Datasheet

jobAid
DESCRIPTION
TheSmallForm‐FactorPluggableOC‐12Bidirectional1550/1310
nm(BidirectionalSFP)plugsintoADTRANequipmentdesigned
toacceptSmallForm‐factorPluggables(SFPs).Installedintoan
appropriatehostunit,theBidirectionalSFPprovidesanOC‐12
interfacetothesupportingsystem.
NOTE
Toensurecompatibility,refertothedocumentationprovi ded
withthehostmodule.
ThefollowingfeaturesaresupportedontheBidirectionalSFP:
♦ SONETOC‐12compatible(622Mb/s),single‐fiberoperation
♦ 15kmmaximumopticalspan
CAUTION
!
Duetocompliancecertificationrequirements,onlySFPssupplied
byADTRANaretobeusedwiththehostmodule.ADTRAN
cannotcertifysystemintegritywithotherSFPs.
SPECIFICATIONS
♦ OpticalSpecifications:
◊ Opticaltransmitlevel:–8dBmto–15dBm
◊ Opticalreceivelevel:–8dBmto–28dBm
◊ TransmitWavelength:1550nm
◊ ReceiveWavelength:1310nm
◊ Opticalbudget:12(±1)dBm
◊ Opticalconnectors:LC
Small Form-Factor Pluggable OC-12
Bidirectional 1550/1310 nm
♦ ExtendedEnvironmentalSupport:
◊ Operationaltemperaturerange:–40°Cto+65°C
◊ Storagetemperaturerange:–40°Cto+85°C
◊ Relativehumidityto95%,noncondensing
INSTALLATION
ToinstalltheBidirectionalSFPintoanappropriatemodule,
completethefollowingsteps:
1. InspecttheBidirectionalSFP.Ifdamaged,fileaclaimwith
thecarrierandthencontactADTRANCustomerSupport.
CAUTION
!
DonotremovetheprotectiveendcapfromtheSFPuntilthefiber
opticcableisreadytobeconnected.
2. InserttheBidirectionalSFPintotheSFPcageonthemodule.
Ensurethatthemanufacturer’slabelontheSFPisfacing
upwardforcorrectinstallation.
3. SlidetheBidirectionalSFPallthewayintothereceptacle
untilthereisanaudible“click”.
NOTE
ThelatchontheSFPisusedtoremovetheSFPfromthecageon
thecircuitcard.
SAFETY AND REGULATORY COMPLIANCE
CAUTION
!
♦ ElectrostaticDischarge(ESD)candamageelectronicmodules.
Whenhandlingmodules,wearanan ti st ati c dischargewrist
straptoprevent damageto el ectronic components.Place
modulesinantistaticpackingmaterialwhentra nsportingor
storing.Whenworkingonmodules,alwaysplacethemonan
approvedantistaticmatthatiselectricallygrounded.
♦ TheSFPmeetsorexceedsalltheapplicablerequirementsof
NEBS,TelcordiaGR‐63‐CORE,GR‐10 89 ‐CORE,andETSIEN
300368.TheBidirectionalSFPisintendedfordeploymentin
CentralOfficetypefacilities,EEEs,EECs,andlocationswhere
theNECapplies(forexample,CustomerPremises).TheSFPis
tobeinstalledin
ADTRANproductsinRestrictedAc cess
Locationsonly,andinstalledbytrainedservicepersonnel.
ThisdevicecomplieswithPart15oftheFCCrules.Operationis
subjecttothefollowingtwoconditions:
1. Thisdevicemaynotcauseharmfulinterference
2. Thisdevicemustacceptanyinterferencereceived,including
interferencethatmaycauseundesiredoperation.
Changesormodificationsnotexpresslyapproved
byADTRAN
couldvoidtheuserʹsauthoritytooperatethisequipment.
CLEI: S00TALBJ__
Product P/N: 1442704PG2
Issue Date: October 2010
Document P/N: 61442704PG2-22A