Datasheet

jobAid
DESCRIPTION
TheOC‐12SmallForm‐FactorPluggableCWDM1491nm(SFP
OC‐12)plugsintoADTRANOC‐12equipmentdesignedtoaccept
SmallForm‐factorPluggables(SFPs).
Installedintoanappropriatehostunit,theSFPOC‐12providesan
OC‐12CWDMinterfacetothesupportingsystem.
NOTE
Toensurecompatibility,refertothedocumentationprovided
withthehostmodule.
ThefollowingfeaturesaresupportedontheSFPOC‐12:
♦ SONETOC‐12compatible(622.08Mb/s)1491nm,
longreach,single‐mode,2‐fiberoperation
♦ 80kmmaximumopticalspan
CAUTION
!
Duetocompliancecertificationrequirements,useonly SFPs
suppliedbyADTRANwiththehostmodule.ADTRANcannot
certifysystemintegritywithotherSFPs.
SPECIFICATIONS
♦ OpticalSpecifications:
◊ Opticaltransmitlevel:–3dBmto+5dBm
◊ Opticalreceivelevel:–28dBmto–8dBm
◊ Powerpenalty:–1dB
◊ Opticalbudget:24(±1)dBm
◊ Minimumspanattenuation:13dB
◊ Opticalconnectors:LC
♦ ExtendedEnvironmentalSupport:
◊ Operationaltemperaturerange:–40°Cto+65°C
◊ Storagetemperaturerange:–40°Cto+85°C
◊ Relativehumidityto95%,noncondensing
OC-12 Small Form-Factor Pluggable
CWDM 1491 nm
INSTALLATION
ToinstalltheSFPOC‐12intoanappropriatemodule,complete
thefollowingsteps:
1. InspecttheSFPOC‐12.Ifdamaged,fileaclaimwiththecar‐
rierandthencontactADTRANCustomerSupport.
CAUTION
!
DonotremovetheprotectiveendcapfromtheSFPuntilthefiber
opticcableisreadytobeconnected.
2. InserttheSFPOC‐12intotheSFPcageonthemodule.
Ensurethatthemanufacturer’slabelontheSFPisfacing
upwardforcorrectinstallation.
3. SlidetheSFPOC‐12allthewayintothereceptacleuntil
thereisanaudible“click”.
NOTE
ThelatchontheSFPisusedtoremovetheSFPfromthecageon
thecircuitcard.
PROVISIONING
The SFPOC‐12 is not directly provisionable. To provision the
SFPOC‐12, access the menu system of the host module.
Refer to the “Provisioning” section of the Job Aid or I&M
provided with the host module for provisioning details.
SAFETY AND REGULATORY COMPLIANCE
CAUTION
!
ElectrostaticDisc harge (ESD)candamageelectronicmodules.
Whenhandlingmodules,wearanantistaticdischargewriststrap
topreventdamagetoelectroniccom pon ents .Placemodulesin
antistaticpackingmaterialwhentransportingorstoring.When
wor kin g on modules, always placethem on an approved
antistaticmatthatiselectricallygrounded.
TheSFPOC‐12isNRTLListedtotheapplicableULstandards.
TheSFPOC‐12meetsorexceedsalltheapplicablerequirements
ofNEBS,TelcordiaGR‐63‐CORE,GR‐1089‐CORE,andETSIEN
300368.
TheSFPOC‐12isintendedfordeploymentin
CentralOfficetype
facilities,EEEs,EECs,andlocationswheretheNECapplies(for
example,CustomerPremises).TheSFPOC‐12istobeinstalledin
ADTRANproductsinRestrictedAccessLocationsonly,and
installedbytrainedservicepersonnel.
CLEI: SOOTAKNJ_ _
Product P/N: 1442703PG2
Issue Date: December 2010
Document P/N: 61442703PG2-22B