVE ALARMS (ALARM LIST) END OF LIST 4)VIEW HISTORY (HISTORY LIST) END OF HISTORY 5) PORT STATUS OPTION LIST 6) REMOTE PORT 7) CLEAR PORT ALM 8) ENET STATUS 9) PS STATUS Figure 4-1.
Chapter 4. Status Menu Menu flow is normally depicted from left to right. Arrows on the lower right of the screen indicate the direction of scrolling to use to view additional menu items. At every level of the menu, pressing Cancel returns the system to the previous menu level. Press Cancel repeatedly to return the system to the main menu. Network Performance Reports (NI PERF RPTS) The Network Interface Performance Reports display the user copy of the performance data. See Figure 4-2.
Chapter 4. Status Menu If insufficient time has passed to collect data, NA displays. Continue with standard operating procedures to exit the display. When this menu is active, performance data can be cleared by pressing Clear (Shift 9) on the keypad. Only the user copy of the performance data is cleared. Since only the user’s copy of performance data is cleared by the TSU 600, the data displayed here might be different from the data sent to the network as PRM data.
Chapter 4. Status Menu Active Alarms This menu item displays a list of current alarms reported by either the base controller or any of the ports. If no alarms are current, the menu item displays End of List. See Figure 4-3. This display includes two lines of text. The top line is the alarm source. The bottom line is the alarm message. A list of alarm messages is found in Appendix C, System Messages, on page C-1.
Chapter 4. Status Menu Port Status Port Status displays the signals monitored on the data ports. For example, an Nx56/64 interface monitors the RTS, CTS, TD, and RD, along with other signal lines. When a port is selected, the LCD indicates whether the signal is present. Remote Port Remote Port displays the status of activity on the Chain-In remote port. This is useful for troubleshooting communication sessions, as well as verifying cabling. RX Characters received at remote port.
Chapter 4. Status Menu ENET Status (600e only) TX Indicates that data is being transmitted from the 10BaseT port RX Indicates that data is being received by the 10BaseT port LNK Indicates the current status of the 10BaseT link integrity test. This should always be on when the unit is connected to a functional 10BaseT hub. CPU Active when the CPE is accessing the 10BaseT interface. PS Status (600e only) Displays the status of Power Supply A (PSA) and Power Supply B (PSB) for AC powered units.
Configuration Menu Chapter 5 The Configuration menu sets the TSU 600 operational configuration, including all network interface parameters, the allocation of the DS0s, and the port parameters. See Figure 5-1.
Chapter 5. Configuration Menu Menu flow is normally depicted from left to right. Arrows on the lower right of the screen indicate the direction of scrolling to view additional menu items. At every level of the menu, pressing Cancel returns the system to the previous menu level. Pressing Cancel repeatedly returns the system to the Main menu. NETWORK (NI) This menu item accesses the configuration of parameters associated with the network interface in the base unit.
Chapter 5. Configuration Menu SET LBO Selects the line build out for the network interface. In AUTO mode, the TSU 600 sets the LBO based on the strength of the receive signal and displays the selected value. Choices: 0.0 dB, 7.5 dB, 15 dB, 22 dB, and Auto To activate the -36 dB receiver sensitivity, set the LBO to AUTO. This feature is useful in a point-to-point application where no network elements are involved.
Chapter 5. Configuration Menu TSU 600 Clock Sources The TSU 600 is operable from various clock sources, permitting it to perform properly in many different applications. The network interface timing mode is set by using the Network (NI) Configuration menu options. The following options are available: • • • • • • Network Timing DTE Timing UBR1TE Internal Timing Secondary Timing Normal (CSU) Timing The selected clock option always designates the clock source for transmission.
Chapter 5. Configuration Menu DTE Timing The DTE is the source of timing. The TSU 600 uses the incoming DTE clock to determine the transmission timing. This is typically used in applications where it is necessary to have the DTE as the primary clock source (such as limited distance line drivers). See Figure 5-3. The DTE source timing is restricted from use when a secondary interface is used at the same time. Clock NETWORK INTERFACE 1 2 3 4 5 6 OPTION SLOTS DTE TIMING SOURCE Figure 5-3.
Chapter 5. Configuration Menu Internal Timing The TSU 600 is the source of timing. The TSU 600 is configured to use its own internal oscillator as the source of timing. Applications include private line driver circuits where one end is set to network and the other to internal. See Figure 5-4. NETWORK INTERFACE 1 2 3 4 5 6 SECONDARY INTERFACE (Option) OPTION SLOTS OSC TIMING SOURCE Figure 5-4.
Chapter 5. Configuration Menu Secondary Timing The secondary interface is the source of timing. The TSU 600 uses the clock derived by the secondary interface for transmission timing. See Figure 5-5. NETWORK INTERFACE 1 2 3 4 5 6 SECONDARY INTERFACE (Option) OSC OPTION SLOTS TIMING SOURCE PBX or Second Network Figure 5-5.
Chapter 5. Configuration Menu Normal (CSU) Timing The typical timing option arrangement is shown in Figure 5-6. The PBX is looped timed to the TSU 600. The Network Interface (NI) is the actual source of timing. This timing option is the same as that typically used for CSUs. This is the preferred mode for use with a PBX application. NETWORK INTERFACE 1 2 3 4 5 6 SECONDARY INTERFACE (Option) TIMING SOURCE OSC OPTION SLOTS PBX or Second Network Figure 5-6.
Chapter 5. Configuration Menu Unit Menu The Unit menu changes the baud rate of the Chain-In port and the setup of the Chain-Out port. The menu items are: Ctl Port Rate Sets the baud rate for communication with the PC or modem. Choices: 1200, 2400, 9600, 19200 and 38400 kbps Traps Enables or disables the transmission of trap messages. Choices: Enable, Disable Access Sets the method of connection from the TSU 600 to T-Watch PRO/SNMP.
Chapter 5. Configuration Menu Subnet Mask Defines which part of a destination IP address is the network number. Used along with the TSU 600e IP address to determine which nodes must be reached through the default IP Gateway. This value is set to 0.0.0.0 when the IP interface option is set to SLIP. Default Router All IP Packets destined for nodes not on the TSU 600e unit’s local network are not forwarded through this IP address.
Chapter 5. Configuration Menu Map Exchange (Map Xchng) Menu The Map Exchange menu enables and sets the automatic time-of- day map switch. The unit provides selection of the hour, minute, and seconds for the map switching to take place. The menu items are: OFF Indicates the map in use does not change (disabled). Off disables the Automatic Map Change feature. Press Enter to activate the selection. AUTO Indicates that the map in use will change at a userselected time of day.
Chapter 5. Configuration Menu DS0 Map A and DS0 Map B Menu The DS0 maps designate which DS0s are assigned to which port. See Figure 5-7. There are three maps: DS0 Map A, DS0 Map B, and the Temporary (Temp) map. TEMP DS0 A DS0 B Figure 5-7. DS0 Map Designations DS0 A and DS0 B are the current maps the TSU 600 uses. The Temp Map generates a map before putting it into use. You can copy DS0 A to DS0 B by copying the DS0 A map into the Temp map. Then apply (write) the Temp map into DS0 B.
Chapter 5. Configuration Menu REVIEW MAP A(B) Permits a quick review of the number of DS0s assigned to each port and the number of unassigned DS0s (Idle or TST) as defined in the currently applied Map A(B). REVIEW TEMP This menu item is operated the same for the Temp map as is 3)REVIEW MAP A or Map B. EDIT TEMP The map in the Temp file can be edited to whatever configuration is desired.
Chapter 5. Configuration Menu 1. With the cursor on CREATE TEMP , press Enter. The unit displays the selection screen with the cursor positioned on the first selection DS0 number. See Figure 5-8. Select DSO Number Select Port Figure 5-8. Create Temp Selection Screen 2. Enter the DS0 number by using either the scroll method or numbers. Do not mix the use of the keys. 3. Pressing Enter completes the selection and moves the cursor to PORT, the next field. 4.
Chapter 5. Configuration Menu Port Configuration (Port Config) Port Configuration selects and configures the parameters associated with any data port in the unit. For example, parameters for the DSX-1 (PBX) interface are set through this menu. The items that can be set depend on which option module is installed. The list of option ports will vary with the configuration.
Chapter 5.
Utility Menu Chapter 6 The utility menu tree displays and sets system parameters. See Figure 61. This includes setting the time and date, resetting all parameters to factory values, or re-initiating the unit. This menu also displays the unit software revision and the Unit ID setting.
Chapter 6. Utility Menu Menu flow is normally depicted from left to right. Arrows on the lower right of the screen indicate the scrolling direction to view additional menu items. At every level of the menu, press Cancel to return the system to the previous menu level. Pressing Cancel repeatedly returns the system to the Main menu. Time/Date This menu option displays or edits the current time and date. The TSU 600 maintains the time and date during power-off conditions. If you want to... Do this...
Chapter 6. Utility Menu Pressing any key after entering a passcode causes the unit to return to the previous active menu. In this case it returns to 2)CONFIG, 2)UNIT, 1)CTL PORT RATE to permit changing the data rate. Change/Set a Passcode The passcode can be changed or set at any time or eliminated altogether through the Utility menu item 3)SET PASSCODE. This procedure requires the current passcode (if one is established) for operation. The passcode can only be entered by using numbers.
Chapter 6. Utility Menu Setting the Unit Identification In the Unit ID menu (item 4) under the UTIL menu, enter any value between 2 and 999. The number 1 is reserved for the PC. Pressing Enter records the Unit ID number and establishes its availability for operation by remote control. The unit proceeds to the Set Control Port prompt. No Unit ID Desired Without entering any numbers at the Unit ID prompt, press Enter.
Test Menu Chapter 7 The Test menu initiates different types of unit tests and displays test results in the LCD window. The Test menu contains four items. See Figure 7-1. Executing tests will disrupt some of the normal operation. See individual menu items concerning tests before executing.
Chapter 7. Test Menu Menu flow is normally depicted from left to right. Arrows on the lower right of the screen indicate the scrolling direction to view additional menu items. At every level of the menu, pressing Cancel returns the system to the previous menu level. Pressing Cancel repeatedly returns the system to the Main menu. Network Tests Network tests control the activation of loopbacks and the initiation of data test patterns. Network tests are run on the Network Interface (NI).
Chapter 7. Test Menu Network Interface Loopbacks Network interface loopbacks affect the entire T1 data stream. There are two types of network loopbacks: line loopback and payload loopback. Line loopback loops all of the received data back toward the network. The transmitted data is the identical line code that was received, including any bipolar violations or framing errors.
Chapter 7. Test Menu Remote Loopbk This activates the same loopbacks as Local Loopback but at the far end. It uses either the inband loopup code as specified by ANSI T1.403 for line loopback (ATT In-Band LLB), or the FDL as specified in ANSI T1.403 for payload and line loopback codes.
Chapter 7. Test Menu Test Pattern Pattern Description All Ones Sends an all ones pattern to the network All Zeros Sends an all zeros pattern to the network QRSS All DS0s Generates a QRSS test pattern and inserts the pattern into all DS0s QRSS TST DS0s Inserts a QRSS pattern in those DS0s mapped as TST in the currently active map (A or B) None Terminates pattern generation QRSS Pattern The QRSS pattern is commonly used to simulate real data in T1 interfaces.
Chapter 7. Test Menu Pattern Result Displays the results of the test currently active. Leaving and returning to this menu item does not interrupt the test. Pressing 2 injects errors into the test pattern. These errors are detected by the device performing the pattern check.
Chapter 7. Test Menu Run Self-Test The self-test checks the integrity of the internal operation of the electronic components by performing memory tests and by sending and verifying data test patterns through all internal interfaces. Although actual user data cannot be passed during these tests, the self-test can be run with the network and DTE interfaces in place and will not disturb any external interface. The memory portion of the self-test automatically executes upon powerup.
Chapter 7. Test Menu Port Tests The Port Tests menu is used to activate testing of specific data ports. It controls the activation of loopbacks and the initiation of data test patterns. Test results are displayed in the LCD window. The execution of Port Tests will disrupt normal data flow in the port being tested. Cancel Tests Use this menu selection to deactivate all active tests, including tests on option modules.
Telnet/Terminal Menus Chapter 8 MAIN MENU The Telnet/Terminal Main Menu is the first menu displayed after the telnet/terminal session is established. See Figure 8-1. The default telnet/ terminal password is ADTRAN. Only one telnet/terminal session may be active at a time. ADTRAN - TSU 600 Password: XXXXXXXX Main Menu 1) 2) 3) 4) 5) 6) 7) 8) Status Config Util Test Remote Menu Access Management Config Flash Download Quit Session Figure 8-1.
Chapter 8. Telnet/Terminal Menus Status, Config, Util, and Test Menu Options These menu items can access the same modified menus that you can access through the front panel. For detailed information on the available menu options, refer to the following sections: • • • • Status Menu in Chapter 4. Configuration Menu in Chapter 5. Utility Menu in Chapter 6. Test Menu in Chapter 7.
Chapter 8. Telnet/Terminal Menus Normally, map configuration involves these steps. Step Action 1 Initializes the Temp Map to one of three configurations (current Map A, current Map B, or all IDLEs). This step is optional. 2 Edits the Temp Map so that it reflects the desired map configuration. 3 Replaces the current DS0 map A or B configuration with the Temp Map configuration. Initializing the Temp Map Upon entering the DS0 maps configuration menu, the Temp Map reflects its last configured state.
Chapter 8. Telnet/Terminal Menus Editing the Temp Map If further changes to the Temp Map are needed, do the following: Step 1 Action Explanation Use selection 7 to enter the Temp Map edit mode. Upon entering this mode, the cursor location moves to DS0 number one in the DS0 field of the Temp Map. The cursor may be moved from one DS0 to another by using the up and down arrows until the cursor is located at the DS0 number whose assigned port needs to be changed.
Chapter 8. Telnet/Terminal Menus Remote Menu Access Displays telnet menus for a remote device (may be another TSU/TDU or any other ADTRAN product that supports telnet via its EIA-232 chain port). After selecting this option, you may choose to connect to a device entered in the Unit Access Table or enter a Unit ID for a unit not in the Unit Access Table. CTRL + X terminates the session and returns to the TSU 600 Main Menu.
Chapter 8. Telnet/Terminal Menus __________________Unit Access Table_________________ Unit ID Passcode Type Polled 20 DEFAULT Standard No 3 0033 Standard Yes 6 0095 TSU Stand Alone No 8 0022 Standard Yes PollStatus UP UP 1) Add New Unit 2) Modify Unit 3) Delete Unit 4) Default Unit Passcode 0022 5) OK Figure 8-3. Unit Access Table Add New Unit This adds a new device to the table. You must enter a device Unit ID, passcode, unit type, and polled flag.
Chapter 8. Telnet/Terminal Menus Default Unit Passcode Sets the default passcode for all devices in the table that have passcodes set to DEFAULT, or for any unit not listed in the table. OK Returns to the Configure Agent menu. SNMP Read Community SNMP Read Community Name defaults to public. NMSs using this community name have Read access for all supported MIB objects but do not have the ability to change MIB objects. This value must be set to the same value on both the TSU 600 and the NMS (OpenView®, etc.
Chapter 8. Telnet/Terminal Menus SNMP Trap Community This community name is used for all SNMP traps forwarded by the TSU 600. Traps received from daisy chained units have a period and the Unit ID appended to the trap community name. SNMP Trap Destination Address Host 1 Trap IP Address Description This is the first of four entries for SNMP trap destination addresses. The TSU 600 forwards all SNMP traps to the IP address specified in this entry. If the address is set to the default value of 0.0.0.
Chapter 8. Telnet/Terminal Menus Auto. Fail Traps Sent (DISABLED, ENABLED: defaults to DISABLED) When enabled, the TSU 600 issues an SNMP trap when any SNMP request is received with an invalid community name. Can be used for security purposes. Poll Link Status Traps Sent (DISABLED, ENABLED, defaults to DISABLED) When enabled, the TSU 600 sends an SNMP trap whenever a device configured to be polled fails to respond. When the device begins responding to polls, a poll link-up trap is sent.
Chapter 8.
Appendix A Understanding SNMP As local area network (LAN) environments became standardized over the past ten years, multi-vendor equipment grew with competition. It became necessary to manage the various vendor equipment from a single control console. Thus, the SNMP emerged as the standard for managing commercial TCP/IP networks.
Appendix A. Understanding SNMP MIB This is an index to the organized data within a network device. It defines the operating parameters that can be controlled or monitored. When requesting the network manager to retrieve or modify a particular piece of information about a network device, the network manager transmits the request to that network device. The agent in that device interprets the incoming request, performs the requested task, and sends its response to the network manager.
Appendix A. Understanding SNMP TSU 600 SNMP ACCESS By default, SNMP MIB Browser access to the TSU 600 IP address with the configured community names, accesses the host. The TSU 600 can also act as an SNMP proxy agent for external units. To access MIB variables on externally chained devices, append a period and the Unit ID of the device to the Read and Read/Write community names. Example: If the Read community name configured in the TSU 600 is public, specifying "public.
Appendix A. Understanding SNMP For traps from the ISU 512, the Unit ID is the first object identifier. See the product MIBs for more information. Definitions for Poll Link Up/Down traps are included in the TSU 600 MIB file: 600e.MIB. The TSU 600 and TSU 600e share the same MIB. SNMP MIB Browser Configuration The steps required to configure Network Manager MIB variable access through the TSU 600 are as follows: 1. Load the desired product MIBs on the network management station.
Appendix B Understanding TR-08 The TSU 600 chassis functions as a Remote Terminal in Digital Loop Carrier and as Integrated Digital Loop Carrier Systems as described in TR-TSY 000008. The TSU 600 supports SLC96 framing, Mode I operation, ORB-13 and ORB-16 alarm formats, alarm reporting, and user-definable BPV threshold detection rate.
Appendix B. Understanding TR-08 The following table explains what conditions trigger alarms and how alarms are processed when received by the TSU 600. Table B-1. Alarm Conditions Name Explanation FELP When the TSU 600 receives a FELP alarm, it will loop the incoming data directly to the outgoing data. LINE ON is placed in history. The alarms and loopback are cleared when FELP is no longer received. Loss of Data The TSU 600 will send MINOR ALARM and the A SHELF ALARM for 2.
Appendix B. Understanding TR-08 TR-08 DS0 Conversion Table The following table contains the mapping conversions needed to map voice ports to the TR-08 network. Table B-2. TR-08 DS0 Conversion Table 61202076L1-1 DS0 TR-08 Channel Number Port 1 1 1.1 3 2 1.2 5 3 1.3 7 4 1.4 9 5 2.1 11 6 2.2 13 7 2.3 15 8 2.4 17 9 3.1 19 10 3.2 21 11 3.3 23 12 3.4 2 13 4.1 4 14 4.2 6 15 4.3 8 16 4.4 10 17 5.1 12 18 5.2 14 19 5.3 16 20 5.4 18 21 6.1 20 22 6.
Appendix B.
Network Pinouts Appendix C WIRING Network On the rear panel of the TSU 600 is an 8-position modular jack labeled NETWORK. This connector is used for connecting to the network. See Table C-1, Network Pinouts for the pinout for the network connector. Network Connections The network connections are as follows: Connector Type (USOC) RJ-48C Part Number AMP# 555164-2 Table C-1.
Appendix C. Network Pinouts Control In/Chain In This is used as an EIA-232 port for connection to a computer or modem (Control-in) or to another TSU 600 or TSU 100 (chain-in). See Table C-2, Control In/Chain In Pinout for the pinout for the control-in/chain-in connector. Chain-in Connections The chain-in connections are as follows: Connector Type RJ-48 Part Number AMP# 555164-2 Table C-2.
Appendix C. Network Pinouts Chain-Out This is used to connect to another TSU 600 chain-in connector. See Table C-3, Chain-Out Pinout for the pinout for the chain-out connector. Chain-out Connections The chain-out connections are: Connector Type RJ-48 Part Number AMP# 555164-2 Table C-3. Chain-Out Pinout Pin Name 1 GND 2 UNUSED 3 TX DATA 4 UNUSED 5 RX DATA Description Ground-connected to unit chassis. Connected to GND of next unit (pin 10). Data transmitted to chained units by the TSU 600.
Appendix C. Network Pinouts 10BaseT (600e only) 10BaseT is used to connect the TSU 600e to the Local Area Network. See Table C-4. 10BaseT Connections The required wiring connections are: Connector Type (USOC) RJ-45 Part Number AMP# 555164-1 Table C-4.
Appendix D System Messages This appendix lists and defines the alarm and status messages that appear on the TSU 600 screen.
Appendix D. System Messages Status Messages: Network Interface (NI) Message Description Payload On Payload loopback activated Line On Loopback off Loopback Off All loopbacks deactivated Factory Restore Factory setting restored Power On Unit powered on Self-Test Internal self-test performed TR-08 DL Down* TR-08 data link is down TR-08 DL Up* TR-08 data link is up Minor Alarm* Loss of sync, carrier loss, BPV threshold exceeded, or data link failure.
Specifications Appendix E ELECTRICAL SPECIFICATIONS T1/FT1 Interface 61202076L1-1 T1 Line Rate 1.544 Mbits/s ± 75bps Line Code Bipolar, RZ; AMI or B8ZS Framing D4(SF), ESF, or SLC96 FT1 Line Rate DS0 Channelized (multiple of 64 kbps) Transmit Timing Network, DTE, U-BR1TE Secondary NI, Normal (CSU) or Internal Input Signal 0 to -36 dB (DS-1) Line Build-out 0, 7.5, 15, 22.
Appendix E. Specifications Compatibility T1 Interface Pub 62411 ESF Format Interface TR. 194 ESF Performance Monitoring TR. 54016 and T1.
Appendix E. Specifications Environmental Specifications Input Power TSU 600: 90 - 130 VAC 60 HZ TSU 600e: 90 - 120 VAC 50/60 HZ DC powered units: 21 - 26 VDC or 40 - 56 VDC Fuse AC powered units: 1A, 250V DC powered units: 5A, 250V Operating Temperature 0 to 45 degrees C Max Power 40 W Consumption Max Current 61202076L1-1 AC powered units: 0.
Appendix E.
Index Numerics ANSI FDL PLB, remote loopback 7- 10BaseT Connections C-4 10BaseT Interface 2-10 10BaseT, interface with SNMP 3-12 ANSI FT1 LLB, remote loopback 4 A Access, unit menu 5-9 Active Alarms 4-4 Add New Unit to unit access table, how to 8-6 ADTRAN PC Management Program, T-Watch PRO 3-11 ADTRAN PC Program, T-Watch PRO 3-11 ADTRAN Web page 3-12 Agent, SNMP component A-1 AIS Alarm, (Blue Alarm) network interface alarm message D-1 Alarm (red), LED description 3-2 Alarm (red), module status LED 3-
Index Chain Port Output 2-9 Chain-In (PC) 2-13 Chain-in Connections C-2 Chain-out Connections C-3 Chain-Out Pinout C-3 Chassis Specification E-2 Clear alarm history 4-4 Clear Port Alarm 4-5 Clear,operation key 3-5 CMD Mode, utility menu 6-4 Config, front panel menu 3-10 configuration applications, TSU 600 1-5 Configuration Menu Tree 5-1 Control Port Input 2-9 Control Port, unit menu 5-9 COPY A >TEMP, DS0 map menu item 5-12 Copy, operation key 3-5 CRC, TSU 600 T1 error 4-3 CREATE TEMP, DS0 map menu item
Index GetResponse, SNMP message Grounding Instructions 2-4 A-2 H 3-11 Home, operation key 3-5 http //www.adtran.
Index No Loopback, setting local loopback 7-3 No Unit ID Desired, utility menu, what to do 6-4 Normal (CSU) Timing 5-8 Normal Power-Up Procedure 2-14 Numeric Keypad, front panel 3-1 Nx56 1-3 Nx56/64 module, router interface 1-6 Nx56/64 Serial Interface, option module for TSU 600 1-3 NxIQ, option module for TSU 600 1-3 O message D-2 power-up procedure 2-14 Power-up Testing 2-11 Product Description, TSU 600 1-1 Product Overview, TSU 600 1-1 Protection Line Switch, alarm condition TR-08 B-2 Proxy Traps, un
Index errors 7-6 SES, severly errored seconds, NI errors 4-2 Set Control Port 2-13 SET LBO, network menu itme 5-3 Set Passcode, how to 6-2 Set Unit Identification 2-12 Set User Passcode 2-12 SetRequest, SNMP command A-2 Setting the Unit Identification for utility menu, how to 6-4 Shift, front panel 3-2 shipping damages, what to do 2-1 Simple Network Management Protocol (SNMP) 3-12 SLIP Flow CTL, unit menu 5-10 SLIP Rate, unit menu 5-10 SNMP Commands A-2 SNMP Messages A-2 SNMP MIB Browser Configuration A-4
Index 3-12 T-Watch PRO/LAN Connection 3-11 V Voice Interface, option module for TSU 600 1-3 U UAS, unavailable errored sec.
Product Support Information Presales Inquiries and Applications Support Please contact your local distributor, ADTRAN Applications Engineering, or ADTRAN Sales: Applications Engineering (800) 615-1176 Sales (800) 827-0807 Post-Sale Support Please contact your local distributor first. If your local distributor cannot help, please contact ADTRAN Technical Support and have the unit serial number available.
