TOTAL ACCESS 850 System Manual 64203376L1-1B August 2004 1200375L1 Total Access 850 Chassis 1200373L1 T1 Bank Controller Unit (BCU) 1200373L2 T1 BCU with DSX Port 4203376L1#TDM T1 Router Control Unit (RCU) with TDM Software 4203376L1#ATM T1 RCU with ATM Software 1203376L1 3rd Generation T1 RCU 1200377L1 SDSL RCU 1200377L2 2nd Generation SDSL RCU 1203384L2 Echo Canceller with ADPCM 1175006L2 Power Supply Unit 1175043L3 AC Supply/Battery Charger
Trademarks Total Access 850 System Manual Trademarks Any brand names and product names included in this manual are trademarks, registered trademarks, or trade names of their respective holders. Total Access® is a registered trademark of ADTRAN, Inc. To the Holder of the Manual The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change the contents without prior notice.
Total Access 850 System Manual Revision History Revision History Document Revision Date Description of Changes A April 2004 This is the first issue of this manual. The previous version of this product was covered under document 64200376L1-1. B August 2004 Update licensing and warranty agreement; correct third generation part numbers. Conventions Notes provide additional useful information. Cautions signify information that could prevent service interruption.
Safety Instructions Total Access 850 System Manual Safety Instructions When using your telephone equipment, please follow these basic safety precautions to reduce the risk of fire, electrical shock, or personal injury: 1. Do not use this product near water, such as a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. 2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote risk of shock from lightning. 3.
Total Access 850 System Manual FCC-Required Information FCC-Required Information FCC regulations require that the following information be provided in this manual: 1. This equipment complies with Part 68 of the FCC rules and requirements adopted by ACTA. On the equipment housing is a label showing the FCC registration number and ringer equivalence number (REN). If requested, provide this information to the telephone company. 2.
FCC-Required Information Total Access 850 System Manual Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Total Access 850 System Manual Affidavit Requirements for Connection to Digital Services Affidavit Requirements for Connection to Digital Services • An affidavit is required to be given to the telephone company whenever digital terminal equipment without encoded analog content and billing protection is used to transmit digital signals containing encoded analog content which are intended for eventual conversion into voice band analog signal and transmitted on the network.
Affidavit Requirements for Connection to Digital Services Total Access 850 System Manual AFFIDAVIT FOR CONNECTION OF CUSTOMER PREMISES EQUIPMENT TO 1.
Total Access 850 System Manual Industry Canada Compliance Information Industry Canada Compliance Information The Industry Canada Certification label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department of Commerce does not guarantee the equipment will operate to the user's satisfaction.
Product Warranty Total Access 850 System Manual Product Warranty ADTRAN will repair and return this product within the warranty period if it does not meet its published specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty. Software Licensing Agreement Each ADTRAN product contains a single license for ADTRAN supplied software.
Total Access 850 System Manual Customer Service, Product Support Information, and Training When needed, further pre-sales assistance is available by calling our Applications Engineering Department. Applications Engineering (800) 615-1176 64203376L1-1B © 2004 ADTRAN, Inc.
Customer Service, Product Support Information, and Training Total Access 850 System Manual Post-Sale Support Your reseller should serve as the first point of contact for support. If additional support is needed, the ADTRAN Support web site provides a variety of support services such as a searchable knowledge base, updated firmware releases, latest product documentation, service request ticket generation and trouble-shooting tools. All of this, and more, is available at: http://support.adtran.
Total Access 850 System Manual Table of Contents Table of Contents Section 1 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 This section provides an overview of the Total Access 850 system. Section 2 Engineering Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 This section provides equipment dimensions, power requirements, front panel design, rear panel design, LEDs, and at-a-glance specifications.
Table of Contents 14 Total Access 850 System Manual © 2004 ADTRAN, Inc.
SYSTEM DESCRIPTION This section provides an overview of the Total Access 850 system. CONTENTS Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Configuration and Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Software Upgradeable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 1 System Description 16 Total Access 850 System Manual © 2004 ADTRAN, Inc.
Total Access 850 System Manual 1. Section 1 System Description SYSTEM OVERVIEW The Total Access 850 is an integrated access device designed for cost-effective deployment of voice and data services at the customer premises. The Total Access 850 system benefits integrated communications providers, such as CLECs, ILECs, and ISPs, who require a customer premises device that integrates voice and data functions.
Section 1 System Description Total Access 850 System Manual Integrated Components (with RCU) • • • IP router DSX-1 T1/PBX interface V.35 Nx56/64 DTE interface Testing • • Local and remote: payload/line, V.54 (depending on installed modules) Patterns: 511, QRSS, all ones, all zeros (depending on installed modules) Performance Monitoring • • • 3. Reports: Information stored for last 24 hours in 15 minute increments Performance statistics per TR54016, T1.403, RFC1406 Alarm reporting per TR54016, T1.
Total Access 850 System Manual Section 1 System Description Access Modules (Requiring a BCU) • • • • E&M/TO Access Module (P/N 1180402L1) OCU DP Access Module (P/N 1180005L1) Single DS0 DP Access Module (P/N 1180003L1) Nx56/64 (V.35) Access Module (P/N 1200372L1) Each access module is hot-swappable, with configuration restored upon replacement. Replacing an access module with a different module type will result in configuration loss.
Section 1 System Description Total Access 850 System Manual built-in Echo Cancellation for up to 24 voice ports. Adaptive Differential Pulse Code Modulation (ADPCM) resources are also built-in for up to 16 ports. Power Supply Unit (P/N 1175006L2) The Total Access 850 PSU is a common module plug-in unit designed to supply power to the system. The faceplate contains a momentary ACO pushbutton, a ring voltage Enable/Disable pushbutton, a Bank Alarm LED, Ring LED, and a power LED.
Total Access 850 System Manual Section 1 System Description OCU DP Access Module (P/N 1180005L1) This module is only available in Total Access 850 systems using a BCU. The OCU DP module is a single port access module used to provide the interface between a DS0 time slot on the T1 and a 4-wire DDS device at the customer premises. The OCU DP supports up to 18 kft of copper for remote DSU connectivity.
Section 1 System Description 22 Total Access 850 System Manual © 2004 ADTRAN, Inc.
ENGINEERING GUIDELINES This section provides equipment dimensions, power requirements, front panel design, rear panel design, LEDs, and at-a-glance specifications. CONTENTS Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 AC System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 DC System . . . . . . . . . . . . . . . . . . . . . .
Section 2 Engineering Guidelines Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Table 36. Table 37. Table 38. Table 39. 24 Total Access 850 System Manual T1 RCU Faceplate LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total Access 850 System Manual 1. Section 2 Engineering Guidelines EQUIPMENT DIMENSIONS The Total Access 850 chassis is 8.5” W, 11” D, and 3.5” H and can be mounted in a 19-inch or 23-inch rack (mounting brackets included in shipment). All other equipment (modules) fit inside the base unit. 2.
Section 2 Engineering Guidelines Total Access 850 System Manual Bank Controller Unit (1200373L1 and 1200373L2) The following is operational information pertaining to the Bank Controller Unit when used with the Total Access 850 system. Faceplate LEDs The faceplate Network LEDs labeled T1 NETWORK and T1 FRACTIONAL provide status information using a color coded message format. Table 1 gives a description of all faceplate LEDs for the BCU when used with the Total Access 850 system. Table 1.
Total Access 850 System Manual Section 2 Engineering Guidelines Table 2. BCU DIP-Switch S1 Options (Continued) Switch Function Description S1-2 Line Code Enables Bipolar Eight-Zero Substitution (B8ZS), which allows for Clear Channel operation for the T1 carrier system, or enables Alternate Mark Inversion (AMI). This option must be configured identically with all other T1 network equipment on this circuit.
Section 2 Engineering Guidelines Total Access 850 System Manual Faceplate Bantam Jack The faceplate bantam jack provides a means to monitor the network T1 connected to the rear of the Total Access 850 chassis. The jacks accept standard 310-type bantam plugs. Figure 2 display the bantam jack monitoring points.
Total Access 850 System Manual Section 2 Engineering Guidelines Faceplate CRAFT Interface Use the CRAFT port located on the RCU faceplate to configure the system via an EIA-232 connection. Table 3 displays the CRAFT port pinout. Table 3. T1 RCU CRAFT (DB-9, Female) Pinout Pin Name Description 1, 4, 6-9 UNUSED — 2 RD Receive Data (Output) 3 TD Transmit Data (Input) 5 SG Signal Ground Faceplate LEDs The faceplate LEDs provide status information using a color coded message format.
Section 2 Engineering Guidelines Total Access 850 System Manual Receiver Circuitry T1 T1 RX PAIR R1 Clock and Data Recovery Line Format Decoder To Backplane DJAT Line Format Encoder From Backplane MON IN Test Jack T1 T TX PAIR R Equalizer Transmitter Circuitry Local Loopback Point MON OUT Test Jack Line Loopback Point Payload/CSU Loopback Point Figure 4.
Total Access 850 System Manual Section 2 Engineering Guidelines Table 6. 3rd GEN T1 RCU Faceplate LEDs For these LEDs... This color light... Indicates that... T1 GREEN the network T1 interface is operational. RED the network T1 is in Red Alarm (meaning the T1 is down, not connected, or framing is improperly configured). AMBER the network T1 is in test mode (loopback). GREEN there is a valid 10 Mbps Ethernet link. AMBER there is a valid 100 Mbps Ethernet link.
Section 2 Engineering Guidelines Total Access 850 System Manual SDSL Router Controller Unit (1200377L1 and 1200377L2) The following is operational information pertaining to the SDSL Router Controller Unit when used with the Total Access 850 system. Faceplate CRAFT Interface Use the CRAFT port on the RCU faceplate to configure the system via an EIA-232 connection. Table 7 displays the CRAFT port pinout. Table 7.
Total Access 850 System Manual Section 2 Engineering Guidelines DIP-Switch Settings The Total Access 850 SDSL RCU uses DIP-switches to determine power-up start mode. Table 9 provides details for the DIP-switches. Table 9. SDSL RCU DIP-Switch S1 Options Switch Function Description S1-1 Firmware Mode ON* (down) The unit powers up in the firmware update mode. This mode is not used for normal operation. OFF Disables the firmware update mode.
Section 2 Engineering Guidelines Total Access 850 System Manual Table 10. Total Access 850 Backplane Connections Ref Des Device/Label Technology P1 wire-wrap strip clock/tests P2 50 pin amphenol FXO, FXS, etc.
Total Access 850 System Manual Section 2 Engineering Guidelines T1 Connection (JP2) The Total Access 850 provides dual T1 connection points. In all cases, only one of the connection points is used. When wire-wrapping of the T1 is utilized (using P3), a blank plug must be placed in the primary T1 connection (JP2). There is a potential of Class A3 T1 Span Power Voltage coming from the network.
Section 2 Engineering Guidelines Total Access 850 System Manual The DSX-1 interface pinout is shown in Table 13. Table 13. DSX-1 Network Connection Pinout Pin Name Description 1 R TXDATA-RING Transmit data from the network. 2 T TXDATA-TIP Transmit data from the network. 3 — UNUSED — 4 R1 RXDATA-RING Receive data toward the network. 5 T1 RXDATA-TIP Receive data toward the network.
Total Access 850 System Manual Section 2 Engineering Guidelines Nx56k/64k Port (J1) The Total Access 850 system provides a single V.35 Winchester-style connection on the rear of the chassis (as defined in Table 15). Table 15. V.
Section 2 Engineering Guidelines Total Access 850 System Manual Table 17. Alarm Notification Alarm Condition Relays Activated MJR MJVR Red Alarm X X Yellow Alarm X X AIS Alarm X X PSU Power Fuse Fails X X Alarms ACO Deactivates X X -48 ALM X Note: ACO will not deactivate MJR after a power fuse failure. Clock Wire-Wrap Strip (P1) A single wire-wrap strip is provided on the Total Access 850 backplane for connection to an external bits clock.
Total Access 850 System Manual Section 2 Engineering Guidelines T1 Wire-Wrap Connection (P3) Network T1 connections can have up to 140 VDC. Use caution when making T1 connections. There are two termination points for connecting the network T1 to the chassis: the primary RJ-48 connector (JP2) and the alternate wire-wrap pins on terminal strip P3 (see Figure 6 on page 33). Only one connector type is used (not both). The T1 primary connection is via the RJ-48 connector labeled T1 (JP2).
Section 2 Engineering Guidelines Total Access 850 System Manual 20 AWG RING LUG 16 AWG RING LUG RED 16 AWG STRANDED BLK -48V GRD BLK 20 AWG SOLID TO FUSE PANEL FG TO WIRE WRAP FRAME GROUND Figure 8. Alternate Power Connection 5. ACCESS MODULE INTERFACES Power Supply Unit (P/N 1175006L2) The PSU receives externally supplied -48 VDC from connectors P4 (normal) and P5 (alternate) on the rear of the unit. Connector P4 connects from an approved ADTRAN Power Supply and Battery Charger unit.
Total Access 850 System Manual Section 2 Engineering Guidelines Table 19. PSU Faceplate LEDs For these LEDs... This color light... Indicates that... POWER OFF the system is disconnected from the power source or powered off. GREEN the system is connected to a power source and is powered on. OFF ring generation is disabled for the system. GREEN ring generation is enabled for the system. OFF the system is in normal operation. Solid RED there is currently an active alarm condition.
Section 2 Engineering Guidelines Total Access 850 System Manual Interface Pinout Figure 9 shows the pinout connection for the amphenol connector. See Figure 7 on page 38 for closer detail.
Total Access 850 System Manual Section 2 Engineering Guidelines Table 21.
Section 2 Engineering Guidelines Total Access 850 System Manual Interface Pinout Figure 10 shows the pinout connection for the amphenol connector. See Figure 7 on page 38 for closer detail.
Total Access 850 System Manual Section 2 Engineering Guidelines Compliance Codes Table 25 provides the compliance codes for the Total Access 850 Quad FXO Module. Table 25. Quad FXO Module Compliance Codes CODE IN OUT Power Code (PC) C C Telecommunication Code (TC) – X Installation Code A – UBR1TE Access Module (P/N 1180020L1) Each port of the UBR1TE Access Module provides an ISDN U-interface and allows the transport of Basic Rate 2B+D information over the T1 carrier and twisted pair wiring.
Section 2 Engineering Guidelines Total Access 850 System Manual Interface Pinout Table 27 provides the interface pinout for the UBR1TE interface slot/amphenol connector assignment. Table 27.
Total Access 850 System Manual Section 2 Engineering Guidelines Table 28. BCU DIP-Switch S1 Options (Continued) Switch Function Description S1-2 Tandem Office Installation Indicates whether the unit is installed in a Tandem Office installation. S1-3 S1-4 S1-5 S1-6 64203376L1-1B Service for: S1-3: B1 S1-4: B2 S1-5: D Zero Byte Substitution ON LULT Mode – indicates an Adjacent-to-Customer configuration and sealing current should be provided (S1-1 ON).
Section 2 Engineering Guidelines Total Access 850 System Manual Specifications Table 29 provides the detailed specifications for the Total Access 850 UBR1TE Module. Table 29. UBR1TE Module Specifications Loop Interface (ANSI T1.601) Line 2-wire (tip and ring) Operating Mode full duplex Data Rate 160 kbps total; 144 kbps available to customer Signal Format 2B1Q Transmit Power 13 dBm to 14 dBm nominal DS1 Facility Interface BR1/10 compatible equipment.
Total Access 850 System Manual Section 2 Engineering Guidelines OCU DP Access Module (P/N 1180005L1) The OCU DP Access Module may be used for intra-building networks only. This interface should not be connected to public networks. The OCU DP module is a single port access module used to provide the interface between a DS0 time slot on the T1 and a 4-wire DDS device at the customer premises. The OCU DP supports up to 18 kft of copper for remote DSU connectivity.
Section 2 Engineering Guidelines Total Access 850 System Manual Dual V.35 Access Module (P/N 1180025L1) The Dual V.35 module provides additional V.35 interfaces for customer premises equipment. The module takes up two access slots; therefore three modules (six additional ports) can be added to an empty chassis. The Total Access 850 can support a maximum of seven V.35 interfaces. V.35 ports provided by the Dual V.35 module are accessed on the front of the Total Access 850.
Total Access 850 System Manual Section 2 Engineering Guidelines Table 34. Dual V.35 Interface Pinout (DB-26 to V.
Section 2 Engineering Guidelines Total Access 850 System Manual Compliance Codes Table 36 provides the compliance codes for the Total Access 850 Dual V.35 Module. Table 36. Dual V.35 Module Compliance Codes CODE IN OUT Power Code (PC) C C Telecommunication Code (TC) – – Installation Code A – DSX-1 Access Module (P/N 1200385L1) The DSX-1 interface provided on the DSX-1 Access Module may be used for intra-building networks only. This interface should not be connected to public networks.
Total Access 850 System Manual Section 2 Engineering Guidelines Table 37. DSX-1 Module Faceplate LEDs For these LEDs... This color light... Indicates that... Online OFF there is no power to the system. GREEN the DSX-1 signal is present and synchronized; the channel is configured for use. RED there is a present channel alarm on the T1 interface. Solid AMBER there is a channel test in progress. Blinking AMBER the card is initializing (during startup).
Section 2 Engineering Guidelines 54 Total Access 850 System Manual © 2004 ADTRAN, Inc.
NETWORK TURNUP PROCEDURE This section provides shipment contents list, grounding instructions, mounting options, and specifics of supplying power to the unit. CONTENTS Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Unpack and Inspect the SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Contents of ADTRAN Shipments . . . . . . . . . . . . . . . .
Section 3 Network Turnup Procedure 1. Total Access 850 System Manual INTRODUCTION This section discusses Total Access 850 installation. 2.
Total Access 850 System Manual Section 3 Network Turnup Procedure Contents of ADTRAN Shipments Your ADTRAN shipment of the Total Access 850 chassis includes the following items: • The Total Access 850 Base Unit • The Total Access 850 Series System CD • Wallmount brackets and screws • RJ-45 to RJ-45 8-pin cable (15 ft) - ADTRAN P/N 3125M008 • UL 1950 Notice Card - ADTRAN P/N 61200375L1-17 Customer must supply Ethernet cable and the DB-9 serial cable for configuration via the VT100 CRAFT interfaces. 4.
Section 3 Network Turnup Procedure Total Access 850 System Manual and the equipment grounding conductors serving these receptacles are to be connected to earth ground at the service equipment. A supplementary equipment grounding conductor shall be installed between the product or system and ground that is in addition to the equipment grounding conductor in the power supply cord.
Total Access 850 System Manual Section 3 Network Turnup Procedure DC Powered Systems The DC powered Total Access 850 comes equipped with a DC Power supply to furnish the voltages necessary for proper backplane operation. As shipped, the Total Access 850 is set to factory default conditions. After installing the chassis and any access modules, the Total Access 850 is ready for power-up. • • • • • • This unit shall be installed in accordance with Article 400 and 364.
Section 3 Network Turnup Procedure 7. Total Access 850 System Manual MOUNTING OPTIONS The Total Access 850 chassis may be wallmounted or installed in a 19-inch or 23-inch rack. Wallmount brackets are included with the chassis. For a rackmount installation, the Total Access 850 Base Unit allows flush-face mount, face-forward mount, center mount, and rear mount. The Total Access 850 chassis includes wallmount brackets.
Total Access 850 System Manual 8. Section 3 Network Turnup Procedure INSTALLING MODULES Figure 1 shows the slot numbering designation as viewed from the front of the Total Access 850 chassis. The functionally identical option slots only accept Total Access 850 access modules, and the controller slots only accept Total Access 850 controller modules. PSU RCU ACCESS MODULES Figure 1.
Section 3 Network Turnup Procedure Total Access 850 System Manual 3. Align the card edges to the guide grooves and insert the unit until the edge connector seats firmly into the backplane. 4. Lock the card in place by pushing in on the lock lever. 5. Reinstall the card-lock safety bar. Instructions for Installing the Total Access 850 Controller and Access Modules Individual access modules insert from the front. A locking bar holds the modules in place for added security.
Total Access 850 System Manual Section 3 Network Turnup Procedure OCU DP Access Module (P/N 1180005L1) Shipping Contents The ADTRAN shipment of the OCU DP Access Module includes the following items: • OCU DP Access Module • OCU DP Access Module Job Aid E&M/TO Access Module (P/N 1180402L1) Shipping Contents The ADTRAN shipment of the E&M/TO Access Module includes the following items: • E&M/TO Access Module • E&M/TO Access Module Job Aid Dual V.
Section 3 Network Turnup Procedure 64 Total Access 850 System Manual © 2004 ADTRAN, Inc.
USER INTERFACE GUIDE This section provides detailed descriptions of all menu options and configuration parameters available for the Total Access 850 when used with a Router Control Unit (RCU). This section does not apply to systems that employ a Bank Control Unit (BCU). This section of ADTRAN’s Total Access 850 System Manual is designed for use by network administrators and others who will configure and provision the system.
Section 4 User Interface Guide Total Access 850 System Manual FIGURES Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 7. Figure 10. Top-Level Terminal Menu Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Alternate Menu View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 System Info Menu . . . . . . . . . . . . . .
Total Access 850 System Manual 1. Section 4 User Interface Guide NAVIGATING THE TERMINAL MENU To access the terminal menus and management features of the Total Access 850, connect the unit to a VT100 terminal (or VT100 terminal emulator) via the CRAFT interface on the front of the unit or the rear CRAFT interface on the backplane. Configure the terminal settings for 9600 data rate, no parity, 8 data bits, 1 stop bit, and no flow control.
Section 4 User Interface Guide Total Access 850 System Manual horizontally across the window. To change the view, move your cursor to an index number and press . Figure 2 shows this alternate view. Fields and submenu names may vary slightly in this view. Figure 2. Alternate Menu View Window Pane Navigation Use the following chart to assist you in moving between and within the two window panes. 68 To do this... Press this key...
Total Access 850 System Manual Section 4 User Interface Guide Right Window Pane Notation The right window pane shows the contents of the currently selected menu. These contents include both submenu items and data fields. Some submenus contain additional submenus and some data fields contain additional data fields. The following chart explains the notation used to identify these additional items. This notation... Means that... [+] more items are available when selected.
Section 4 User Interface Guide Total Access 850 System Manual To do this... Press this key... Select items Arrows Edit a selected menu item Enter Cancel an edit Escape Close pop-up help screen Escape Move between the left and right panes Tab Arrows Move to the top of a screen A Move to the bottom of a screen Z Ascend one menu level Backspace Jump to terminal mode CTRL+T Jump to NAT menu CTRL+N Session Management Keystrokes To do this... Press this key...
Total Access 850 System Manual Section 4 User Interface Guide To do this... Press this key... Increment the value of certain types of fields by one when you paste information into those fields > Decrement the value of certain types of fields by one when you paste information into those fields < Save the current configuration immediately to RAM CTRL+W Insert a new list item For example, add a new item to the TELNET USER connection list by pressing while the cursor is over the index number.
Section 4 User Interface Guide Total Access 850 System Manual To do this... Go to this menu... Define, configure, and monitor all Total Access 850 Router functions ROUTER Configure security filters for L2 traffic and define RADIUS server parameters SECURITY Map data and voice ports (from integrated interfaces as well as installed modules) to network time slots DS0 MAPS Security Levels Password security levels only apply to Telnet connections.
Total Access 850 System Manual Section 4 User Interface Guide SYSTEM INFO The SYSTEM INFO menu provides basic information about the unit as well as data fields for editing information. Figure 3 displays the submenus that are available when you select this menu item. 0 Figure 3. System Info Menu SYSTEM INFO > SYSTEM NAME Provides a user-configurable text string for the name of the unit. This name can help you distinguish between different installations.
Section 4 User Interface Guide Total Access 850 System Manual SYSTEM INFO > UNIT NAME (Read only) Displays a product-specific name for the unit (such as TA 850 RCU). SYSTEM INFO > CLEI CODE (Read only) Displays the registered CLEI code for the unit. SYSTEM INFO > PART NUMBER (Read only) Displays the ADTRAN-specific part number for the unit. SYSTEM INFO > SERIAL NUMBER (Read only) Displays the serial number for the unit. The serial number of the Total Access 850 will automatically display in this field.
Total Access 850 System Manual Section 4 User Interface Guide SYSTEM CONFIG Set up the unit’s operational configuration from the SYSTEM CONFIG menu. Figure 4 shows the items included in this menu. Figure 4. System Config Menu SYSTEM CONFIG > MANAGEMENT Set up the CRAFT PORT, TELNET ACCESS, SNMP MANAGEMENT, and FDL MANAGEMENT from this menu. SYSTEM CONFIG > MANAGEMENT > CRAFT PORT Set up the CRAFT PORT parameters from this menu.
Section 4 User Interface Guide Total Access 850 System Manual Table 2. Instructions for Changing Passwords Step Action 1 Select the PASSWORD field—a new PASSWORD field displays. 2 Type the new password in the ENTER field. 3 Type the new password again in the CONFIRM field. SYSTEM CONFIG > MANAGEMENT > CRAFT PORT > IDLE TIME This option defines the amount of time in minutes user may stay connected without any activity on the CRAFT port before the user is automatically logged out of the system.
Total Access 850 System Manual Section 4 User Interface Guide SYSTEM CONFIG > MANAGEMENT > TELNET ACCESS > AUTHEN METHOD Set up the Telnet authentication method from this menu. The choices are LOCAL PASSWORD, RADIUS, LOCAL/RADIUS, and RADIUS/LOCAL. LOCAL/RADIUS indicates that the unit will try Local Password Authentication first, and if that fails, it will try Radius Authentication.
Section 4 User Interface Guide Total Access 850 System Manual Table 3. Telnet Security Levels Security Level Full Description The user has all access to view and configure all menus (same as logging in to the CRAFT port) Support The user has read only access to view the SYSTEM INFO menu. The user has privileges to view and change everything under the SYSTEM CONFIG menu except for the CRAFT port settings, Telnet access lists, and the SNMP management communities.
Total Access 850 System Manual Section 4 User Interface Guide SYSTEM CONFIG > MANAGEMENT > TELNET ACCESS > IP ACCESS LIST Set up the list of allowed Telnet managers. NETWORK ADDRESS Enter network addresses from which Telnet access to the unit is allowed. When a remote unit requests Telnet access to the unit, if the access list is empty or the remote’s IP address matches a list entry, remote access is granted. A network address of 0.0.0.0 with corresponding netmask 255.255.255.
Section 4 User Interface Guide Total Access 850 System Manual PRIVILEGE The access for this manager can be assigned three levels. The factory default is NONE. NONE No access is allowed for this community or manager. GET Manager can only read items. GET/SET Manager can read and set items. MANAGER IP This may be used in conjunction with the Netmask field to define a range of manager IPs. A netmask of 255.255.255.255 defines a single IP as the manager host IP. The default value is 0.0.0.0.
Total Access 850 System Manual Section 4 User Interface Guide SYSTEM CONFIG > MANAGEMENT > FDL MANAGEMENT > LINK IP ADDRESS This is the local IP address used for FDL management. The FDL uses a separate IP network for communication, distinct from the customer data that is configured under the ROUTER menus. The factory default is 0.0.0.0. SYSTEM CONFIG > MANAGEMENT > FDL MANAGEMENT > IP NETMASK This is the subnet mask defining the IP network used for FDL management. The factory default is 0.0.0.0.
Section 4 User Interface Guide Total Access 850 System Manual SYSTEM CONFIG > SYSLOG > SYSLOG FORMAT The SYSLOG FORMAT is the format of log messages. "ADTRAN" uses a format that is compatible with ADTRAN Utilities and forces the Syslog Facility to LOCAL0. UNIX uses the traditional Unix format and reports at the configured facility level. ADTRAN Utilities may malfunction if messages are received in the Unix format.
Total Access 850 System Manual Section 4 User Interface Guide SYSLOG using Terminal Mode Another option for configuring syslog is using the terminal mode command log dump . The logname must be all CAPS and be one of the following names: FATAL ALERT CRITICAL ERROR WARNING NOTICE INFO FILTER DEBUG The command will dump all messages for the indicated log (ALL LEVEL shows all log messages) stored in the internal log buffer to the command line display.
Section 4 User Interface Guide Total Access 850 System Manual SYSTEM CONFIG > SYSLOG > ARP LEVEL Minimum required level for sending ARP log messages. SYSTEM CONFIG > SYSLOG > UDP LEVEL Minimum required level for sending UDP log messages. SYSTEM CONFIG > SYSLOG > NETWRITE LEVEL This parameter is for ADTRAN internal use only. SYSTEM CONFIG > SYSLOG > TCP LEVEL Minimum required level for sending TCP log messages. SYSTEM CONFIG > SYSLOG > COMPSYS LEVEL This parameter is for ADTRAN internal use only.
Total Access 850 System Manual Section 4 User Interface Guide SYSTEM CONFIG > SYSLOG > CMCP LEVEL Minimum required level for sending log messages about communication with the CopperMountain DSLAM. Messages are only generated for ATM products. SYSTEM CONFIG > SYSLOG > SDSL LEVEL This parameter is for ADTRAN internal use only. SYSTEM CONFIG > SYSLOG > L1 LEVEL Minimum required level for sending log messages about WAN physical or Layer 1 connection.
Section 4 User Interface Guide Total Access 850 System Manual SYSTEM CONFIG > SYSLOG > ATM LEVEL Minimum required level for sending ATM log messages. Messages are only generated for ATM products. SYSTEM CONFIG > SYSLOG > COPPERCOM LEVEL Minimum required level for sending log messages about communication with the CopperCom Voice Gateway. Messages are only generated for ATM products.
Total Access 850 System Manual Section 4 User Interface Guide SYSTEM CONFIG > NETWORK TIME Activate the network time and configure the server type, time zone and various other network time parameters from this menu. SYSTEM CONFIG > NETWORK TIME > SERVER TYPE The unit time can be entered manually from the SYSTEM INFO menu, or the unit can receive time from an NTP/SNTP server. The NETWORK TIME menu includes all parameters relating to how the unit communicates with the time server.
Section 4 User Interface Guide Total Access 850 System Manual SYSTEM CONFIG > NETWORK TIME > STATUS This displays the current status of the time negotiation process. If an error is displayed, check all connections and configurations to try to resolve the problem. SYSTEM UTILITY Use the SYSTEM UTILITY menu to view and set the system parameters shown in Figure 5. Figure 5. System Utility Menu SYSTEM UTILITY > UPGRADE FIRMWARE Select the firmware upgrade method and perform upgrade from this menu.
Total Access 850 System Manual Section 4 User Interface Guide SYSTEM UTILITY > UPGRADE FIRMWARE > TRANSFER STATUS This appears when TFTP is used. It displays the status of the transfer as it happens. Any error or success message will be displayed here. SYSTEM UTILITY > UPGRADE FIRMWARE > START TRANSFER This activator is used when the configurable items in this menu are complete. This will initiate the transfer for either TFTP or XMODEM upgrades.
Section 4 User Interface Guide Total Access 850 System Manual SYSTEM UTILITY > CONFIG TRANSFER > CURRENT TRANSFER STATUS Indicates the current status of the update. SYSTEM UTILITY > CONFIG TRANSFER > PREVIOUS TRANSFER STATUS Indicates the status of the previous update. SYSTEM UTILITY > CONFIG TRANSFER > LOAD AND USE CONFIG Retrieves the configuration file specified in the TFTP SERVER FILENAME field from the server. To start this command, enter Y to begin or enter N to cancel.
Total Access 850 System Manual Section 4 User Interface Guide SYSTEM UTILITY > PING Activate the ping test and define the ping packet characteristics from this menu. SYSTEM UTILITY > PING > START/STOP Activator to start and cancel a ping test. Only one ping session can be active at a time. Diagnostic features such as ping, extended ping, traceroute, extended traceroute, and Telnet client can also be performed via TERMINAL MODE (see page 92).
Section 4 User Interface Guide Total Access 850 System Manual SYSTEM UTILITY > TRACEROUTE > MAXIMUM HOPS Specifies the maximum number of router exchanges allowed when traveling to the final destination (specified using the TRACE TARGET field) Range is 1 to 30. Default is 30. SYSTEM UTILITY > TRACEROUTE > TIMEOUT (IN SECS) Specifies the maximum delay (in milliseconds) given to a host (along a path to the final destination) to respond to the probe datagram sent before considering the packet a failure.
Total Access 850 System Manual Section 4 User Interface Guide timeout (seconds) Timeout in seconds (range 1-10) source (address or name) Source address or interface name to use noNat Do not NAT the ping packet Options may be entered in any order and may be truncated. Valid interface names are eth0, fdl0, ppp0, fr0, fr1, etc. Example usage: ping 10.0.0.5 r si 1500 so eth0 n This will ping with a repeat count of 10.
Section 4 User Interface Guide Total Access 850 System Manual INTERFACES Use the INTERFACES menu to view and configure parameters for the T1, ETHERNET, V.35, FXS, FXO, DSX-1 MODULE, and UBR1TE interfaces as shown in Figure 6. Figure 6. Interfaces Menus INTERFACES (NETWORK T1) View the network T1 interface status and configure T1 parameters from this menu. INTERFACES (T1) > CONFIG Configure the various T1 parameters and enable/disable loopbacks from this menu.
Total Access 850 System Manual Section 4 User Interface Guide INTERFACES (T1) > CONFIG > EQUALIZATION Select the line build out for the T1 interface. These are attenuation settings. 0 dB is the strongest signal, and the other settings make the T1 transmit signal weaker. The setting of this field depends on whether the circuit is provisioned for DS1 by the telephone company. The choices are 0 dB, -7.5 dB, -15 dB, -22 dB. Default is 0 dB.
Section 4 User Interface Guide Total Access 850 System Manual INTERFACES (T1) > STATUS > PERFORMANCE > CURRENT AND TOTALS > FS FS (Frame Slip) - A frame slip is defined as one or more frame bit errors in a one-second interval. INTERFACES (T1) > STATUS > PERFORMANCE > CURRENT AND TOTALS > LCV LCV (Line Code Violation) - A Line Code Violation is defined as a Bipolar Violation (BPV), not including the B8ZS code word if B8ZS is employed.
Total Access 850 System Manual Section 4 User Interface Guide INTERFACES (T1) > STATUS > ALARMS > ALARM HISTORY Displays the alarm history for the T1 interface. An asterisk in a field indicates that an alarm has occurred on the T1 interface since the last clear history. Refer to Interfaces (T1) > Status > Alarms > Current Alarms on page 96 for more details on listed alarm conditions.
Section 4 User Interface Guide Total Access 850 System Manual INTERFACES (DSX) View the integrated DSX interface status and configure T1 parameters from this menu. INTERFACES (DSX) > CONFIG Configure the various DSX parameters and enable/disable loopbacks from this menu. INTERFACES (DSX) > CONFIG > FORMAT This sets the frame format for the DSX interface. The setting must match the frame format of the circuit to which the interface is connected. Choices are ESF, SF (D4).
Total Access 850 System Manual Section 4 User Interface Guide INTERFACES (DSX) > STATUS > PERFORMANCE > CURRENT AND TOTALS > ES ES (Errored Second) - For ESF mode, an errored second is defined as a second with one or more Path Code Violations (PCVs), or one or more Out of Frame (OOF) defects, or one or more Controlled Slip events, or a detected AIS (blue alarm) defect. For D4 (SF) mode, the presence of Bipolar Violations (BPVs) also triggers an errored second.
Section 4 User Interface Guide Total Access 850 System Manual INTERFACES (DSX) > STATUS > ALARMS Displays current alarms and alarm history for the integrated DSX interface. INTERFACES (DSX) > STATUS > ALARMS > CURRENT ALARMS Displays the current alarms on the T1 interface. An asterisk in a field indicates that an alarm is active. LOS Loss of Signal. No signal detected on port interface. RED Not able to frame data received on the port. Alternately referred to as Out of Frame (OOF).
Total Access 850 System Manual Section 4 User Interface Guide INTERFACES (ETH) View the Ethernet interface status and configure the Ethernet parameters from this menu. INTERFACES (ETH) > CONFIG Configure the various Ethernet parameters from this menu. INTERFACES (ETH) > CONFIG > AUTO NEGOTIATION The Total Access 850 has the capability of auto negotiating the rate and duplex of the connected Ethernet link. Additionally, when this parameter is set to OFF, the rate and duplex are set manually.
Section 4 User Interface Guide Total Access 850 System Manual INTERFACES (V35) View the V.35 interface status and configure the V.35 parameters from this menu. INTERFACES (V35) > CONFIG Configure the DTE leads from this menu. INTERFACES (V35) > CONFIG > CTS Sets the control characteristic of the clear-to-send lead. Choices are NORMAL (follows RTS) or FORCE ON. Default is NORMAL. INTERFACES (V35) > CONFIG > DCD Sets the control characteristic of the carrier detect lead.
Total Access 850 System Manual Section 4 User Interface Guide INTERFACES (FXS) View the FXS interface status and configure the FXS parameters from this menu. INTERFACES (FXS) > CONFIG Configure the FXS mode, line impedance and Tandem parameters from this menu. INTERFACES (FXS) > CONFIG > SLOT Displays the slot number associated with the installed FXS Module. INTERFACES (FXS) > CONFIG > PORT Indicates the port on which the FXS is installed. INTERFACES (FXS) > CONFIG > MODE Choices are given below.
Section 4 User Interface Guide Total Access 850 System Manual INTERFACES (FXS) > CONFIG > TX (dB) Sets the TX direction level points. This signal will change the volume of the voice. TX (dB) is the signal that is transmitted out the T1, with 0 dB being the strongest. If the volume is too loud across the T1, this number should be increased. A higher number indicates more attenuation which equals lower volume. The value entered must be less than 10 dB. Default is 6.0 dB.
Total Access 850 System Manual Section 4 User Interface Guide INTERFACES (FXS) > CONFIG > TANDEM ANSWER SUPERVISION Causes the polarity of tip and ring to be reversed when the far-end answers. Can be enabled or disabled. Default is DISABLE. INTERFACES (FXS) > CONFIG > TANDEM > DNIS OPTIONS This parameter is used in conjunction with DNIS DELAY. Choices are DISABLE, ENABLE, and ENABLE W/ NO ANSWER WINK. Default is DISABLE.
Section 4 User Interface Guide Total Access 850 System Manual INTERFACES (FXS) > TEST Activate tests and monitor test status on a per port basis from this menu. INTERFACES (FXS) > TEST > SLOT Displays the slot number for the installed FXS Module. INTERFACES (FXS) > TEST > PORT Displays the port number. INTERFACES (FXS) > TEST > TEST Choices are given below. Default is NONE. NONE Indicates that no test is currently active.
Total Access 850 System Manual Section 4 User Interface Guide INTERFACES (FXO) View the FXO interface status and configure the FXO parameters from this menu. INTERFACES (FXO) > CONFIG Configure the FXO mode, line impedance, and Tandem parameters from this menu. INTERFACES (FXO) > CONFIG > SLOT Displays the slot number of the installed FXO Module. INTERFACES (FXO) > CONFIG > PORT Indicates the port on which the FXO is installed. INTERFACES (FXO) > CONFIG > MODE Choices are given below.
Section 4 User Interface Guide Total Access 850 System Manual INTERFACES (FXO) > CONFIG > SVC MODE Indicates whether the module is IN SERVICE or OUT OF SVC. This does not indicate whether the port has been mapped. For proper operation, the port must be mapped using the DS0 MAPS menu. Default is IN SERVICE. INTERFACES (FXO) > STATUS Displays the status of the FXO signal bits. INTERFACES (FXO) > STATUS > SLOT Displays the slot number for the installed FXO Module.
Total Access 850 System Manual Section 4 User Interface Guide INTERFACES (FXO) > TEST > TEST Choices are given below. Default is NONE. NONE Indicates that no test is currently active. DIGITAL NETWORK LPBK Used to loop back DS0 data coming from the network for each channel. Received data is latched in on the appropriate receive time slot on the receive bus. This data is then placed on the transmit bus in the unit’s transmit time slot.
Section 4 User Interface Guide Total Access 850 System Manual INTERFACE (DSX-1) > CONFIG > LINE CODE This setting must match the line code of the circuit to which the interface is connected. Choices are B8ZS (bipolar with 8-zero substitution) and AMI (alternate mark inversion). The default is B8ZS. INTERFACES (DSX-1) > STATUS Displays the DSX-1 interface status including performance data and alarm histories.
Total Access 850 System Manual Section 4 User Interface Guide INTERFACES (UBR1TE MODULE) View the UBR1TE Module interface status and configure the UBR1TE Module parameters from this menu. INTERFACES (UBR1TE) > CONFIG Configures the UBR1TE interface format and code from this menu. INTERFACE (UBR1TE) > CONFIG > SLOT Indicates the slot in which the UBR1TE Module is installed. INTERFACE (UBR1TE) > CONFIG > MODE Choices are LUNT, LUNT W/WAKEUP, and LULT.
Section 4 User Interface Guide Total Access 850 System Manual Sink positions. Default is LULT.
Total Access 850 System Manual Section 4 User Interface Guide INTERFACE (UBR1TE) > CONFIG > SEALING CURRENT DC sealing current is only applicable if the mode is LULT. Sealing current should be present for Adjacent-to-Customer applications. Default is ENABLED. INTERFACE (UBR1TE) > STATUS View the interface status information for the UBR1TE Module. INTERFACE (UBR1TE) > STATUS > SLOT Displays the slot number for the installed UBR1TE Module.
Section 4 User Interface Guide ADDR1 (LOCAL LPBK) ADDR2 ADDR3 ADDR4 NT1 Total Access 850 System Manual Loopbacks in the Network-to-Customer direction initiate from either the ISDN switch or the test menus. If a DS0 digital test set is connected to the bantam connector on the front of the module, data from the test set provides the 64 kbps test pattern used in testing B1 or B2. If no test set is connected, an internally generated 2074 test pattern is used.
Total Access 850 System Manual Section 4 User Interface Guide 1. Minimum of 35 transition in progress (TIP) bytes (*0111010). 2. Minimum of 35 LSC bytes: OCU (*1010101), CSU (*0110001). 3. Minimum of 100 loopback enable (LBE) bytes (*1010110). 4. Minimum of 32 far-end voice (FEV) bytes (*1011010). * denotes don’t care bit (either a 1 or a 0) Upon receipt of an OCU latching loopback, the UBR1TE provides a bilateral loopback on the bearer channel that received the loopback sequence.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 TDM FIRMWARE) Use the L2 protocol menu to select the L2 protocol, configure the protocol specific parameters and view the status as shown in Figure 8. The following menus are for Total Access 850 systems using T1 TDM firmware. Figure 8.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (T1 TDM FIRMWARE) – T1 INTERFACE Configure the L2 Protocol parameters and view the status of the T1 interface using items from this menu. L2 PROTOCOL (T1 TDM – T1) > PROTOCOL Configure the L2 protocol mode. Choices are PPP, FRE, HDLC, and AUTO (def). Selecting PPP configures the interface for Point-to-Point Protocol signaling on Layer 2. Selecting FRE configures the interface for frame relay signaling on Layer 2.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 TDM FIRMWARE) – T1 INTERFACE > PPP Configure the L2 PROTOCOL parameters and view the status of the T1 interface using PPP protocol from this menu. L2 PROTOCOL (T1 TDM–T1–PPP) > CONFIG Configure the L2 PROTOCOL parameters for the T1 interface using PPP protocol. L2 PROTOCOL (T1 TDM–T1–PPP) > CONFIG > MODE Select the L2 PROTOCOL mode. Choices are ROUTE IP, BRIDGE ALL, and ROUTE IP/BRIDGE OTHER. The default is ROUTE IP.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (T1 TDM–T1–PPP) > CONFIG > PPP > MAX TIMER (SEC) This value is the numbers of seconds to wait between unanswered configuration-requests. The possible values are 1 SEC, 2 SECS, 3 SECS (def), 5 SECS and 10 SECS. L2 PROTOCOL (T1 TDM–T1–PPP) > CONFIG > PPP > MAX FAILURE Due to the nature of PPP, configuration options may not be agreed upon between two PPP peers.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 TDM–T1–PPP) > STATUS > RX PKTS Number of packets received on the T1 interface. L2 PROTOCOL (T1 TDM–T1–PPP) > STATUS > TX BYTES Number of bytes transmitted on the T1 interface. L2 PROTOCOL (T1 TDM–T1–PPP) > STATUS > RX BYTES Number of bytes received on the T1 interface. L2 PROTOCOL (T1 TDM–T1–PPP) > STATUS > CURRENT UTIL (b/s) Current utilization of the T1 interface bandwidth presented in bits per second.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (T1 TDM FIRMWARE) – T1 INTERFACE > FRE PROTOCOL Configure the L2 PROTOCOL parameters and view the status of the T1 interface using Frame Relay protocol from this menu. L2 PROTOCOL (T1 TDM–T1–FRE) > CONFIG Configure the L2 PROTOCOL parameters for the T1 interface using the Frame Relay protocol. L2 PROTOCOL (T1 TDM–T1–FRE) > CONFIG > MAINTENANCE PROTOCOL The Frame Relay maintenance protocol is used on the WAN port.
Section 4 User Interface Guide Total Access 850 System Manual match occurs. If this default entry is not present, the unit falls back to using IARP to determine the protocols to use with that particular virtual circuit. If a static maintenance protocol is used, at least one DLCI mapping must be specified. To insert a new profile, press the I key when over the Num column. A new inserted profile will always be set up with the default parameters.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (T1 TDM–T1–FRE) > STATUS > PORT View the Frame Relay statistics on the WAN port. L2 PROTOCOL (T1 TDM–T1–FRE) > STATUS > PORT > PORT INDEX Integer used for identifying DLCIs on an interface. A single DLCI will always be port index 0. Subsequent DLCIs will have incrementing port indices.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 TDM–T1–FRE) > STATUS > PORT > LINK INTEGRITY STATUS TX FRAMES Number of Link-Integrity (LI) only frames transmitted out the WAN port. L2 PROTOCOL (T1 TDM–T1–FRE) > STATUS > PORT > LINK INTEGRITY STATUS RX FRAMES Number of LI only frames received on the WAN port. L2 PROTOCOL (T1 TDM–T1–FRE) > STATUS > PORT > DROP UNKNOWN DLCI Number of frames received that were not associated with any known PVC.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (T1 TDM–T1–FRE) > STATUS > PVC(S) > RX BYTES Number of Frame Relay bytes that have been received via this DLCI. L2 PROTOCOL (T1 TDM–T1–FRE) > STATUS > PVC(S) > DE COUNT Number of packets received on this DLCI with the Discharge Eligible (DE) bit set. L2 PROTOCOL (T1 TDM–T1–FRE) > STATUS > PVC(S) > CR COUNT Number of packets received on this DLCI with the Command Response (CR) bit set.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 TDM–T1–HDLC) > STATUS > RX PKTS Number of packets received on the T1 interface. L2 PROTOCOL (T1 TDM–T1–HDLC) > STATUS > TX BYTES Number of bytes transmitted on the T1 interface. L2 PROTOCOL (T1 TDM–T1–HDLC) > STATUS > RX BYTES Number of bytes received on the T1 interface. L2 PROTOCOL (T1 TDM–T1–HDLC) > STATUS > CURRENT UTIL (b/s) Current utilization of the T1 interface bandwidth presented in bits per second.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (T1 TDM–T1–AUTO) > STATUS > STATE This field represents the state of the auto detect/configuration function. The possible state are: OFF The T1 interface is down, so the auto-detect/configuration process is currently idle. DETECTING L2 PROTOCOL The T1 interface is up and waiting for the first control/signaling packet.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 ATM FIRMWARE) Use the L2 PROTOCOL menu to select the L2 PROTOCOL, configure the protocol specific parameters, and view the status as shown in Figure 8. The following menus are for Total Access 850 systems using T1 ATM firmware. Figure 9.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (T1 ATM FIRMWARE) – T1 INTERFACE Configure the L2 PROTOCOL parameters and view the status of the T1 interface using items from this menu. L2 PROTOCOL (T1 ATM – T1) > PROTOCOL Configure the L2 PROTOCOL mode. Choices are ATM and CUMTN (def). Selecting ATM configures the interface for Asynchronous Transfer Mode signaling on Layer 2. Selecting CUMTN configures the interface for Copper Mountain frame relay signaling on Layer 2.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 ATM–T1–ATM) > CONFIG > ATM CONFIG > DATA SCRAMBLING DATA SCRAMBLING can be ENABLED or DISABLED for cell traffic. Configuring this setting incorrectly for a particular circuit will cause poor performance at the ATM Layer. The setting must match the configuration setting of the ATM switch or DSLAM at the other end of the circuit.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (T1 ATM–T1–ATM) > CONFIG > PVC CONFIG > VCI This is the ATM Virtual Channel Identifier that serves as an address for the virtual channel cell transmissions between two devices. The range is 0-65355. The default setting is 38. L2 PROTOCOL (T1 ATM–T1–ATM) > CONFIG > PVC CONFIG > CONNECTION Select the physical and logical method of data transfer over the virtual path. There are three valid connection entries: ROUTER, V35, and VOICE.
Section 4 User Interface Guide Total Access 850 System Manual TX METHOD Specifies the method the Total Access 850 uses to obtain PPP authentication from the peer. There are four possible selections: NONE The connection will not allow the PPP peer to authenticate it. PAP, CHAP, OR EAP The unit will ask for EAP during the first PPP LCP negotiation and allow the PPP peer to negotiate down to CHAP or PAP.
Total Access 850 System Manual Section 4 User Interface Guide MAX CONFIG This value is the number of unanswered configuration-requests that should be transmitted before resetting PPP negotiations. the possible values are 5, 10, 15, and 20 (def). MAX TIMER (SEC) This value is the number of seconds to wait between unanswered configuration-requests. The possible values are 1 SEC, 2 SECS, 3 SECS (DEF), 5 SECS, and 10 SECS.
Section 4 User Interface Guide Total Access 850 System Manual CONNECTION (V35) > SETUP > SETUP > PROTOCOL MAPPING Network providers have the ability to provision each PVC pair with an encapsulation mode to ensure interoperability between terminal equipment. The choices are TRANSPARENT or TRANSLATION (def). TRANSLATION mode is most common and carries multiple upper layer protocols over Frame Relay and ATM PVCs.
Total Access 850 System Manual Section 4 User Interface Guide CONNECTION (VOICE) > SETUP > CALL CONTROL The Call Control setting is used to configure the correct Voice Gateway protocol for voice signaling control between the Total Access 850 and the configured Gateway. The CALL CONTROL setting must be configured correctly before the voice circuits will work correctly. The Total Access 850 supports Jetstream, Coppercom, Tollbridge, and LES-CAS. The default is LES-CAS.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 ATM–T1–ATM) > STATUS > ATM STATUS Displays overall ATM link performance statistics. The following statistics are available: AP: TX CELLS Number of cells transmitted over the ATM link. AP: RX CELLS Number of cells received over the ATM link. AP: RX OAM CELLS Number of Operation, Administration, and Maintenance cells received on the ATM link.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (T1 ATM–T1–ATM) > STATUS > PVC STATUS > SUB-INTERFACE The T1 SUB-INTERFACE is ATM[0.0], representing the T1 physical and logical ports, respectively. This is a read-only field. L2 PROTOCOL (T1 ATM–T1–ATM) > STATUS > PVC STATUS > AAL STATS Shows the statistics of ATM Adaptation Layer frames. MAX PDU SIZE Maximum Protocol Data Unit size for the ATM AAL5 frame.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 ATM–T1–ATM) > STATUS > PVC STATUS > PROTOCOL STATUS Use these menus to view the AAL2 STATS, POTS STATS, and to CLEAR STATS for the PVC Protocol. AAL2 STATS ATM Adaptation Layer 2 statistics is used to provide error information on voice traffic. This menu displays RX AAL2 HEC ERRORS, RX AAL2 SEQK ERRORS, RX VOICE SEQ ERRORS, RX VOICE BAD CID, RX VOICE BAD UUI, RX VOICE EOC CELLS, and PEAK CELL RATE.
Total Access 850 System Manual Section 4 User Interface Guide POTS STATS Selecting this menu options will show real-time indication status of each voice port on the Total Access 850. On a per port basis, the user can determine which ports are active/inactive as well as view other statistics like TXQ, INSERTS and DROPS INDICATORS. The Echo Canceller module ADPCM functionality automatically shifts ON/OFF when fax or modem calls are placed.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 ATM–T1–CUMTN) > CONFIG Configure the L2 PROTOCOL parameters for the T1 interface using Copper Mountain Frame Relay protocol. To insert a new profile, press the I key when over the NUM column. A new inserted profile will always be set up with the default parameters. To copy parameters from an old profile to this newly inserted profile, use the copy (C) and paste (P) keys. Entire configuration trees can be copied with this method.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (T1 ATM–T1–CUMTN) > STATUS View the status of the Copper Mountain DLCI connections. L2 PROTOCOL (T1 ATM–T1–CUMTN) > STATUS > NUM Displays the index number for the Status menu entries. L2 PROTOCOL (T1 ATM–T1–CUMTN) > STATUS > SUB-INTERFACE The T1 SUB-INTERFACE is CuMtn[0.0] when the L2 PROTOCOL is set for CUMTN FRE. The [0.0] represents the T1 physical and logical ports respectively. This is a read-only field.
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (T1 ATM – V35) > CONFIG > UNI MAINT PROTOCOL Specifies the maintenance protocol or signaling protocol between the local V.35 port and the attached DTE port. The choices are ANNEX D (def), ANNEX A, LMI, and STATIC. L2 PROTOCOL (T1 ATM – V35) > CONFIG > UNI POLL TIMEOUT T392 (5-30) T392 for signaling protocol. This parameter has no meaning if the UNI MAINT PROTOCOL is set to STATIC (no signaling). The default setting is 10.
Total Access 850 System Manual Section 4 User Interface Guide CR COUNT Number of packets received on an individual DLCI with the CR bit set BECN COUNT Number of packets received on an individual DLCI with the BECN bit set FECN COUNT Number of packets received on an individual DLCI with the FECN bit set UNKNOWN FRAME RX Frames received that were not associated with any PVC entries L2 PROTOCOL (T1 ATM FIRMWARE) – DSX INTERFACE Configure the L2 PROTOCOL parameters and view the status of the integrate
Section 4 User Interface Guide Total Access 850 System Manual L2 PROTOCOL (ALL FIRMWARE) – ETH INTERFACE > 802.3 PROTOCOL Configure the L2 PROTOCOL parameters and view the status of the Ethernet interface from this menu. L2 PROTOCOL (ALL–ETH–802.3) > PROTOCOL Displays the L2 PROTOCOL for the 10/100BaseT Ethernet port. Currently only 802.3 is supported. L2 PROTOCOL (ALL–ETH–802.3) > CONFIG Configure the mode for this 10/100BASET Ethernet port from this menu. L2 PROTOCOL (ALL–ETH–802.
Total Access 850 System Manual Section 4 User Interface Guide L2 PROTOCOL (ALL–ETH–802.3) > STATUS > RX ERRORS Number of packets received in error and dropped. L2 PROTOCOL (ALL–ETH–802.3) > STATUS > CRCS Number of packets detected with CRC errors. L2 PROTOCOL (ALL–ETH–802.3]) > STATUS > RX COLLISIONS Number of collisions which occurred during reception. L2 PROTOCOL (ALL–ETH–802.3) > STATUS > NON-ALIGNED The NON-ALIGNED parameter is set when the number of bits received is not divisible by 8.
Section 4 User Interface Guide Total Access 850 System Manual BRIDGE > CONFIG > INTERFACES (T1) Configure the T1 interface bridging parameters from this menu. BRIDGE > CONFIG > INTERFACES (T1) > SUB-INTERFACE The T1 sub-interface is PPP [0.0] if the L2 PROTOCOL is set for PPP. The [0.0] represents the T1 physical and logical ports respectively. This is a read-only field. The T1 sub-interface is FRE [0.X] if the L2 PROTOCOL is set fro FRAME RELAY. The [0.
Total Access 850 System Manual Section 4 User Interface Guide BRIDGE > STATUS > BRIDGE TABLE > TTL Time to Live (TTL) is the number of seconds until the address is removed from the table. This is a read only field. 64203376L1-1B © 2004 ADTRAN, Inc.
Section 4 User Interface Guide Total Access 850 System Manual ROUTER Configure the router parameters and view routing statistics from this menu as shown in Figure 8. Figure 11. Router Menu ROUTER > CONFIG Configure the interfaces, routes, DHCP Server, and UDP Relay options from this menu. ROUTER > CONFIG > INTERFACES Configure the layer 3 options for the Ethernet and T1 interfaces from this menu.
Total Access 850 System Manual Section 4 User Interface Guide ROUTER > CONFIG > INTERFACES (ETH)> SETUP Configure the Ethernet addressing, RIP, and Proxy ARP from this menu. PRIMARY IP This is used to setup the IP addresses for the LAN on the unit. IP ADDRESS The IP address assigned to the unit's Ethernet port is set here. This address must be unique within the network. Default is 10.0.0.1. SUBNET MASK This is the IP network mask that is to be applied to the unit's Ethernet port. Default is 255.255.
Section 4 User Interface Guide Total Access 850 System Manual V2 SECRET Enter the secret used by RIP version 2 here. PROXY ARP This feature allows the network portion of a group of addresses to be shared among several physical network segments. The ARP protocol provides a way for devices to create a mapping between physical addresses and logical IP addresses.
Total Access 850 System Manual Section 4 User Interface Guide ROUTER > CONFIG > INTERFACES (NET) > SUB-INTERFACE This is a read-only field which displays the physical and logical port of the interface using the following nomenclature: [A.B], where A represents the physical port (network interface is 0, Ethernet is 1) and B represents the logical port for the Layer 2 protocol (i.e. PVC for Frame Relay, PPP link, etc.
Section 4 User Interface Guide Total Access 850 System Manual FAR-END IP ADDRESS This is the address of the NEXT hop router on this interface. This field is only visible when ADDRESS MODE is set to USER SPECIFIED. MTU Specifies the maximum size for a packet transmitted on this PVC. Default is 1500. This field is only valid when L2 protocol for this sub-interface is FRE. NAT Use this menu to set up and use Network Address Translation on this interface.
Total Access 850 System Manual Section 4 User Interface Guide PUBLIC ADDRESS MODE Choose NAPT ADDR (default) or SPECIFIED to choose which address to use for this translation. Choosing SPECIFIED allows the user to define a different public IP address to use for this translation. PUBLIC ADDRESS This menu appears when the PUBLIC ADDRESS MODE is set to SPECIFIED, and allows the user to enter a specific IP address as the NAPT address for this translation.
Section 4 User Interface Guide Total Access 850 System Manual PUBLIC PORT MODE This option appears when the PROTOCOL MODE is configured with a single protocol (such as TCP, UDP, or ICMP). Choices are ANY PORT (default) and SPECIFIED. The public destination port associated with this entry can be specified to add more control over certain types of traffic. Leave this configured as ANY PORT to cover all port types. PUBLIC PORT This menu appears when the PUBLIC PORT MODE is set to SPECIFIED.
Total Access 850 System Manual Section 4 User Interface Guide PRIVATE PORT MODE Select ANY PORT (default) or a SPECIFIED port number for this translation. The private destination port associated with this entry can be specified to provide more control over certain types of traffic. Leave configured as ANY PORT to cover all port types.
Section 4 User Interface Guide Total Access 850 System Manual SPOOFED PORT Spoofed port number for the translation. The Total Access 850 often needs to use the spoofed ports to determine which private device to translate the packet to. This would be necessary if multiple applications using the same private port were occurring simultaneously. SERVER PORT Port number used by the server (public device). TOTAL TIME UNUSED Time the translation has been unused, in seconds.
Total Access 850 System Manual Section 4 User Interface Guide METHOD Specifies the way the RIP protocol sends out its advertisements. The following options are available: SPLIT HORIZON (Default) Only routes not learned from this circuit are advertised. POISON REVERSE All routes are advertised, but the routes learned from this point are “poisoned” with an infinite metric. DIRECTION Allows the direction at which RIP advertisements are sent and received to be specified.
Section 4 User Interface Guide Total Access 850 System Manual GATEWAY The IP address of the router to receive the forwarded IP packet. Default is 0.0.0.0. HOPS The number of router hops required to get to the network or host. Maximum distance is 16 hops. Default is 1. PRIVATE When set to NO, the unit will advertise this static route using RIP. Setting to YES means that the route is kept private. Default is NO. ROUTER > CONFIG > DHCP SERVER Use this menu to set up the DHCP server.
Total Access 850 System Manual Section 4 User Interface Guide NETWORK ADDRESS Defines the network address for the configured address pool (for example, 172.24.0.0). The NETWORK ADDRESS and NETWORK MASK determine the number of addresses available on the network for the configured pool. NETWORK MASK Defines the network mask associated with the network address for the configured address pool (for example, 255.255.0.0).
Section 4 User Interface Guide Total Access 850 System Manual NBNS SERVER (PRI) Defines the primary NetBIOS Windows Internet Naming Service (WINS) name server IP address (in dotted decimal notation) available for use by the Dynamic Host Configuration Protocol (DHCP) clients. NBNS SERVER (SEC) Defines the secondary NetBIOS Windows Internet Naming Service (WINS) name server IP address (in dotted decimal notation) available for use by the Dynamic Host Configuration Protocol (DHCP) clients.
Total Access 850 System Manual Section 4 User Interface Guide ROUTER > CONFIG > UDP RELAY This menu configures the unit to act as a UDP relay agent for applications requiring a response from UDP hosts that are not on the same network segment as their clients. ROUTER > CONFIG > UDP RELAY > MODE When this option is set to ON, the unit will act as a relay agent. Default is OFF. ROUTER > CONFIG > UDP RELAY > UDP RELAY LIST Up to four relay destination servers can be specified in this list.
Section 4 User Interface Guide Total Access 850 System Manual ROUTER > STATUS > IP ROUTES > PORT Port gateway is located on: LOCAL Sent directly to the unit’s router ETH0 The unit’s Ethernet port WAN0 The unit’s first PPP bundle FR 0 . . . FR 9 The unit is connected up to 10 DLCIs ROUTER > STATUS > IP ROUTES > USE Number of times the unit has referenced the route.
Total Access 850 System Manual Section 4 User Interface Guide • IP • ICMP • TCP • UDP All of these statistics are taken from the MIB-II variables in RFC 1156. To clear the accumulated statistics, press the key on CLEAR COUNTS. ROUTER > STATUS > IP STATS > IP View the IP statistics from this menu. DEFAULT TTL The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this unit, whenever a TTL value is not supplied by the transport layer protocol.
Section 4 User Interface Guide Total Access 850 System Manual DATAGRAMS DISCARDED The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly. SENT DATAGRAMS TO UPPER LYERS The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).
Total Access 850 System Manual Section 4 User Interface Guide SUCCESSFUL FRAGMENTS The number of IP datagrams that have been successfully fragmented at this unit. FAILED FRAGMENTS The number of IP datagrams that have been discarded because they needed to be fragmented at this unit but could not be e.g., because their “Don't Fragment” flag was set. TOTAL IP FRAGMENTS The number of IP datagram fragments that have been generated as a result of fragmentation at this unit.
Section 4 User Interface Guide Total Access 850 System Manual ICMP REDIRECTED MESSAGES RCVD The number of ICMP Redirect messages received. ICMP ECHO REQUEST MSGS RCVD The number of ICMP Echo (request) messages received. ICMP ECHO REPLY MSGS RCVD The number of ICMP Echo Reply messages received. ICMP TIMESTAMP REQUEST MSGS RCVD The number of ICMP Timestamp (request) messages received. ICMP TIMESTAMP REPLY MSGS RCVD The number of ICMP Timestamp Reply messages received.
Total Access 850 System Manual Section 4 User Interface Guide ICMP PARAMETER PROBLEM MSGS SENT The number of ICMP Parameter Problem messages sent. ICMP SOURCE QUENCH MSGS SENT The number of ICMP Source Quench messages sent. ICMP REDIRECT MSGS SENT The number of ICMP Redirect messages sent. ICMP ECHO REQUEST MSGS SENT The number of ICMP Echo (request) messages sent. ICMP ECHO REPLY MSGS SENT The number of ICMP Echo Reply messages sent.
Section 4 User Interface Guide Total Access 850 System Manual NO APPLICATION AT DEST. PORT The total number of received UDP datagrams for which there was no application at the destination port. UDP BAD PACKETS The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port. UDP DATAGRAMS SENT The total number of UDP datagrams sent from this unit. CLEAR COUNTS Selecting this activator clears the UDP statistics.
Total Access 850 System Manual Section 4 User Interface Guide MAX TCP CONNECTIONS The limit on the total number of TCP connections the unit can support. In entities where the maximum number of connections is dynamic, this object should contain the value -1. ACTIVE TCP CONNECTIONS The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state.
Section 4 User Interface Guide Total Access 850 System Manual ROUTER > STATUS > IP STATS > TCP CONNS View the TCP Conns Statistics from this menu. This table shows the different states of each TCP connection. STATE The possible states are FREE, CLOSED, LISTEN, SYNC SENT, SYNC RECEIVED, ESTABLISHED, FINWAIT1, FINWAIT2, CLOSEWAIT, LASTACK, CLOSING, and TIMEWAIT. LOCAL IP ADDRESS Local IP address of the TCP connection. LOCAL PORT Local port of the TCP connection.
Total Access 850 System Manual Section 4 User Interface Guide Figure 12. Security Menu 64203376L1-1B © 2004 ADTRAN, Inc.
Section 4 User Interface Guide Total Access 850 System Manual SECURITY > FILTERS Configure the filter characteristics from this menu. SECURITY > FILTERS > FILTER DEFINES The unit can filter packets based on certain parameters within the packet. The method used by the unit allows the highest flexibility for defining filters and assigning them to a PVC or PPP link. The filters are set up in two steps: (1) defining the filter types, and (2) applying them to a list under the PVC or PPP configuration.
Total Access 850 System Manual Section 4 User Interface Guide DEST MASK Bits in the MAC destination address used for comparison. Values are in hexadecimal format. Default is 00:00:00:00:00:00. TYPE 16-bit type field used for comparison. Values are in hexadecimal format. Default is 00:00. TYPE MASK Bits in the type field used for comparison. Values are in hexadecimal format. Default is 00:00.
Section 4 User Interface Guide Total Access 850 System Manual NUM Indicates the entry number in the IP Filter Defines table. NAME Identifies the filter entry. Default is no entry in name field. FILTER TYPE Specifies a NORMAL or DEBUG filter. When a NORMAL filer is applied to an interface, traffic is blocked or forwarded according to the filter. When a DEBUG filter is applied, packets that match the filter are documented without affecting traffic flow.
Total Access 850 System Manual Section 4 User Interface Guide DEST PORT IP destination port number used for comparison. Value is in decimal format. Range: 0 - 65535. Default is 0. DEST PORT COMP Type of comparison that is performed. Default is NONE. = means ports equal to NOT = means port not equal to > means port greater than < means port less than None - means the source port is not compared PROTOCOL Protocol used for comparison. Value is in decimal format. Range: 0 - 255. Default is 0.
Section 4 User Interface Guide Total Access 850 System Manual SECURITY > FILTERS > INTERFACES (ETH) > SUB-INTERFACE The Ethernet sub-interface is 802.3[1.0]. This is a read-only field. SECURITY > FILTERS > INTERFACES (ETH) > SET-UP Enable the Ethernet interface filtering and define filters from this menu. IN FROM VC The packets which come into the unit can be filtered in three ways: DISABLE (DEF) Turns off packet input filtering. No incoming packets are blocked.
Total Access 850 System Manual Section 4 User Interface Guide NEXT OPER The next operation to use to combine with the next filter in the list (default is END). END the last filter to combination. AND logically AND this filter with the next filter in the list. OR logically OR this filter with the next filter in the list. HIT COUNT Displays the number of packets that match the criteria for the defined filter.
Section 4 User Interface Guide Total Access 850 System Manual FILTER LIST NAME Selects between filters defines in the list. Default is no entry in filter list name. NEXT OPER The next operation to use to combine with the next filter in the list (default is END): END the last filter to combination. AND logically AND this filter with the next filter in the list. OR logically OR this filter with the next filter in the list.
Total Access 850 System Manual Section 4 User Interface Guide SECURITY > RADIUS SERVER > RETRY COUNT (1-10) This is the number of times the unit should send a request packet tho the RADIUS SERVER without a response before giving up. If the number of attempts to communicate with the primary server is equal to the retry count, the second server (if defined) is tried. If the second server does not respond within the retry count the third server (if defined) is tried.
Section 4 User Interface Guide Total Access 850 System Manual DS0 MAPS > ACTIVE MAP Activates one of the two dedicated maps (MAP 1 or MAP 2), or the DUAL T1 MAP. In the DUAL T1 mode, the built-in DSX-1 interface DSX[3] can be utilized as a secondary T1 connection. In DUAL T1 mode, the second T1 is limited to voice connections on FXS and FXO modules. For example, the user may map all 24 DS0s on the network T1 to the router, and on the second T1 (DSX-1 interface) map all 24 DS0s to the FXS cards.
Total Access 850 System Manual Section 4 User Interface Guide DS0 MAPS > EDIT/VIEW MAP 1 > RBS Robbed Bit Signaling. Default is N/A. Once a SLOT and port are assigned, this will automatically change to ON or OFF. The unit automatically assigns OFF where RBS is not an option. ON preserves the signaling bits between the connections. OFF ignores the signaling bits. For the FXS, RBS defaults to ON. The RBS parameter remains at N/A for the TA IAD, because RBS is not applicable to data connections.
Section 4 User Interface Guide 4. Total Access 850 System Manual APPENDICES (T1 TDM APPLICATIONS) Appendix A. Configuring the Unit for Routing Initial Setup It is best to configure Total Access 850 TDM applications by following the order of the top-level menus. For example, first configure the system parameters using the SYSTEM INFO and SYSTEM CONFIG menus. Next, configure the Layer 1 parameters using the INTERFACES menu.
Total Access 850 System Manual Section 4 User Interface Guide Ethernet Interface Setup Instructions Most applications should not require a manual setup for the Ethernet interface. By default, the Ethernet interface is configured to auto-detect the data rate (as either 10 or 100 Mbps). The following steps disable the auto-negotiation parameter and manually configure the interface. Step Action 1 From the main menu, select INTERFACES. 2 Highlight the CONFIG menu for the ETH interface and press .
Section 4 User Interface Guide Total Access 850 System Manual Layer 2 Protocol (FRE) Configuration – T1 Interface (Continued) 7 Set DLCI to the DLCI number. This DLCI should match what is programmed in the network Frame Relay switch. 8 Set mode to ROUTE IP. Using this menu you also have the option to route only IP packets and bridge all other data packets (ROUTE IP/BRIDGE OTHER) or bridge all data packets on this PVC (BRIDGE ALL). 9 Left arrow back to the main menu to save the changes.
Total Access 850 System Manual Section 4 User Interface Guide Layer 2 Protocol Configuration – Ethernet Interface 3 Set mode to ROUTE IP. Using this menu you also have the option to route only IP packets and bridge all other data packets (ROUTE IP/BRIDGE OTHER) or bridge all data packets on this connection (BRIDGE ALL). Refer to L2 Protocol (ALL–ETH–802.3) > Config > Mode on page 144 for more details. 4 Left arrow back to the main menu to save the changes. 3.
Section 4 User Interface Guide Total Access 850 System Manual Router Options – T1 Interface (L2 Protocol = FRE or PPP) Step Action 1 From the main menu, select ROUTER and press . 2 Use the right arrow key to highlight CONFIG and press . 3 Select INTERFACES and press . Use the right arrow key to highlight the SETUP field for the T1 interface and press .
Total Access 850 System Manual Section 4 User Interface Guide DS0 Mapping Instructions Step 1 Action From the main menu, select DS0 MAPS. Verify that the ACTIVE MAP is set to either MAP 1 or MAP 2. This is the map that is actively running on the unit. The unit has the ability to store two maps. 2 • To edit the current map, press on EDIT/VIEW MAP 1 to view the map. (If Map 1 is the Active Map) • To edit the standby map, press on EDIT/VIEW MAP 2 to view the map.
Section 4 User Interface Guide Total Access 850 System Manual Appendix B. Configuring the Unit for Bridging Initial Setup It is best to configure Total Access 850 TDM applications by following the order of the top-level menus. For example, first configure the system parameters using the SYSTEM INFO and SYSTEM CONFIG menus. Next, configure the Layer 1 parameters using the INTERFACES menu. Once the Layer 1 information is configured, proceed to the Layer 2 setup using the L2 PROTOCOL menus.
Total Access 850 System Manual Section 4 User Interface Guide Ethernet Interface Setup Instructions Most applications should not require a manual setup for the Ethernet interface. By default, the Ethernet interface is configured to auto-detect the data rate (as either 10 or 100 Mbps). The following steps disable the auto-negotiation parameter and manually configure the interface. Step Action 1 From the main menu, select INTERFACES. 2 Highlight the CONFIG menu for the ETH interface and press .
Section 4 User Interface Guide Total Access 850 System Manual Layer 2 Protocol (FRE) Configuration – T1 Interface (Continued) 7 Set DLCI to the DLCI number. This DLCI should match what is programmed in the network Frame Relay switch. 8 Set mode to BRIDGE ALL. Using this menu you also have the option to route only IP packets and bridge all other data packets (ROUTE IP/BRIDGE OTHER) or route all IP data packets on this PVC (ROUTE IP). 9 Left arrow back to the main menu to save the changes.
Total Access 850 System Manual Section 4 User Interface Guide 3. Verifying the Bridge Options For more details on the configuration parameters discussed in this section, refer to the following pages: Bridge menus beginning on page 145 Bridge Options Step Action 1 From the main menu, select BRIDGE and press . 2 Use the right arrow key to highlight CONFIG and press . 3 Select INTERFACES and press . Verify that the desired interface is listed in this table.
Section 4 User Interface Guide Total Access 850 System Manual DS0 Mapping Instructions (Continued) 192 5 Set the PORT of the DS0 that you are mapping to ROUTER 64K or ROUTER 56K. 6 Map all the DS0s as desired, and exit this menu by pressing the left arrow button. Your changes will automatically save when exiting the map. 7 Make sure the ACTIVE MAP is set to the correct map (the map you want running) before exiting the DS0 MAPS menu. 8 Left arrow back to the main menu. © 2004 ADTRAN, Inc.
Total Access 850 System Manual Section 4 User Interface Guide Appendix C. Configuring the Unit for Voice Applications Initial Setup It is best to configure Total Access 850 TDM applications by following the order of the top-level menus. For example, first configure the system parameters using the SYSTEM INFO and SYSTEM CONFIG menus. Next, configure the Layer 1 parameters using the INTERFACES menu. Once the Layer 1 information is configured, proceed to the Layer 2 setup using the L2 PROTOCOL menus.
Section 4 User Interface Guide Total Access 850 System Manual FXS Interface Setup Instructions Step Action 1 From the main menu, select INTERFACES. 2 Highlight the CONFIG menu for the FXS interface and press . 3 Right arrow to select MODE and choose LOOP START, GROUND START, TANDEM (E&M), TR08 SINGLE, TR08 UVG, or DPO. This mode should be set based on the network configuration and the operation of each FXS port. All FXS ports are independent and do not need to have the same mode.
Total Access 850 System Manual Section 4 User Interface Guide FXS Interface Setup Instructions (Continued) 11 Press on the TANDEM [+] option to view the TANDEM options if the port mode is set to TANDEM (E&M). 12 Set the CONVERSION MODE of the port to either LOOP START or GROUND START. 13 Set the SUPERVISION of the port to either IMMEDIATE or WINK. Be sure to set the TANDEM options for each port set to TANDEM E&M. 2.
Section 4 User Interface Guide Total Access 850 System Manual Appendix D. Configuring the Unit for DSX-1 Applications The Total Access 600 Series systems are available with an integrated DSX-1 interface for both voice and data applications. Regardless of the application (either voice or data), the Total Access 850 has the ability to map DS0s from the network T1 to DS0s on the DSX-1 interface (cross-connect) without affecting the data present on the DS0s.
Total Access 850 System Manual Section 4 User Interface Guide T1 Interface Setup Instructions (Continued) This line code must match the line code used by the other units in the network. 5 Set the EQUALIZATION or line build out. The default setting of 0 DB is usually sufficient. 6 Set the CSU LPBK option to ENABLE, DISABLE, or DISABLE ALL based on whether looping to this unit from another unit will be allowed. DSX-1 Interface Setup Instructions Step Action 1 From the main menu, select INTERFACES.
Section 4 User Interface Guide Total Access 850 System Manual DS0 Mapping Instructions Step 1 Action From the main menu, select DS0 MAPS. Verify that the ACTIVE MAP is set to either MAP 1 or MAP 2. This is the map that is actively running on the unit. The unit has the ability to store two maps. 2 • To edit the current map, press on EDIT/VIEW MAP 1 to view the map. (If Map 1 is the Active Map) • To edit the standby map, press on EDIT/VIEW MAP 2 to view the map.
Total Access 850 System Manual 5. Section 4 User Interface Guide APPENDICES (T1 ATM APPLICATIONS) The following example is for configuring T1 units with ATM firmware. However, all units using ATM firmware (SDSL, ADSL, SHDSL) may be configured in the same manner. To configure ATM Voice applications with other network types, disregard the T1 Interface Setup Instructions and configure your network interface as needed. Appendix A.
Section 4 User Interface Guide Total Access 850 System Manual The following example provides step by step instructions for configuring the Total Access 850 T1 ATM system (INTERFACES and L2 PROTOCOL) for a standard voice application. System Info and System Config parameters should be set according to your system need. Refer to System Info on page 73 and System Config on page 75 for more details. 1.
Total Access 850 System Manual Section 4 User Interface Guide FXS Interface Setup Instructions Step Action 1 From the main menu, select INTERFACES. 2 Highlight the CONFIG menu for the FXS interface and press . 3 Right arrow to select MODE and choose LOOP START, GROUND START, TANDEM (E&M), TR08 SINGLE, TR08 UVG, or DPO. This mode should be set based on the network configuration and the operation of each FXS port. All FXS ports are independent and do not need to have the same mode.
Section 4 User Interface Guide Total Access 850 System Manual FXS Interface Setup Instructions (Continued) 11 Press on the TANDEM [+] option to view the TANDEM options if the port mode is set to TANDEM (E&M). 12 Set the CONVERSION MODE of the port to either LOOP START or GROUND START. 13 Set the SUPERVISION of the port to either IMMEDIATE or WINK. Be sure to set the TANDEM options for each port set to TANDEM E&M. 2.
Total Access 850 System Manual Section 4 User Interface Guide Layer 2 Protocol Configuration – T1 Interface (Continued) 8 Select SETUP, and from the SETUP menu, enter the Gateway type under CALL CONTROL and enter the VPI and VCI values for communicating with that Gateway. For this application, CALL CONTROL and virtual identifier (VPI and VCI) values should be set appropriately for your network.
Section 4 User Interface Guide Total Access 850 System Manual Appendix B. RFC1483 Quick Start (IP Routing) The Total Access 850 allows for complete integration of voice and data delivery from one compact platform (see Figure 10). Once you have completed the voice turn up procedure from the previous example, adding data to the circuit requires some additional setup.
Total Access 850 System Manual Section 4 User Interface Guide T1 Interface Setup Instructions Step Action 1 From the main menu, select INTERFACES. 2 Highlight the CONFIG menu for the T1 interface and press . 3 Right arrow to select FORMAT and choose ESF or SF. This format must match the format used by the other units in the network. 4 Set the LINE CODE to B8ZS or AMI. This line code must match the line code used by the other units in the network.
Section 4 User Interface Guide .2. Total Access 850 System Manual Configuring the Layer 2 Protocol For more details on the configuration parameters discussed in this section, refer to the following pages: Layer 2 ATM Network Interface Protocol menus beginning on page 129 Layer 2 Protocol (ATM) Configuration – T1 Interface Step 206 Action 1 From the main menu, select L2 PROTOCOL and press . 2 Use the arrow keys to select the PROTOCOL field for the T1 interface. Press .
Total Access 850 System Manual Section 4 User Interface Guide 3. Setting the Router Options For more details on the configuration parameters discussed in this section, refer to the following pages: Router Ethernet Interface Configuration menus beginning on page 148 Router Network Interface Configuration menus beginning on page 148 Router Default Gateway menus beginning on page 157 Router Options – Ethernet Interface Step Action 1 From the main menu, select ROUTER and press .
Section 4 User Interface Guide Total Access 850 System Manual Router Options – T1 Interface (L2 Protocol = ATM) (Continued) 3 Select INTERFACES and press . Use the right arrow key to highlight the SETUP field for the T1 interface and press . Each virtual circuit on the T1 interface defined in the PVC CONFIG has a separate listing in the ROUTER INTERFACES table. 4 Set ACTIVE to YES to activate the virtual circuit. 5 Enter the appropriate VPI and VCI values.
Total Access 850 System Manual Section 4 User Interface Guide Appendix C. RFC1483 Quick Start (IP Routing with NAT) To illustrate the use of NAT, consider the example from Appendix B. RFC1483 Quick Start (IP Routing) on page 204. To add NAT to the IP routing example, use the NAT menus.
Section 4 User Interface Guide Total Access 850 System Manual Appendix D. RFC 1483 Quick Start (Bridging) Initial Setup It is best to configure Total Access 850 ATM applications by following the order of the top-level menus. For example, first configure the system parameters using the SYSTEM INFO and SYSTEM CONFIG menus. Next, configure the Layer 1 parameters using the INTERFACES menu. Once the Layer 1 information is configured, proceed to the Layer 2 setup using the L2 PROTOCOL menus.
Total Access 850 System Manual Section 4 User Interface Guide Ethernet Interface Setup Instructions Most applications should not require a manual setup for the Ethernet interface. By default, the Ethernet interface is configured to auto-detect the data rate (as either 10 or 100 Mbps). The following steps disable the auto-negotiation parameter and manually configure the interface. Step .2. Action 1 From the main menu, select INTERFACES.
Section 4 User Interface Guide Total Access 850 System Manual Layer 2 Protocol (ATM) Configuration – T1 Interface (Continued) 9 Set mode to ROUTE IP. Using this menu you also have the option to route only IP packets and bridge all other data packets (ROUTE IP/BRIDGE OTHER) or bridge all data packets on this connection (BRIDGE ALL). Refer to L2 Protocol (T1 ATM–T1–ATM) > Config > PVC Config > Setup (V35) on page 133 for more details. 10 Left arrow back to the main menu to save the changes. 3.
DETAIL LEVEL PROCEDURES DLP-1 Connecting a VT100 Terminal or PC to the CRAFT Port. . . . . . . . . . . . . . . . . . . . . . . . . . . 215 DLP-2 Logging in to the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217 DLP-3 Setting IP Parameters for the Total Access 850 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 DLP-4 Verifying Communications Over an IP LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 5 Detail Level Procedures 214 Total Access 850 System Manual © 2004 ADTRAN, Inc.
DLP-1 Connecting a VT100 Terminal or PC to the CRAFT Port Introduction Total Access 850 shelf management and provisioning are facilitated by a series of intuitive menus that are accessible on a computer screen. Connecting either a VT100 terminal or a PC emulating a VT100 terminal to the RJ-45 CRAFT port on the rear of the unit or the DB-9 CRAFT interface on the RCU faceplate allows access to the menus and management features of Total Access 850.
Section 5 DLP-1 Total Access 850 System Manual Perform the steps below in the order listed. 1. Connecting a VT100 terminal to Total Access 850: • Set the parameters of the VT100 terminal or PC to: – 9600 baud rate – 8 data bits – No parity – 1 stop bit – No flow control • If the terminal has a parallel setting, disable it and use the serial port. Using the RCU CRAFT Port • Plug the DB-9 male end of the data cable into the Total Access 850 CRAFT port on the front of the RCU.
DLP-2 Logging in to the System Introduction Once connected to the Total Access 850, you must login to the system to gain access to the management and provisioning functions. This DLP assumes you are connected to the Total Access 850 and provides specific steps for logging into the system. Prerequisite Procedures Complete DLP-1, Connecting a VT100 Terminal or PC to the CRAFT Port. To prevent electrical shock, do not install equipment in a wet location or during a lightning storm.
Section 5 DLP-2 Total Access 850 System Manual Perform the steps below in the order listed. 1. After connecting to the system, press any key to display the Login screen shown here. The blinking cursor at the Login field indicates that a password must be entered. 2. Enter the password for the Total Access 850 at the Login field. There is no manufacturer’s default password; press to enter the Total Access 850 menus. 3.
DLP-3 Setting IP Parameters for the Total Access 850 Introduction The Total Access 850 comes pre-programmed for default Telnet access. The following IP parameters apply: • IP Address: 10.0.0.1 • Subnet Mask: 255.255.255.0 • User: guest • Password: password For security purposes, change the default Telnet password during the initial unit configuration. (Refer to System Config > Management > Telnet Access > User List on page 77 for more details.
Section 5 DLP-3 Total Access 850 System Manual Perform the steps below in the order listed. 1. Connect the Total Access 850 unit to your VT100 system (details found in DLP-1, Connecting a VT100 Terminal or PC to the CRAFT Port). 2. Log in to the system. 3. From the ROUTER/CONFIG menu, select the INTERFACES option and press . 4. Select SETUP for the ETH interface, then PRIMARY IP. 5. Highlight the IP ADDRESS field and press .
DLP-4 Verifying Communications Over an IP LAN Introduction When the Ethernet port is connected to a local area network (LAN), test steps must be performed on the Total Access 850 to ensure that the unit is communicating properly over the network. This procedure outlines those steps. Prerequisite Procedures Before beginning this procedure, the unit should be physically connected to the LAN and the provisioning tasks detailed in DLP-3, Setting IP Parameters for the Total Access 850, should be complete.
Section 5 DLP-4 Total Access 850 System Manual Perform the steps below in the order listed. 1. Verify the Total Access 850 IP address. If you do not already have the IP Address for the Total Access 850, obtain it from the network administrator or manually check for the address in the ROUTER CONFIG/INTERFACE/SETUP/PRIMARY IP/IP ADDRESS menu of the Network Management interface. You must log in with a security level of 2 to modify the IP parameters on the Total Access 850.
Total Access 850 System Manual Section 5 DLP-4 From the same computer used in the previous step, Telnet to the Total Access 850 and verify that the Telnet session is properly opened (see DLP-5, Connecting to the Total Access 850 Using Telnet). Once the Telnet session is established, press to logout and close the session. Refer to the documentation of the computer system if you are unsure how to perform a Telnet.
Section 5 DLP-4 224 Total Access 850 System Manual © 2004 ADTRAN, Inc.
DLP-5 Connecting to the Total Access 850 Using Telnet Introduction The Total Access 850 comes pre-programmed for default Telnet access. The following IP parameters apply: • IP Address: 10.0.0.1 • Subnet Mask: 255.255.255.0 • User: guest • Password: password For security purposes, change the default Telnet password during the initial unit configuration. (Refer to System Config > Management > Telnet Access > User List on page 77 for more details.
Section 5 DLP-5 Total Access 850 System Manual Perform the steps below in the order listed. 1. Connect the computer to the Total Access 850 RCU faceplate CRAFT or rear CRAFT port (details in DLP-1, Connecting a VT100 Terminal or PC to the CRAFT Port). 2. Log in to the unit. 3. Select the SYSTEM CONFIG/MANAGEMENT/TELNET ACCESS menu and set the TELNET ACCESS to ON. 4. Under the SYSTEM CONFIG/MANAGEMENT/TELNET ACCESS menu, select the TELNET USER LIST; press . The following screen appears. 5.
Total Access 850 System Manual Section 5 DLP-5 12. From a remote computer system connected to the LAN, Telnet to the Total Access 850. Refer to the documentation of the computer system if you are unsure how to perform a Telnet. Most computers running a networked version of Microsoft Windows™ or UNIX allow a Telnet to be performed by simply typing “Telnet ” at a command line prompt.
Section 5 DLP-5 Total Access 850 System Manual 14. Enter the password assigned in step 6. After entering the correct password, the Total Access 850 main menu is displayed (see below): 15. After completing your configuration changes they are automatically saved (or manually save them by pressing ), press to log off the menus, and close the Telnet window. 228 © 2004 ADTRAN, Inc.
DLP-6 Adding/Removing Users and Changing Password Security Levels Introduction Password security levels only apply to users connecting to the Total Access 850 system through Telnet access. All connections made through the CRAFT interface ALWAYS have maximum security rights. All menu items in the Total Access 850 are protected by passwords of varying security levels.
Section 5 DLP-6 Total Access 850 System Manual Perform the steps below in the order listed. 1. Connect to the Total Access 850 using either the 10BASET, rear CRAFT, or RCU faceplate CRAFT interfaces. If you are not already connected to the unit’s RCU faceplate CRAFT or rear CRAFT interface (either with a VT100 compatible terminal or with a PC running VT100 emulation software), follow the procedure in DLP-1, Connecting a VT100 Terminal or PC to the CRAFT Port).
Total Access 850 System Manual Section 5 DLP-6 8. Determine the password level for the corresponding label. The Total Access 850 contains seven different password levels. The following chart gives a brief description of each level. Select Level... If you want the user to....
Section 5 DLP-6 232 Total Access 850 System Manual © 2004 ADTRAN, Inc.
DLP-7 Updating the Firmware using TFTP Introduction The Total Access 850 supports firmware updates using TFTP or XMODEM. (Use the 10/100BASET Ethernet port and TFTP from a network server, or use XMODEM and the RCU faceplate CRAFT or rear CRAFT interfaces.) This DLP provides the steps for a successful firmware upgrade using the 10/100BASET Ethernet port and a TFTP server. (See DLP-8, Updating the Firmware using XMODEM, for instructions on using XMODEM.
Section 5 DLP-7 Total Access 850 System Manual Perform the steps below in the order listed. 1. Connect to the Total Access 850 using the 10/100BASET interface. If you are not already connected to the unit’s ETHERNET port using Telnet client software, use the procedure in DLP-5, Connecting to the Total Access 850 Using Telnet, to connect to the unit. 2. Log in to the unit using the read-write password (see DLP-2, Logging in to the System for details). 3. Verify the TFTP server is running on the network.
Total Access 850 System Manual Section 5 DLP-7 9. Select START TRANSFER to start the update. Enter Y to confirm the upgrade. Prior to the start of the upgrade, the transfer status will display IDLE. During the TFTP upload process, various status messages display in CURRENT UPDATE STATUS to indicate progress. The following table describes these messages. Message Meaning Indicates communication with the TFTP network server has been Transferring...
Section 5 DLP-7 236 Total Access 850 System Manual © 2004 ADTRAN, Inc.
DLP-8 Updating the Firmware using XMODEM Introduction The Total Access 850 supports firmware updates using TFTP or XMODEM. (Use the 10/100BASET Ethernet port and TFTP from a network server, or use XMODEM and the rear CRAFT or RCU faceplate CRAFT interface.) This procedure outlines the steps for a successful firmware upgrade using the rear CRAFT or RCU faceplate CRAFT interface and XMODEM software. (See DLP-7, Updating the Firmware using TFTP, for instructions on using TFTP.
Section 5 DLP-8 Total Access 850 System Manual Updating Firmware via the Console Menus Perform the steps below in the order listed. 1. Connect to the Total Access 850 using the RCU faceplate CRAFT (DB-9) or rear CRAFT (RJ-45) interface. Selecting a higher baud rate connection makes the file transfer process faster. Verify that the baud rate setting on the Total Access 850 matches the VT100 emulation software COM port settings.
DLP-9 Saving the Current Configuration Using TFTP Introduction The Total Access 850 supports configuration transfers from the unit (via the 10/100BASET Ethernet port) to a TFTP server located on the network. This DLP provides the steps to follow for a successful configuration transfer using the 10/100BASET Ethernet port and a TFTP Server.
Section 5 DLP-9 Total Access 850 System Manual Perform the steps below in the order listed. 1. Connect to the Total Access 850 using the 10/100BASET interface. If you are not already connected to the unit’s 10/100BASET port using Telnet client software, use the procedure in DLP-5, Connecting to the Total Access 850 Using Telnet, to connect to the unit. 2. Log in to the unit using the read-write password (see DLP-2, Logging in to the System, for details). 3.
DLP-10 Loading a Configuration Using TFTP Introduction The Total Access 850 supports configuration uploads from a unit (via the 10/100BASET Ethernet port) to a TFTP server located on the network. This DLP provides the steps to follow for a successful configuration upload using the 10/100BASET Ethernet port and a TFTP Server.
Section 5 DLP-10 Total Access 850 System Manual Perform the steps below in the order listed. 1. Connect to the Total Access 850 using the 10/100BASET interface. If you are not already connected to the unit’s 10/100BASET port using Telnet client software, use the procedure in DLP-5, Connecting to the Total Access 850 Using Telnet, to connect to the unit. 2. Log in to the unit using the read-write password (see DLP-2, Logging in to the System, for details). 3.
Total Access 850 System Manual Section 5 DLP-10 10. When the upload process has successfully completed, IDLE displays in the CURRENT TRANSFER STATUS field and DOWNLOAD COMPLETE displays in the PREVIOUS TRANSFER STATUS field. 11. After an appropriate length of time, the user may Telnet back into the unit. 64203376L1-1B © 2004 ADTRAN, Inc.
Section 5 DLP-10 244 Total Access 850 System Manual © 2004 ADTRAN, Inc.
DLP-11 Saving and Transferring a Current Configuration Using XMODEM Introduction The Total Access 850 supports configuration transfers from the unit via the rear CRAFT or RCU faceplate CRAFT interfaces using a VT100 terminal or terminal emulator (with XMODEM). This DLP provides the steps for a successful configuration transfer using either the rear CRAFT or RCU faceplate CRAFT port and XMODEM.
Section 5 DLP-11 Total Access 850 System Manual Perform the following steps in the order listed. 1. Connect to the Total Access 850 using the rear CRAFT (RJ-45) port on the back of the Total Access 850 or the RCU faceplate CRAFT (DB-9) interface. If you are not already connected to the unit’s rear CRAFT or RCU faceplate CRAFT interface, either with a VT100 compatible terminal or with a PC running VT100 emulation software, follow the procedure in DLP-1, Connecting a VT100 Terminal or PC to the CRAFT Port.
DLP-12 Loading a Configuration Using XMODEM Introduction The Total Access 850 supports configuration uploads from a unit via the rear CRAFT or RCU faceplate CRAFT interface using a VT100 terminal or terminal emulator (with XMODEM). This DLP provides the steps for a successful configuration upload using either the rear CRAFT or RCU faceplate CRAFT port and XMODEM protocol.
Section 5 DLP-12 Total Access 850 System Manual Perform the following steps in the order listed. 1. Connect to the Total Access 850 using the rear CRAFT (RJ-45) or the RCU faceplate CRAFT (DB-9) interface located on the front of the RCU. If you are not already connected to the unit’s rear CRAFT or RCU faceplate CRAFT interface, either with a VT100 compatible terminal or with a PC running VT100 emulation software, follow the procedure in DLP-1, Connecting a VT100 Terminal or PC to the CRAFT Port.
DLP-13 Saving and Loading Text Configuration using Terminal Command Line Introduction The Total Access 850 RCU has the ability to download a text file which contains the configuration of the entire unit. This configuration may then be altered in a text editor and uploaded to any Total Access 850 RCU. This DLP will explain how to save and load the text configuration file for the ADTRAN Total Access 850.
Section 5 DLP-13 Total Access 850 System Manual Perform the steps below in the order listed. Saving the router's configuration 1. Establish a connection to the router with the VT100 terminal software either through the rear CRAFT or RCU faceplate CRAFT port. 2. From the main menu, select SYSTEM UTILITY, then TERMINAL MODE; press . 3. The following screen appears. 4. At the terminal prompt, type DOWNLOAD; press . The following screen appears.
Total Access 850 System Manual Section 5 DLP-13 5. Enable "capture" or "logging" in the terminal software, saving it to a file on your computer. 6. Press the SPACE BAR to continue. The router will then print its configuration to the terminal screen. (With capture enabled, the terminal software will capture the configuration and write it to the designated file.) 7. When the configuration stops printing, end the capture. The router's configuration is now saved to the designated file. 8.
Section 5 DLP-13 252 Total Access 850 System Manual © 2004 ADTRAN, Inc.
DLP-14 A.03 to A.04 Firmware Upgrade Introduction The Total Access line of Integrated Access Devices includes both the ATM and TDM versions of the Total Access 850. Until now, the Total Access TDM units have been running firmware version A.03.xx. Recently, A.04.xx has been released to support the TDM Total Access IADs. The development of A.04.xx code is a significant step in the evolution of the Total Access product line, as it allows all Total Access family members to share the same base code.
Section 5 DLP-14 Total Access 850 System Manual Tools and Materials Required • • • VT100 compatible terminal or computer with terminal emulation software Appropriate cable to connect terminal to the unit (customer-provided) DB-9 male to DB-9 female cable (customer provided) for connecting to the CRAFT port on the front of the RCU DB-9 female to RJ-45 female adapter (customer provided) for connecting to the CRAFT port on the rear of the unit • Perform the steps below in the order listed.
Total Access 850 System Manual Section 5 DLP-14 4. Reconfigure the unit for the specific application. Upgrading from A.03 to A.04 directly (or from A.04 to A.03 directly) will erase the unit's configuration. 64203376L1-1B © 2004 ADTRAN, Inc.
Section 5 DLP-14 256 Total Access 850 System Manual © 2004 ADTRAN, Inc.
DLP-15 Using the ADTRAN Utility Syslog Introduction The Total Access 850 Syslog Utility records various message types at settable threshold levels to an external Syslog server (software supplied with the Total Access 850 system ADTRAN Utilities). Prerequisite Procedures This procedure assumes that the Total Access 850 unit is connected to an IP network and is powered up.
Section 5 DLP-15 Total Access 850 System Manual Setting up the Total Access 850 to use Syslog: 1. Log in to the system with maximum rights (see DLP-2, Logging in to the System). Once you have logged into the Total Access 850, go to SYSTEM CONFIG/SYSLOG.
Total Access 850 System Manual Section 5 DLP-15 . Additional Syslog Features: • The MONITOR feature allows all Syslog messages to be prefiltered by SYSTEM NAME, SOURCE, SLOT, and PORT before displaying these messages to the user and logging the message to the pre-designated monitor log file. Various filter options may be defined by selecting SOURCE. The figure below shows the SOURCE FILTER window. When the MONITOR button is selected, the file will be logged to LOCAL8.TXT.
Section 5 DLP-15 Total Access 850 System Manual • Under the LOG FILES menu option, the user may erase log files, define Red events, set priorities, and clear Red events. The ERASE LOG FILES option erases the specified text log file. • DEFINE RED EVENTS allows the user to predefine a message priority condition so that if the condition occurs, the file is highlighted in red.
DLP-16 Connecting the Alarm Contacts and the External Input Introduction Alarm connections alert the user when a selected alarm condition exists. Pressing the Alarm Cut-Off (ACO) switch on the front panel of the Total Access 850 PSU clears the alarm. This procedure details the steps which must be performed to use the Total Access 850 alarm connections and the ACO switch. This procedure should be performed at installation on each Total Access 850 shelf that is wired out to external office alarm equipment.
Section 5 DLP-16 Total Access 850 System Manual Perform the steps below in the order listed. 1. Backplane alarm connections (P5) are labeled as shown in the table below and illustrated in the figure.
Total Access 850 System Manual Section 5 DLP-16 P5 P7 P6 2. Alarm relay contacts are open during normal operation. The alarm relay contacts close in the event of a local alarm condition or the receipt of an alarm from the T1 Carrier. 3. In a carrier alarm condition such as a Red, Yellow, or Blue (unframed all 1s), various alarm contacts in the PSU close. 4. Carrier alarm conditions cause the Total Access 850 to initiate trunk processing.
Section 5 DLP-16 264 Total Access 850 System Manual © 2004 ADTRAN, Inc.
DLP-17 Configuring the Total Access 850 for Dual T1 Maps Introduction The Total Access 850 with firmware A.04.02 or higher has a DUAL T1 MAP feature that allows two network T1 connections for the termination of data and voice applications. The primary network T1 MAP can be configured for internal router usage (FT1/24 DS0s maximum) and to any access module installed. The DSX MAP can be used for FXS/FXO modules in slots 1-6 only.
Section 5 DLP-17 Total Access 850 System Manual Perform the steps below in the order listed. 1. Connect the Total Access 850 unit to your VT100 system (details found in DLP-1, Connecting a VT100 Terminal or PC to the CRAFT Port). 2. Log in to the system with maximum rights (details are in DLP-2, Logging in to the System). 3. From the DS0 MAPS menu, select the ACTIVE MAP option and press . 4. From the DS0 MAPS > ACTIVE MAPS menu, select the DUAL T1 MAP option; press .
Total Access 850 System Manual Section 5 DLP-17 5. Edit the Primary T1 Map by pressing on EDIT/VIEW T1 MAP [+].The following screen appears. Figure 2. Primary T1 Map The T1 Map can be mapped to the internal router or other available access module. 64203376L1-1B © 2004 ADTRAN, Inc.
Section 5 DLP-17 Total Access 850 System Manual 6. Edit the Secondary T1 Map (DSX Map) by pressing on EDIT/VIEW DSX MAP [+]. The following screen appears. Figure 3. DSX Map The DSX Map can be mapped to the FXS and FXO access modules only. 7. Left arrow back to DS0 MAPS and log off by pressing . 268 © 2004 ADTRAN, Inc.
ADTRAN UTILITIES This section provides instructions for configuring and using the ADTRAN Utilities software programs including Telnet, VT100, Syslog, and TFTP. ADTRAN delivers several PC software utilities with the Total Access 850. These utilities are located on the CD-ROM that came with your shipment. The utilities make it easier to interface with the terminal menu and transfer configuration files to and from TFTP servers. The utilities all run on Microsoft Windows 3.1 or higher.
Section 6 ADTRAN Utilities 1. Total Access 850 System Manual TELNET UTILITY Access the Telnet program remotely through the Ethernet port. For a detailed description of how to work within the terminal menu, refer to Navigating the Terminal Menu on page 67 (in the User Interface Guide section of this manual). The Telnet menus include SESSION, EDIT, OPTIONS, CAPTURE, and HELP (see the menu tree in Figure 1).
Total Access 850 System Manual Section 6 ADTRAN Utilities Session Menu Click on SESSION to open the Telnet session. Connect Opens dialog box for setting HOST NAME and PORT parameters for a Telnet session. Also lets you EDIT ENTRY, ADD NEW entry, and DELETE stored entries. When the parameters are set, click CONNECT to make the connection. Click CANCEL to end the session. Host Name Accepts and stores host names. You may enter either a name, an IP address, or a domain name directly from this field.
Section 6 ADTRAN Utilities Total Access 850 System Manual Disconnect Terminates the Telnet session. To re-establish the session, select CONNECT from SESSION MENU or press ENTER three times. This action restores the previous connection. Transfer Cfg This feature is used with ADTRAN products to send configuration files to the unit. Exit Ends the Telnet session and closes the Telnet screen. Edit Menu Provides COPY and PASTE commands. Options Menu Provides viewing alternatives for the terminal screen.
Total Access 850 System Manual Section 6 ADTRAN Utilities Help Menu Provides online help for using the ADTRAN Utilities. Contents Opens the online help. IP Status Displays the local port address and the status of the connection. About Displays version and owner information. 2. VT100 UTILITY Use the VT100 to configure an Total Access 850 which is directly connected to a PC. The VT100 display is almost identical to the Telnet display.
Section 6 ADTRAN Utilities Total Access 850 System Manual Session Menu Opens VT100 terminal emulation session. Connect Opens a specified serial port for a VT100 session. Disconnect Closes a specified serial port at the end of a VT100 session. File Transfer Uploads and downloads files to and from an Total Access 850. XMODEM CRC Selects the XMODEM file transfer protocol. ASCII Cfg Files Selects ASCII transfer mode. Primarily useful for configuration transfers for the ADTRAN products.
Total Access 850 System Manual Section 6 ADTRAN Utilities AutoRepeat Repeats characters you select from the keyboard, if you hold down the key. Capture Menu Identical to the Telnet CAPTURE MENU (see Capture Menu on page 272). Help Menu Provides online help and information about the version number. Contents Opens online help. About Displays version and owner information. 3.
Section 6 ADTRAN Utilities Total Access 850 System Manual Figure 4. TFTP Server Interface Only one configuration transfer session (upload or download) may be active at a time. The TCP/IP parameters are not saved or overwritten as part of an Total Access 850 unit’s transferred configuration to allow sending identical configurations to multiple units. When you start this program, a port is automatically opened. Server Menu Provides enable, disable, abort, and exit options. Enable Enables the TFTP server.
Total Access 850 System Manual Section 6 ADTRAN Utilities Help Provides online help and version information. Contents Opens online help. About Displays version and owner information. 4. STATUS FIELD This field displays general information about port and transfer status. This field is read-only. The unlabeled field in the center of the screen displays prompts about the status of active transfers, such as bytes transferred and received. 5.
Section 6 ADTRAN Utilities 278 Total Access 850 System Manual © 2004 ADTRAN, Inc.
MIBS This section is divided into two parts: (1) SNMP information for TDM units and (2) SNMP information for ATM units. Each section details the Management Information Bases (MIBs) supported, MIB Compilation Order, Traps Supported, and MIB Variables supported. CONTENTS MIBs Supported by TDM Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258 MIB Compilation Order For TDM Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 7 MIBs Total Access 850 System Manual For this section, TDM units refers to Total Access 850 units running A.04 firmware or later. ATM units refers to Total Access 850 units running C.02 firmware or previous. The TDM units support SNMP Version 2. The ATM units support SNMP Version 1. 1. MIBS SUPPORTED BY TDM UNITS Standard RFC MIBs: RFC1573.mi2 IANAifType-MIB RFC1907.mi2 SNMPv2-MIB RFC2011.mi2 IP-MIB RFC2096.mi2 IP-FORWARD-MIB RFC2115.mi2 FRAME-RELAY-DTE-MIB RFC2493.
Total Access 850 System Manual 2. Section 7 MIBs MIB COMPILATION ORDER FOR TDM UNITS IANAifType-MIB PerfHist-TC-MIB SNMPv2-MIB (if not included with SNMP manager) IF-MIB IP-MIB IP-FORWARD-MIB FRAME-RELAY-DTE-MIB DS1-MIB DS0-MIB DS0BUNDLE-MIB EtherLike-MIB CIRCUIT-IF-MIB ADTRAN-MIB ADTRAN-IADSYS-MIB ADTRAN-IADROUTER-MIB 3.
Section 7 MIBs (T1 WAN interface only): Total Access 850 System Manual adIadDs1CRC - 1003217 adIadDs1LCV - 1003218 adIadDs1SLP - 1003219 From ADTRAN-IADVOICE-MIB: adIadVoiceTestStatusActive - 1003401 adIadVoiceTestStatusClear - 1003402 adIadVoiceAlarmBitActive - 1003403 adIadVoiceAlarmBitInactive - 1003404 adIadVoiceGatewayDown - 1003405 adIadVoiceGatewayUp - 1003406 adIadVoiceaLifeLineActivated - 1003407 adIadVoiceaLifeLineDeactivated - 1003408 4.
Total Access 850 System Manual 6. Section 7 MIBs MIB COMPILATION ORDER FOR ATM UNITS RFC1213-MIB RFC1406-MIB RFC1695-MIB ADTRAN-MIB ADTRAN-ADTARTR-TRAP-MIB 7.
Section 7 MIBs Total Access 850 System Manual ifMtu RO ifSpeed RO ifPhysAddress RO ifOperStatus RO ifInOctets RO ifInUcastPkts RO ifInNUcastPkts RO ifInDiscards RO ifInErrors RO ifInUnknownProtos RO ifOutOctets RO ifOutUcastPkts RO ifOutNUcastPkts RO ifOutDiscards RO ifOutErrors RO ifSpecific RO ip: ipForwarding RO ipDefaultTTL RO ipInReceives RO ipInHdrErrors RO ipInAddrErrors RO ipForwDatagrams RO ipInUnknownProtos RO ipInDiscards RO ipInDelivers RO ipOu
Total Access 850 System Manual Section 7 MIBs ipAddrEntry ipAdEntAddr RO ipAdEntIfIndex RO ipAdEntNetMask RO ipAdEntBcastAddr RO ipAdEntReasmMaxSize RO ipRouteTable: ipRouteEntry ipRouteDest RO ipRouteIfIndex RO ipRouteMetric1 RO ipRouteMetric2 RO ipRouteMetric3 RO ipRouteMetric4 RO ipRouteNextHop RO ipRouteType RO ipRouteProto RO ipRouteAge RO ipRouteMask RO ipRouteMetric5 RO ipRouteMetricInfo RO ipNetToMediaTable: ipNetToMediaEntry ipNetToMediaIfIndex RO ipNetToMedi
Section 7 MIBs 286 Total Access 850 System Manual icmpInAddrMasks RO icmpInAddrMaskReps RO icmpOutMsgs RO icmpOutErrors RO icmpOutDestUnreachs RO icmpOutTimeExcds RO icmpOutParmProbs RO icmpOutSrcQuenchs RO icmpOutRedirects RO icmpOutEchos RO icmpOutEchoReps RO icmpOutTimestamps RO icmpOutTimestampReps RO icmpOutAddrMasks RO icmpOutAddrMaskReps RO © 2004 ADTRAN, Inc.
Total Access 850 System Manual Section 7 MIBs tcp: tcpRtoAlgorithm RO tcpRtoMin RO tcpRtoMax RO tcpMaxConns RO tcpActiveOpens RO tcpPassiveOpens RO tcpAttemptFails RO tcpEstabResets RO tcpCurrEstab RO tcpInSegs RO tcpOutSegs RO tcpRetransSegs RO tcpConnTable tcpConnEntry tcpConnState RO tcpConnLocalAddress RO tcpConnLocalPort RO tcpConnRemAddress RO tcpConnRemPort RO tcpInErrs RO tcpOutRsts RO udp: udpInDatagrams RO udpNoPorts RO udpInErrors RO udpOutDatagrams
Section 7 MIBs Total Access 850 System Manual egp: egpInMsgs RO egpInErrs RO egpOutMsgs RO egpOutErrors RO egpNeighState RO egpNeighAddr RO egpNeighAs RO egpNeighInMsgs RO egpNeighInErrs RO egpNeighOutMsgs RO egpNeighOutErrs RO egpNeighInErrMsgs RO egpNeighOutErrMsgs RO egpNeighStateUps RO egpNeighStateDowns RO egpNeighIntervalHello RO egpNeighIntervalPoll RO egpNeighMode RO dsx1: dsx1ConfigTable dsx1ConfigEntry 288 dsx1LineIndex RO dsx1IfIndex RO dsx1TimeElapsed
Total Access 850 System Manual Section 7 MIBs dsx1CurrentTable dsx1CurrentEntry dsx1CurrentIndex RO dsx1CurrentESs RO dsx1CurrentSESs RO dsx1CurrentSEFs RO dsx1CurrentUASs RO dsx1CurrentCSSs RO dsx1CurrentPCVs RO dsx1CurrentLESs RO dsx1CurrentBESs RO dsx1CurrentLCVs RO dsx1IntervalTable dsx1IntervalEntry dsx1IntervalIndex RO dsx1IntervalNumber RO dsx1IntervalESs RO dsx1IntervalSESs RO dsx1IntervalSEFs RO dsx1IntervalUASs RO dsx1IntervalCSSs RO dsx1IntervalPCVs RO dsx1In
Section 7 MIBs Total Access 850 System Manual dsx1FracTable dsx1FracEntry dsx1FracIndex RO dsx1FracNumber RO dsx1FractIfIndex RO snmp: 290 snmpInPkts RO snmpOutPkts RO snmpInBadVersions RO snmpInBadCommunityNames RO snmpInBadCommunityUses RO snmpInASNParseErrs RO snmpInTooBigs RO snmpInNoSuchNames RO snmpInBadValues RO snmpInReadOnlys RO snmpInGenErrs RO snmpInTotalReqVars RO snmpInTotalSetVars RO snmpInGetRequests RO snmpInSetRequests RO snmpInGetRequests RO snmpIn
Total Access 850 System Manual Section 7 MIBs atm: atmInterfaceTable atmInterfaceEntry atmInterfaceMaxVpcs RO atmInterfaceMaxVccs RO atmInterfaceConfVpcs RO atmInterfaceConfVccs RO atmInterfaceMaxActiveVpiBits RO atmInterfaceMaxActiveVciBits RO atmInterfaceIlmiVpi RO atmInterfaceIlmiVci RO atmInterfaceAddressType RO atmInterfaceAdminAddress RO atmInterfaceMyNeighborIpAddress RO atmInterfaceMyNeigherIfName RO atmInterfaceTCTable atmInterfaceTCEntry atmInterfaceOCDEvents RO atmInte
Section 7 MIBs Total Access 850 System Manual atmVclLastChange RO atmVclReceiveTrafficDescrIndex RO atmVclTransmitTrafficDescrIndex RO atmVccAalType RO atmVccAal5CpcsTransmitSduSize RO atmVccAal5CpcsReceiveSduSize RO atmVccAal5EncapsType RO atmVclCrossConnectIdentifier RO atmVclRowStatus RO aal5VccVpi RO aal5VccVci RO aal5VccCrcErrors RO aal5VccSarTimeOuts RO aal5VccOverSizedSDUs RO aal5VccTable aal5VccEntry 292 © 2004 ADTRAN, Inc.
