ATLAS 800PLUS User Manual Part Number 1200226L1 Part Number 1200228L1 61200226L1-1C May 2000
TRADEMARKS Windows is a registered trademark of Microsoft Corporation. DMS 100 is a registered trademark of Northern Telecom. 5ESS is a registered trademark of AT&T. AT&T is a registered trademark. 901 Explorer Boulevard P.O. Box 140000 Huntsville, AL 35814-4000 (256) 963-8000 © 2000 ADTRAN, Inc. All Rights Reserved. Printed in U.S.A.
FCC regulations require that in this manual the following information be provided to the customer: 1. 2. 3. 4. 5. 6. 7. This equipment complies with Part 68 of the FCC rules. The required label is affixed to the bottom of the chassis. An FCC-compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68-compliant.
Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Affidavit Requirements for Connection to Digital Services • An affidavit is required to be given to the telephone company whenever digital terminal equipment without encoded analog content and billing protection is used to transmit digital signals containing encoded analog content which are intended for eventual conversion into voiceband analog signals and transmitted on the network.
Affidavit for Connection of Customer Premises Equipment to 1.
I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate compliance with the information as provided in the preceding paragraph, if so requested.
Canadian Equipment Limitations The Industry Canada Certification label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
LIMITED PRODUCT WARRANTY ADTRAN warrants that for five (5) years from the date of shipment to Customer, all products manufactured by ADTRAN will be free from defects in materials and workmanship. ADTRAN also warrants that products will conform to the applicable specifications and drawings for such products, as contained in the Product Manual or in ADTRAN's internal specifications and drawings for such products (which may or may not be reflected in the Product Manual).
About this Manual The ATLAS 800PLUS system consists of the Base Unit and one or more option modules. (Each option module includes its own user manual which contains specific information about installing, configuring, and testing the option module; insert the option module manuals into this binder.
Notes provide additional useful information. Cautions signify information that could prevent service interruptions. Warnings provide information that could prevent damage to the equipment or endangerment to human life.
xii
Table of Contents List of Figures....................................................................................................................... xxiii List of Tables .......................................................................................................................... xxv Chapter 1 Introducing the ATLAS 800PLUS ........................................................................................ 1-1 Product Overview..............................................................
Table of Contents Submenus ............................................................................................................................................... 4-7 Sub-submenus ................................................................................................................................ 4-7 Status.............................................................................................................................................................. 4-7 S0 System ...........
Table of Contents Serial Number ........................................................................................................................................6-3 Boot ROM Rev ........................................................................................................................................6-3 System Status ................................................................................................................................................. 6-3 Event Log ............
Table of Contents TXINIT Timer ............................................................................................................................... 6-12 TXFA Timer .................................................................................................................................. 6-12 TXADD01 Timer .......................................................................................................................... 6-12 TXDEQ Timer ..............................................
Table of Contents Test ...........................................................................................................................................................7-2 State ..........................................................................................................................................................7-2 Status .......................................................................................................................................................
Table of Contents Source ID ................................................................................................................................................ 9-3 Outdial Number .................................................................................................................................... 9-3 Force Mode ............................................................................................................................................ 9-3 Backup Criteria ..........
Table of Contents Global Param ............................................................................................................................................... 10-8 End of Number Timeout .....................................................................................................................10-8 Area Code .............................................................................................................................................10-8 Nbr Complete Templates ........
Table of Contents Dial Call As ................................................................................................................................. 10-18 Source ID ..................................................................................................................................... 10-18 Min DS0s ..................................................................................................................................... 10-18 Max DS0s ....................................
Table of Contents Clear Red Events ..................................................................................................................................13-4 Help............................................................................................................................................................... 13-4 Telnet Utility ................................................................................................................................................
Table of Contents Disable ................................................................................................................................................ 13-11 Abort ................................................................................................................................................... 13-11 Exit ....................................................................................................................................................... 13-11 Print Log .
List of Figures Figure 1-1. Point-to-Point Circuit.............................................................................................................. 1-2 Figure 1-2. Frame Relay Circuit ................................................................................................................ 1-3 Figure 1-3. Digital Access Cross-Connect System (DACS) ................................................................... 1-4 Figure 1-4. T1 Bandwidth Management ...................................
List of Figures Figure 13-2. SysLog Menu Tree for the Menu Bar.................................................................................. 13-3 Figure 13-3. Telnet Menu Tree................................................................................................................... 13-5 Figure 13-4. VT-100 Menu Tree ................................................................................................................. 13-8 Figure 13-5. TFTP Server Interface Menu Tree .................
List of Tables Table 2-1. Table 2-2. Table 2-3. Table 2-4. Table 4-1. Table 4-2. Table 4-3. Table 6-1. Table 6-2. Table 8-1. Table 10-1. Table 10-2. Table 10-3. Table 11-1. Table 12-1. Table 12-2. Table 12-3. Table 12-4. Table 12-5. Table A-1. Table A-2. Table A-3. Table A-4. Table A-5. Table A-6. Table A-7. Table A-8. Table A-9. Table A-10. Table A-11. Control/Chain In Pinout........................................................................................................
List of Tables xxvi ATLAS 800PLUS User Manual 61200226L1-1
Chapter 1 Introducing the ATLAS 800PLUS PRODUCT OVERVIEW The ATLAS 800PLUS is a modular, highly scalable platform that provides robust solutions for the wide area communication needs of medium-to-large corporations and network access providers. ATLAS is an Integrated Access System with the most extensive support of dedicated bandwidth management and access switching in the industry. The ATLAS 800PLUS is a high performance version of the ATLAS 800.
Chapter 1. Introducing the ATLAS 800PLUS The modules include the following: • Quad Nx 56/64 Module • Quad T1/PRI Module • Octal Basic Rate ISDN Module • T3 Module • Async-232 Module • Modem-16 Module Frame Relay Frame relay is a packet-switched service that allows efficient transfer of bursty traffic in a WAN environment. It offers lower-cost data transfer when compared to typical point-to-point applications.
Chapter 1. Introducing the ATLAS 800PLUS Frac T1 Frame Relay Figure 1-2. Frame Relay Circuit The Frame Relay/Router upgrade option adds the capability for the ATLAS series of Integrated Access Devices to act as a voice/data FRAD, a frame relay switch, and an IP router in addition to the current available bandwidth manager and switch applications.
Chapter 1. Introducing the ATLAS 800PLUS fered, providing detailed system configuration through an easy-to-use menu system. The terminal interface is secured by six levels of password protection with varying degrees of management privileges. The terminal interface is accessed locally or remotely using either the EIA-232 Chain In port on the rear of the unit or the Telnet interface. The 10BaseT interface on the Base Unit provides an Ethernet connection for SNMP and Telnet connections.
Chapter 1. Introducing the ATLAS 800PLUS plications including T1 “drop and insert,” channel grooming, and wide area data transport. ATLAS is ideal for point-to-point configurations or access to public networks. For optimization of existing equipment and network resources, ATLAS can be paired with ADTRAN’s TSU product offerings to support a variety of data and analog voice applications (see Figure 1-4). Figure 1-4.
Chapter 1. Introducing the ATLAS 800PLUS Figure 1-5.
Chapter 1. Introducing the ATLAS 800PLUS Dedicated Connection Maps • Up to five connection maps • Time of day/day of week configurable • Preserves signaling through cross-connect • No effect on non-configured channels Switched Connection Maps • Inbound and outbound call filtering and blocking Testing • Local and remote: payload/line, V.
Chapter 1.
Chapter 2 Installing the ATLAS 800PLUS INSPECT THE ADTRAN SHIPMENT Before installing the ATLAS 800PLUS, carefully inspect the ATLAS 800PLUS Base Unit for shipping damage. If you suspect damage, file a claim immediately with the carrier and then contact ADTRAN Technical Support (see Warranty and Technical Support Information on page C-1). If possible, keep the original shipping container for returning the ATLAS 800PLUS for repair or for verification of damage during shipment.
Chapter 2. Installing the ATLAS 800PLUS AC Powered Unit The AC powered ATLAS 800PLUS (P/N 1200226L1) comes equipped with a detachable 8-foot power cord with a three-prong plug for connecting to a grounded power receptacle. Power to the ATLAS 800PLUS must be from a grounded 115 VAC, 60 Hz or 220 VAC, 50-60 Hz source. DC Powered Unit The DC powered ATLAS 800 PLUS (P/N 1200228L1) comes equipped with a terminal block on the rear of the unit.
Chapter 2. Installing the ATLAS 800PLUS The supplementary equipment grounding conductor shall not be smaller in size than the ungrounded branch-circuit supply conductors. The supplementary equipment grounding conductor shall be connected to the product at the terminal provided, and shall be connected to ground in a manner that will retain the ground connection when the product is unplugged from the receptacle.
Chapter 2. Installing the ATLAS 800PLUS Control/Chain Out NTWK1 Connects to Chain In of another unit RJ-48C Connection Port Control/ Chain In Interface of Chain In 10 Base T MON (Monitor) NTWK2 RJ-48C Connection Port Bantam test jack RJ-48C Connection Port Power Switch CAUTION: MAINTENANCE TO BE PERFORMED BY TRAINED SERVICE PERSONNEL ONLY CAUTION: FOR CONTINUTED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE AND RATING OF FUSE.
Chapter 2. Installing the ATLAS 800PLUS Table 2-1. Control/Chain In Pinout PIN NAME DESCRIPTION 1 GND Ground - connected to unit chassis 2 RTS Request to send - flow control 3 RXDATA Data received by the ATLAS 800PLUS 4 DTR Data terminal ready 5 TXDATA Date transmitted by the ATLAS 800PLUS 6 CD Carrier detect 7 UNUSED — 8 CTS Clear to send - flow control Control/Chain Out Port The Control/Chain Out port (RJ-48C) connects to another ATLAS 800PLUS Chain In connector.
Chapter 2. Installing the ATLAS 800PLUS Table 2-2. Control/Chain Out Pinout (Continued) PIN NAME 5 RX DATA 6,7,8 DESCRIPTION Data received from chained units by the ATLAS. Connect to TX DATA of the next unit (Chain In pin 5). UNUSED — Network Connection The two eight-pin modular jacks labeled NTWK 1 and NTWK 2 provide the network connection. The two Network Interface (NI) ports comply with the applicable ANSI and AT&T® standards.
Chapter 2. Installing the ATLAS 800PLUS Ethernet 10BaseT Connection The 10BaseT Ethernet port (RJ-48C) provides an Ethernet LAN connection, which is used for TFTP, SNMP, and Telnet connection. Connection The network connection follows, with the pinout shown in Table 2-4. Connector type (USOC) RJ-48C Part number AMP# 555164-2 Table 2-4.
SLOT 1 SLOT 5 SLOT 2 SLOT 6 SLOT 3 SLOT 7 SLOT 4 SLOT 8 POWER SUPPLY Chapter 2. Installing the ATLAS 800PLUS Figure 2-3. ATLAS 800PLUS Slot Designation (Rear View) INSTALL ANY OPTION MODULES After installing the base ATLAS 800PLUS Base Unit and connecting the required cables, you can install your choice of option modules. Instructions for installing option modules are given in the user manuals for the chosen modules. POWER-UP As shipped, the ATLAS 800PLUS is set to factory default conditions.
Chapter 3 Operating the ATLAS 800PLUS METHODS OF OPERATING THE ATLAS 800PLUS You can access basic setup functions from the ATLAS 800PLUS Front Panel. However, to access all of the ATLAS 800PLUS functions, set up a Telnet session or use a VT-100 terminal emulation. In addition, T-Watch PRO provides limited configuration control. The following sections provide an overview of these methods of operating the ATLAS 800PLUS.
Chapter 3. Operating the ATLAS 800PLUS 1) ETHERNET S0) SYSTEM 2) CONFIG S1) 1) BAUD RT 9600 2) FLOW CTL 2) CHAIN PORT 3) TYPE : 4) UNIT ID S8) 5) INIT MODEM Figure 3-2. Example of Basic Front Panel Menu Navigation Setting Up the Unit ID using the Front Panel Menu, CONFIG Step Action 1 Activate CONFIG by pressing the Front Panel arrow keys or by pressing the number 2 on the Front Panel. (The cursor flashes on the number next to the activated selection.) Press Enter on the Front Panel.
Chapter 3. Operating the ATLAS 800PLUS Using Telnet To connect to the ATLAS 800PLUS via Telnet, define the IP address, set the subnet mask, and, typically, wet the default gateway IP address. The following Step/Action tables provide instructions for performing these tasks. You must define the IP address before attempting to connect via Telnet. Instructions for Defining the IP Address Step Action 1 Obtain an IP address for the ATLAS 800PLUS from your LAN administrator.
Chapter 3. Operating the ATLAS 800PLUS Instructions for Setting the Gateway IP Address Step Action 1 From the Front Panel, select 2) CONFIG, then S0) SYSTEM, then 1) ETHERNET. 2 When the submenu displays, select 3) DEF GATEWAY. 3 Enter the default gateway by entering each number followed by Enter to move to the next field. 4 Press Enter after keying in the entire address. You will need a default gateway if the LAN contains multiple segments.
Chapter 3. Operating the ATLAS 800PLUS Instructions for Setting Up an ATLAS 800 for VT-100 Terminal Mode Step Action 1 Set the baud rate on the VT-100 terminal to 9600 baud (8/N/1). 2 Use the Front Panel to set the ATLAS 800PLUS baud rate to match the terminal baud rate. Select 2) CONFIG, S0) SYSTEM, 2) CHAIN PORT, then 1) BAUD RATE.
Chapter 3.
Chapter 4 Using the Front Panel Use the Front Panel to select and set up the method of connectivity for controlling the ATLAS 800PLUS Base Unit and to monitor the operation and status of the Base Unit. Figure 4-1 identifies the display panels and the operation keys located on the Front Panel. Enter Module Status LCD Window Alarm Online Status Clear System LED Cancel Up and Down Arrows Test Status Home CSU Status LEDs Module Status LEDs Shift Module Slot Numbers Figure 4-1.
Chapter 4. Using the Front Panel Table 4-1. ATLAS 800PLUS Front Panel Description Feature Description LCD Window Displays menu items and messages in two lines by sixteen characters in a backlit liquid crystal display (LCD). It also displays alarm and status information. Enter Selects active menu items. To select a menu item, press the number of the item. The menu item flashes, indicating it is activated. Press Enter to select the menu item.
Chapter 4. Using the Front Panel Table 4-2. LED Descriptions For these LEDs... This color light... Indicates that... System Green (solid) No diagnosed system faults were found. Green (fast blink) Flash download is in progress. Yellow (solid) Fault was diagnosed, but the condition no longer exists. The condition will be recorded in the system log. Red (solid) An error condition is present with either the power supply or temperature. Red (fast blink) A fatal error occurred during flash download.
Chapter 4. Using the Front Panel OPERATION KEYS Operation keys are ATLAS 800 Front Panel keys that perform alternate functions. To activate an operation key, simultaneously press the Front Panel Shift key and the operation key that you want to activate, as shown in Table 4-3. Table 4-3. Operation Keys To do this... Press these keys... Access the active alarm display menus. Shift + Alarm (This function can be activated while any other menu item is in use.) Clear data/result fields in various menus.
Chapter 4. Using the Front Panel Selecting Front Panel Menus To do this... Go to this menu... See also page... Display the status of the ATLAS 800PLUS STATUS 4-7 Display the card type in each slot STATUS 4-7 Perform limited configuration of the ATLAS 800PLUS CONFIG 4-7 Monitor and modify miscellaneous settings UTIL 4-9 View a log of system events ALRM 4-11 Using the Front Panel Menus Menu Item/Activity... Comments...
Chapter 4. Using the Front Panel Editing a Data Field (Continued) Step 4 Action Select another data field to edit, or press Cancel to return to the submenu. Pressing Cancel prior to pressing Enter voids any data changes. The original data value is restored and the cursor returns to the submenu field. FRONT PANEL MAIN MENU The Front Panel Main menu provides limited configuration and control of the ATLAS 800PLUS. Figure 4-3 shows the submenu options provided.
Chapter 4. Using the Front Panel To help you follow the terminal menu hierarchy, the following notations are used. > MENUS » Submenus »» Sub-submenus STATUS The Status menu branch lets you view the status of the ATLAS 800PLUS Base Unit and any installed modules. » S0 System Displays status options that are available for the ATLAS 800PLUS Base Unit. Choose from Ethernet (see Ethernet Status on page 4-7) or Chain Port (see Chain Port Status on page 4-7).
Chapter 4. Using the Front Panel »» Ethernet Allows you to create and change configuration settings for the 10BaseT Ethernet connection. IP Address Uniquely identifies the ATLAS 800PLUS on a TCP/IP network. This address is composed of four decimal numbers, each in the range of 0 to 255, separated by periods. This value is set to 0.0.0.0 by default. The IP address is used for the 10BaseT Ethernet interface. Obtain the correct IP address from your LAN administrator.
Chapter 4. Using the Front Panel Unit ID Accesses the current Unit ID setting, which is the system identifier used for ADTRAN Data Link Layer Protocol (ADLP) configuration control (such as using T-Watch PRO). Editing or changing the Unit ID requires the use of a passcode if a passcode is defined. See Set Passcode on page 4-11 for details on working with passcodes. Unit Identification numbers must be between 2 and 9999. The number 1 is reserved for the PC.
Chapter 4. Using the Front Panel » Selftest Executes a system self-test, and the LCD displays the Pass or Fail when the test is complete. Options include Run Selftest, Show Results, and Clear Results. The Selftest option disrupts data flow. »» Run Selftest Initiates a self-test. When you select this option, the prompt Selftest, Are You Sure Y/N? displays. To initiate the self-test, select Y and press Enter. Select N and press Enter to cancel the self-test.
Chapter 4. Using the Front Panel »» Clear Results Resets the self-test log that you access with the Show Results option. When you select this option, the message Self-Test Log Clearing displays. After the command is finished executing, the message Self-Test Log Cleared displays. If you clear the message log, you cannot retrieve the data. » Set Passcode Provides security for Front Panel access.
Chapter 4. Using the Front Panel » View History Displays a time and date-stamped list of the alarms that have occurred in the ATLAS 800PLUS. Some alarm types include -A to indicate the alarm is active and -I to indicate the alarm is inactive. » Clear History Clears the alarm history log. When you clear the alarm history log, you cannot retrieve the data.
Navigating the Terminal Menu Chapter 5 TERMINAL MENU WINDOW The ATLAS 800PLUS uses a multilevel menu structure that contains both menu items and data fields. All menu items and data fields display in the terminal menu window, through which you have complete control of the ATLAS 800PLUS (see Figure 5-1). Menu Path Left Pane Right Pane Sys Tool Tip Port Status Extended Help System Time Navigation Help Figure 5-1.
Chapter 5. Navigating the Terminal Menu Window Panes When you first start a terminal menu session, the terminal menu window is divided into left and right panes. The left pane shows the list of available submenus, while the right pane shows the contents of the currently selected submenu. Window Pane Navigation Use the following chart to assist you in moving between and within the two window panes. To move... Press one of these keys...
Chapter 5. Navigating the Terminal Menu Additional Terminal Menu Window Features Sys Describes the status of the ATLAS base unit (system). Tool Tip Provides a brief description of the currently selected (highlighted) command. Port Status Displays status information, such as OK, WARN, or ALRM, about ports 1—8. Extended Help Displays information about selected commands (Ctrl-A). Navigation Help Lists characters used for navigating the terminal menu (Ctrl-Z).
Chapter 5. Navigating the Terminal Menu Move to the bottom of a screen. Z Backspace Ascend one menu level. Session Management Keystrokes To do this... Press this... Log out of a session. Ctrl-L Invalidate the password entry and return to the login screen. Ctrl-S Refresh the screen. Ctrl-R To save time, only the portion of the screen that has changed is refreshed. This option should only be necessary if the display picks up incorrect characters.
Chapter 5. Navigating the Terminal Menu To do this... Press this key... Paste the item stored in the clipboard, if the information is compatible. P You must confirm all pastes—except those to a single editable field. Increment the value of certain types of fields by one when you paste information into those fields. > Decrement the value of certain types of fields by one when you paste information into those fields. < Insert a new list item.
Chapter 5.
Chapter 6 Terminal Menu and System Control SELECTING THE APPROPRIATE MENU The terminal menu is the access point to all other operations. Each terminal menu item has several functions and submenus that identify and provide access to specific operations and parameters. Use the chart below to help you select the appropriate terminal menu. To do this... Go to this menu... For more info... Review and monitor general system information for the ATLAS 800PLUS. System Info See page 6-2.
Chapter 6. Terminal Menu and System Control SECURITY LEVELS To edit terminal menu items, you must have a password and the appropriate security level. Table 6-1 describes the six security levels. See Access Passwords on page 6-11 for additional information on working with passwords. Table 6-1. Password Security Levels Security Level Description 5 Read-only permission for all menu items—minimum rights. 4 Read permission for all menu items and permission to use test commands.
Chapter 6. Terminal Menu and System Control » System Name Security level: 3; Read security: 5 Provides a user-configurable text string for the name of the ATLAS 800PLUS. This name can help you distinguish between different installations. You can enter up to 40 alpha-numeric characters in this field, including spaces and special characters (such as an underbar). This name also displays on the LCD Front Panel.
Chapter 6. Terminal Menu and System Control Figure 6-2. System Status Menu » Event Log » Clear System Event Log Read security: 5 Displays the last 350 warning or failure messages sent—including the day, date, and priority of the message. The most recent messages display at the top of the list. The following read-only fields are available to review: Time Event Log/Time Displays the date (in mm/dd format) and the time (in hh:mm:ss format) that the event occurred.
Chapter 6. Terminal Menu and System Control » Ethernet Port Read security: 5 Displays status information about the Ethernet port. An asterisk (*) indicates activity for the item. The following read-only fields are available to review: I/F Status Indicates the current status of the 10BaseT port. Tx Frames Indicates the number of frames transmitted from the 10BaseT port since system startup. Rx Frames Indicates the number of frames received on the 10BaseT port since system startup.
Chapter 6. Terminal Menu and System Control » Configuration » Trunk Usage 0 (zero) available Provides a count of the number of times the quantity of available resources reached 0. Hour Data Shows availability information by hour for a 24-hour period. Reset Activates the reset of all accumulated availability statistics. Write security: 4; Read security: 5 Configures the statistics displayed under data tables. Display Formt Selects the statistics display format—Raw Data or %.
Chapter 6. Terminal Menu and System Control » Chain Port Tx Bytes Read security: 5 Displays the number of transmitted data bytes. » Chain Port Rx Bytes Read security: 5 Displays the number of received data bytes. » Chain Port Overrun Errs Read security: 5 Displays the number of overrun errors. » Chain Port Framing Errs Read security: 5 Displays the number of received framing errors. » Clear Chain Port Countrs Clears all chain port counters. Press Y to activate command.
Chapter 6. Terminal Menu and System Control » Session Timeout Write security: 3; Read security: 5 Defines the number of seconds the terminal session must remain idle before the session times out. You can enter zero to deactivate this option (the session will never time out). » Max Telnet Sessions Write security: 3; Read security: 5 Defines the maximum number of Telnet sessions that can be active at the same time. Enter a number between 0 and 100 in this field.
Chapter 6. Terminal Menu and System Control »» Port Type Write security: 2; Read security: 5 Specifies whether you use Direct or Dial mode. »» Port Speed Write security: 2; Read security: 5 Specifies the baud rate of the port. Select either 2400, 9600, 19200, or 38400. If you are using Dial for Port Type, ensure that the Port Speed setting matches the modem baud rate. »» Modem Initialization String Write security: 2; Read security: 5 Specifies the initialization string for a modem.
Chapter 6. Terminal Menu and System Control »» Traps Destination Write security: 3; Read security: 5 Defines the destination for SNMP traps as follows: IP Address Identifies the IP address to which the network manager sends traps. Community Defines the community name for trap destinations. This name must match the community name defined at the network management station. Trap Filtering Sets the minimum severity level required for a system event to generate an SNMP trap.
Chapter 6. Terminal Menu and System Control » Access Passwords Write security: 0; Read security: 5 Provides a way to edit passwords and, also, to add new users and passwords. All menu items are protected by passwords of varying security levels. By assigning different passwords to different security levels, the ATLAS system administrator can control which users can change various menu items. You can assign multiple passwords at the same access level.
Chapter 6. Terminal Menu and System Control Instructions for Changing Passwords Step Action 1 Select the Password field—a new Password field displays. 2 Type the new password in the Enter field. 3 Type the new password again in the Confirm field. The password can contain up to 12 alphanumeric characters. You can also use spaces and special characters in the password. »» Active Write security: 0; Read security: 5 Displays the number of users for each label that are currently logged into the system.
Chapter 6. Terminal Menu and System Control »» TCID Timer Write security: 3; Read security: 5 Specifies the length of time both endpoints attempt to negotiate an agreeable value for bearer channels and channel capacities before deciding the BONDING call has failed. »» Call Stagger Write security: 3; Read security: 5 Specifies the amount of delay between placing calls for outgoing BONDING sessions. Table 6-2 defines the call stagger values. Table 6-2.
Chapter 6. Terminal Menu and System Control formation on how to update firmware using this method, see TFTP Firmware Updates on page 11-4. The available update options vary depending on whether you select Slot 0, Slots 1 through 8, or All Modules of a Type. »» Module Slot Write security: 1; Read security: 5 Displays the slot you selected for firmware updating. When this option first appears, None Selected displays.
Chapter 6. Terminal Menu and System Control Restart at Specified Date and Time Lets you specify a date and time to automatically restart the updated module. (When you select this option, a new field called Restart Date and Time displays below the current field.) Restart Date and Time Write security: 1; Read security: 5 Defines the date and time to restart the system. • Enter the time using a 24-hour format (i.e., 23:00:00 for 11:00 pm). • Enter the date in mm-dd-yyyy format (i.e., 1030-1998).
Chapter 6. Terminal Menu and System Control on how to do this). For TFTP updates, you can cancel the process by selecting Cancel Update from this field. » Update Status Read security: 5 Displays the status of the current firmware update. These fields are identical to those defined in Current Update Status on page 6-15. » Config Transfer Write security: 3; Read security: 5 Used only with TFTP transfers.
Chapter 6. Terminal Menu and System Control »» Load and Use Config Write security: 3; Read security: 5 Retrieves the configuration file specified in the TFTP Server Filename field from the server. To start this command, enter Y to begin or enter N to cancel. If you execute this command, the ATLAS 800PLUS retrieves the configuration file, reboots, then restarts using the new configuration.
Chapter 6. Terminal Menu and System Control Idx Index number of the log Time Time and date of the log entry Sl ATLAS slot number Pt ATLAS port number Event Event description Result Shows Pass/Fail results The tests associated with the system controller include the following: This event... Logs this result... Flash Flash memory checksum verified. BootRom Boot ROM checksum verified. DSP RAM Memory associated with the DTMF DSP. RTC RAM Memory associated with the real time clock.
Chapter 6. Terminal Menu and System Control » Ping Write security: 5; Read security: 5 Allows you to send pings (ICMP requests) to devices accessible via the network. Only ping one session can be active at a time. »» IP Address Write security: 5; Read security: 5 Specifies the IP address to ping. »» Count Write security: 5; Read security: 5 Specifies the number of pings to send. The default number is, and the maximum value is 99.
Chapter 6. Terminal Menu and System Control » Reboot System Write security: 2; Read security: 5 Reboots the ATLAS 800PLUS. When you select this command, the following message displays: ** WARNING ** This will reboot the entire system! Press y to reboot the system, or n to exit the command. » Factory Default System Write security: 0; Read security: 0 Resets the entire system to the factory default settings. To reset the system, press y; to cancel this command, press n.
Chapter 7 Modules Terminal Menu To help you follow the terminal menu hierarchy, the following notations are used. > MENUS » Submenus »» Sub-submenus > MODULES Write security:3; Read security:5 The Modules menu provides options that allow you to configure and control the installed option modules as well as the controller T1/PRI ports. Figure 7-1 shows the Modules menu. Figure 7-1. Modules Menu The controller board (slot 0) has two T1/PRI interface ports.
Chapter 7. Modules Terminal Menu » Type Write security:3; Read security:5 Displays the type of module actually installed in the slot or the type of module you plan to install in the slot. The ATLAS 800PLUS automatically detects the type of module installed in each slot, and the Type field automatically defaults to the installed module type. You can also use this field to pre-configure a unit before actually installing modules by specifying the module that you want to install in each slot.
Chapter 7. Modules Terminal Menu » Status Read security:5 Displays status information on the ATLAS 800PLUS T1/PRI ports and other installed modules as follows: Online The module is enabled and is responding to the system controller’s status polls. This is the normal response of the system. No Response The module is enabled but is not responding to the system controller’s status polls. This response indicates a problem in the system or that the module is not installed.
Chapter 7. Modules Terminal Menu »» DS0 Status »» DS0 Alarms »» Sig Status 7-4 Prt Port number displayed. Loss of Signal (LOS) No signal detected on port interface. Red Alarm (RED) Not able to frame data received on the port. Alternately referred to as Out of Frame (OOF). Yellow Alarm (YELLOW) Remote alarm indicator (RAI) being received on port. Blue Alarm (BLUE) Receiving unframed all ones from the port alarm indicator signal (AIS).
Chapter 7. Modules Terminal Menu »» Performance: Current Write security:4; Read security:5 The performance fields – either current, 15 minute total, or 24 hour total – provide status on key performance measures as specified in ANSI T1.403 and AT&T TR54016 for each of the four T1/PRI ports as follows: Prt Displays the port number. CLR Clears information for the selected port. Press Enter when the cursor is over this field to clear the data. ES Errored Seconds.
Chapter 7. Modules Terminal Menu Code Write security:2; Read security:5 Matches the line code of the circuit to which it is connected (available from the network supplier). Tx Yellow Write security:3; Read security:5 (Auto Tx Yellow Alarm) Enables and disables the transmitting of yellow alarms. »» Test Tx PRMs Write security:3; Read security:5 (Transmit PRMs) Enables and disables the sending of PRM data on the facility data link (FDL).
Chapter 7. Modules Terminal Menu Remote LB Write security:4; Read security:5 (Remote Loopback) Sends a loopback code to a remote CSU. ANSI FDL Line (Requires ESF mode) ANSI FDL Pyld (Requires ESF mode) AT1 Inband line Pattern 61200226L1-1 Write security:4; Read security:5 Specifies the test pattern to be transmitted out the port.
Chapter 7.
Chapter 8 Dedicated Maps Terminal Menu OVERVIEW The Dedicated Maps menu assigns dedicated connections between any two ports in the ATLAS 800PLUS Base Unit. This chapter describes the Dedicated Maps menu items (see Figure 8-1). In addition, step-by-step instructions are provided for setting up a sample dedicated map (see Creating A Dedicated Map on page 8-6).
Chapter 8. Dedicated Maps Terminal Menu > ACTIVATE MAP Write security:3; Read security:5 Activates a dedicated map—automatically or manually. You can have up to five different dedicated maps, each with an optionally specified name. » Auto Automatically activates a particular dedicated map at the time and day specified in Activate Time (see Activate Time on page 8-5). » Maps 1—5 Lets you manually activate a specific dedicated map.
Chapter 8. Dedicated Maps Terminal Menu »» # (Index Number) Displays the number of the dedicated map connection. If you press I in this field, ATLAS 800PLUS adds another dedicated map connection, numbered consecutively. »» FROM Slt Write security:3; Read security:5 (From Slot) Specifies the slot to use for the FROM connection. When you select this option, a list of all of the slots and the modules installed in the slots displays. Pick the appropriate slot and press Enter.
Chapter 8. Dedicated Maps Terminal Menu Data Rate n This DS0 is already used in this Dedicated Map. N This DS0 is already used in this Dedicated Map and conflicts with this connection. Write security:3; Read security:5 Defines the data rate per DS0. If FROM Slt is an Nx port, the data rate per DS0 must be set. You can choose from 64 kbps or 56 kbps.
Chapter 8. Dedicated Maps Terminal Menu »» To Config Security level: 3; Read security: 5 Specifies the configuration for the To connection. The selections that display in this field are based on the type of module selected in the TO Slot option. You must input the following information (based on the type). The same options for setting DS0s are available for this command as with the FROM Config option.
Chapter 8. Dedicated Maps Terminal Menu . PBX ATLAS 800 T1-A T1-B T1-C Figure 8-2. Trunk Conditioning Example: Creating A Dedicated Map A Dedicated Map defines connections for dedicated bandwidth between ports, and grooms and cross-connects bandwidth between T1 ports. Any ATLAS port supporting dedicated bandwidth can be mapped to any other port supporting dedicated bandwidth (see the example in Figure 8-3). T1-A: DS0 1-8 Voice; DS0 9-24 Data V.35 A: Data T1-B: DS0 1-8 Voice; DS0 9-24 Data V.
Chapter 8. Dedicated Maps Terminal Menu step-by-step procedures for creating a sample Dedicated Map based on the connections and ports given in Table 8-1. Table 8-1. Connections and Ports Name ATLAS 800PLUS Port DS0s Name ATLAS 800PLUS Port DS0s T1: Data A Controller T1 Slot 0 Port 1 9-24 RBS Off V.35 - A Quad V.35 Slot 2/Port 1 N/A T1: Data B Controller T1 Slot 0/Port 2 9-24 RBS Off V.35 - B Quad V.35 Slot 2/Port 2 N/A T1: Data C Quad T1/PRI Slot 1/Port 1 9-24 RBS Off V.
Chapter 8. Dedicated Maps Terminal Menu Figure 8-4. Slot 0 Module Configuration Menu Defining the Connections Begin by navigating to Dedicated Maps / Create/Edit Maps and naming your map. Navigate to Dedicated Maps / Connects. The Connects submenu defines the connections necessary to route the required bandwidth. Refer to Table 81 to define each of the necessary connections. For this procedure, first define the data connections, and then define the voice connections.
Chapter 8. Dedicated Maps Terminal Menu Instructions for Defining Data Connections (Continued) Step Action 6c Paste this information onto a new connection line by positioning the cursor over the index numbers of the new connections, and pressing P. 7 Modify these connection lines to complete the connections for data. Instructions for Defining Voice Connections Step Action 1 Select the FROM Slot and Port for the first voice connection (i.e., Slot 0/Port 1 for T1-A Voice).
Chapter 8. Dedicated Maps Terminal Menu Figure 8-5.
Chapter 9 Dedicated Circuit Backup and Circuit Status OVERVIEW This chapter describes the configuration of dedicated circuits for backup and discusses the Circuit Status menu. Dedicated Circuit Dial Backup Setup In Figure 9-1, the host ATLAS 800PLUS has a fractional T1 of 16 DS0s going to the T1 cloud, which is then DACSed out to two different remote sites, 8 DS0s each.
Chapter 9. Dedicated Circuit Backup and Circuit Status Configuration First, configure your dedicated maps normally. Refer to Chapter 8 for more information on configuring Dedicated Maps. One thing to remember is that the endpoint receiving the backup data (i.e., the Nx endpoint) needs to be in the From column. All dedicated circuit dial backup configuration is the Dial Plan/User Term menu. For Slot/Svc, select Circuit Backup.
Chapter 9. Dedicated Circuit Backup and Circuit Status > INTERFACE CONFIGURATION » Originate/Answer The following selections are available for the Originate/Answer menu item. Originate The endpoint will originate the backup call. Answer The endpoint will answer any incoming calls, but will only go into backup if an error is detected. Answer Any The endpoint will answer any incoming calls and go immediately into backup. » Outgoing Call Type This only applies to originating endpoints.
Chapter 9. Dedicated Circuit Backup and Circuit Status » Restore Delay This only applies to originating endpoints. The amount of time to delay after clearing an alarm before coming out of backup. If the circuit goes into alarm before this time has expired, the endpoint will remain in backup. » Max Num Redials This only applies to originating endpoints. The backup endpoint will attempt this many retries before giving up and declaring a backup failure.
Chapter 9. Dedicated Circuit Backup and Circuit Status CIRCUIT STATUS MENU The Circuit Status menu allows the user to view at a glance the status of any circuits that are configured for dedicated circuit backup. Figure 9-3 shows the Circuit Status menu. Figure 9-3. Circuit Status Menu > FROM Write security:3; Read security:5 Indicates the slot, port, and name of the endpoint that is configured for backup. > MAN (MANUAL BACKUP) Use this activator to force a link into/out of backup.
Chapter 9. Dedicated Circuit Backup and Circuit Status > > BKUP STATUS (BACKUP STATUS) LINE STATUS String indicates the current status of the dedicated line. The following selections are available for the Backup Status menu item. FB Backup is forced through the interface menu. FR Restoral is forced through the interface menu. Primary The link is active. Dialing Attempting to dial the backup link. Backup Failed Exceeded Max Num Redials.
Chapter 9. Dedicated Circuit Backup and Circuit Status > TEST This only displays if an endpoint is configured for Originate. This submenu is used to monitor regular test call status for the backup endpoint. The record label displays the number of successful tests and the number of test failures, respectively. » Last Run Time Only displays if a test call has been attempted. This displays the date of the last attempted test call. » Next Run Time Only displays if a test call is scheduled.
Chapter 9.
Chapter 10 Dial Plan Terminal Menu OVERVIEW The Dial Plan submenus (see Figure 10-1) set global ATLAS switch parameters as well as individual parameters for each ATLAS port handling a switched call. The individual ports are separated into two port types: network and user. Network ports terminate a connection from the Network. User ports terminate incoming calls and, in turn may be connected to user , equipment.
Chapter 10. Dial Plan Terminal Menu Network Term # Slot/Svc Port/PEP Sig Out # Accept # Src ID Accept Number Search Data 64K Data 56K # Reject Number Data 64K Data 56K Audio Speech Out#Rej Ifce Config These submenus vary depending on the Module. # Slot/Svc Port/PEP Sig In # Accept Dial Plan User Term # Src ID Accept Number Search Data 64K Data 56K # Reject Number Data 64K Data 56K Audio Speech Out#Rej Ifce Config Global Param These submenus vary depending on the Module.
Chapter 10. Dial Plan Terminal Menu > NETWORK TERM This menu allows the user to define option parameters for ports which terminate a connection from the Network (PSTN). In applications where two ATLAS units are used in a point-topoint configuration, a port in the ATLAS at one end would act as the Network (User Termination), while the ATLAS at the opposite end would be terminating a “Network” connection.
Chapter 10. Dial Plan Terminal Menu »» Accept Numbers This field designates which numbers this end point will pass on toward the Network (PSTN). The accept list may consist of multiple entries. The numbers are defined using “wild cards”: X = Any single digit N = Any single digit 2—9 $ = Any number of digits of any value 9 = This specific number [1,2,3...] = A single digit in this group Example: 1-800-$ would only permit toll free long distance calls to 1-800.
Chapter 10. Dial Plan Terminal Menu »» Reject Number This field identifies which numbers this end point will not pass on toward the Network (PSTN). The reject list may consist of multiple entries. The reject list may be used to more easily specify the call filtering desired. The “wild cards” are identical as in Outgoing Call Accept. The Reject list takes precedence over the Accept list. For example, 1- 900-$ would reject all 1-900 long distance calls, and 1-$ would reject all long distance calls.
Chapter 10. Dial Plan Terminal Menu » In#Accept Write security: 3; Read security: 5 This submenu defines the parameters for incoming calls that ATLAS 800PLUS will accept from the Network. »» Source ID Write Security: 3 Read Security: 5 This field identifies the ID of the call sources that this endpoint will accept calls from.
Chapter 10. Dial Plan Terminal Menu Primary Search The Search parameter instructs ATLAS which order to search for an accept number match. Normally all searches are set to Primary. The Secondary search selection would be used to force ATLAS to only accept a call at this end point if all Primary end points were unavailable. For example, all long distance calls should go out a PRI directly to an IXC (MCI, ATT, etc.) and local calls should go out a T1 to the LEC.
Chapter 10. Dial Plan Terminal Menu > GLOBAL PARAM Set ATLAS options which apply to all switched operations, both incoming and outgoing calls. » End of Number Timeout Write security: 3; Read security: 5 This parameter sets the length of time ATLAS will wait before assuming the outgoing dialed number is complete. The default value is six seconds. This timeout will only be invoked if the dialed number does not match one of the patterns set in the Number Complete Template menu.
Chapter 10. Dial Plan Terminal Menu » Automatic Routeback Rejection # Denotes an Entry Number (MAX 50). Press INS/DEL to insert/delete any entry. Prefix Sets the prefix for the number type. Only digits 0 and 1 are allowed (MAX 6). Pattern Modifies an entry when you press Enter (MAX 40). Number Typ Lists valid selections when you press Enter.
Chapter 10. Dial Plan Terminal Menu »» Number of DS0s Write Security: 3 Read Security: 5 Defines the number of DS0s used for calls on this PRI. DS0 24 is assumed to be used by the PRI for the D channel. »» Outgoing Number Conversion Write Security: 3 Read Security: 5 This item defines the rules for converting as-dialed numbers into ISDN number type and plan. As dialed Send digits provided as unknown number type. ISDN National pref Convert to ISDN type, using the 10-digit national form if possible.
Chapter 10. Dial Plan Terminal Menu would almost always be correct. If less than All digits are sent, then the prefix is defined below. »» Outgoing Caller ID Write Security: 3 Read Security: 5 Inserts a called ID based on the following selections. Send as provided ATLAS forwards whatever ID it receives (including None). Substitute if ATLAS inserts a User-defined ID value if no value is renot present ceived.
Chapter 10. Dial Plan Terminal Menu QUAD T1/PRI MODULE (NETWORK TERMINATION/RBS) When you are working in the Network Termination section of the Dial Plan menu, the Slot is defined as a T1/PRI module, and Sig is set to RBS, the following interface configuration options are available: »» First DS0 Write security: 2; Read security: 5 Defines to ATLAS the DS0s which will be used for this endpoint. These are the DS0s which ATLAS will use to send and receive calls to and from the Network (PSTN).
Chapter 10. Dial Plan Terminal Menu »» Direct Inward Dialing Write security: 3; Read security: 5 This defines to ATLAS whether or not DID is being used by the Network. If DID is Enabled, then the following information must be defined: DID Digits Write security: 3; Read security: 5 Transferred Defines the number of digits sent to ATLAS from the Network if DID is used. DID Prefix Write security: 3; Read security: 5 Defines to ATLAS the prefix digits which are not received as a part of the DID number.
Chapter 10. Dial Plan Terminal Menu • When creating the Call Accept list, specify a Source ID(s) as well as a dialed number or range of dialed numbers to accept. For example, an application requires that all calls originating from Port 1 of the Quad T1/PRI module in Slot 1 be switched to Port 4 of that same module. Assign a unique Source ID (e.g., 7) to Port 1 of the module, and then configure Port 4 to only accept calls from that unique Source ID (7).
Chapter 10. Dial Plan Terminal Menu versus data calls. A setting of Normal indicates no special facilities have been subscribed. »» Called Digits Transferred Write security: 3; Read security: 5 Defines to ATLAS the number of called-number digits to forward. When attached to a PBX, the PBX may be provisioned to expect to receive fewer than all of the called digits of the incoming call. This would normally be set to All.
Chapter 10. Dial Plan Terminal Menu QUAD T1/PRI MODULE (USER TERMINATION/RBS) When you are working in the User Termination section of the Dial Plan menu, the Slot is defined as a T1/PRI module, and Sig is set to RBS, the following configuration options are available: »» First DS0/Number of DS0s Write security: 3; Read security: 5 Defines to ATLAS the DS0s which will be used for this end point. These are the DS0s which will be used by ATLAS to send and receive calls to and from User equipment (PBX).
Chapter 10. Dial Plan Terminal Menu » Caller ID Number Write security: 3; Read security: 5 Defines the number for ATLAS to use to provide Caller ID to the Network for outgoing calls sent through this end point. This option only displays if Direct Inward Dialing is set to Disabled. This item is optional. The Caller ID number must be specific (i.e., no “wild cards”).
Chapter 10. Dial Plan Terminal Menu »» Ports Available Indicates which of the four ports of the Quad Nx56/64 module have already been defined either in another switched end point (indicated by “s”) or in a Dedicated Map (indicated by “n”). This field is read-only. »» Number of Ports Defines to ATLAS how many of the ports could be used to answer calls to the number(s) defined in the Accept Call list. You can enter numbers 1 through 4.
Chapter 10. Dial Plan Terminal Menu This option allows a selected quantity of the Most Significant Digits (MSD) Phone Number The phone number(s) assigned to this BRI phone line. SPID Number This entry must match the SPID number(s) which have been set in the Network’s ISDN switch (or in the PBX) for this BRI line. A SPID must be entered for each phone number. Calls The number of calls (1 or 2) which can be received or sent on this number/SPID.
Chapter 10. Dial Plan Terminal Menu OCTAL BRI MODULE (USER TERMINATION) The Octal BRI with a “U” interface acts as the Network while interfacing to user equipment (terminal adapters). When you are working in the Network Termination section of the Dial Plan menu and the Slot is defined as a UBRI-8 module, the following interface configuration options are available: »» Switch Type Write security: 2; Read security: 5 Defines the type of ISDN switch that ATLAS will simulate.
Chapter 10. Dial Plan Terminal Menu The following options are only available if Outgoing Caller ID is not set to Send as Provided. »» ID Presentation Specifies the presentation of the caller ID information. »» ID Number This is the substitute number for the caller ID information. CREATING DIAL PLANS—EXAMPLES The ATLAS Dial Plan acts as the numbering plan for switched connections.
Chapter 10. Dial Plan Terminal Menu Example 2 Point-to-Point Connection Dial Plan Configuration In this example, ATLAS A operates as the network while ATLAS B terminates the network. That is, ATLAS A emulates the network and its PRI interface acts as the user termination. The PRI interface of ATLAS B acts as the network termination (see Figure 10-4). BRI ATLAS A USER BRI USER T1 from PBX USER User Term ATLAS B PRI Interface Network Term USER BRI USER BRI USER DSX T1 to PBX Figure 10-4.
Chapter 10. Dial Plan Terminal Menu Instructions for Configuring the Ports for Example 3 Step Action 1 Prior to setting up the Dial Plan, you must configure the Controller T1/PRI interfaces. 2 This configuration action only brings up the T1 transport; set the BRI configuration (SPID and phone number) as part of the Dial Plan. Instructions for Setting Up Dial Plan for Example 3 Step Action 1 Determine the network and the attached equipment (video equipment and PBX) provisioning (see Table 10-1).
Chapter 10. Dial Plan Terminal Menu Table 10-1. Network and Attached Equipment Provisioning Network PRI Type of provided PRI switch National ISDN DMS 100 custom 4ESS custom 5ESS custom DID- number of digits Type of provided BRI switch National ISDN DMS 100 custom 5ESS custom SPID(s) and phone number(s) provisioned for the BRI line User Equipment PRI Switch type the user equipment expects to interface to (ATLAS supports 4ESS custom and 5ESS custom). DID Number of digits.
Chapter 10. Dial Plan Terminal Menu Table 10-3. User Terminations NAME BRI-D BRI-E BRI-F PORT Octal BRI Slot 1, Ports 4-5,6 INCOMING ACCEPT # 888-1001 (D); 888-1002 (E); 888-1003 (F) OUTGOING REJECT # Blank - No called number will be rejected. OTHER BRI type: 5ESS SPID # to match Video Equipment provisioning. Phone #s: 888-1001 (D); 888-1002 (E); 888-1003 (F) Phone numbers must match phone numbers provisioned in video equipment. PRI-B Controller T1 Slot 0, Port 2 888-1010 This forms a hunt group.
Chapter 10. Dial Plan Terminal Menu Setting PRI A Global Param Step Action 7 Back out of the connection to the index number column by pressing ESC on the keyboard. 8 Insert three more connections into the list for the BRI lines by typing the letter I three times. Enter Out#Accept and Out#Reject numbers for Slot 1/ Port 1.
Chapter 10. Dial Plan Terminal Menu Figure 10-6. Completed Network Map Setting User Term Connections Step Action 1 Navigate to User Term. 2 Enter connections for BRI D,E, and F in the same manner as BRI A, B, and C: use the copy (C) and paste (P) commands to enter the appropriate Out#Accept and Out#Reject numbers. 3 Ensure that the SPID and Phone entries under Ifce Config match the SPID and phone numbers of the attached equipment.
Chapter 10. Dial Plan Terminal Menu Figure 10-7. Completed User Map A connection is not actually made (available) until you press Esc to move the cursor to the index number or move the cursor onto another connection line.
Chapter 11 Updating Firmware OVERVIEW To provide feature enhancements in the future, ATLAS 800PLUS supports firmware updating by field personnel. Two transfer methods are available for use in updating any modules that contain Flash memory, including the ATLAS 800PLUS system controller. The first transfer method is via the ATLAS 800PLUS Chain-In port using XMODEM protocol. The second transfer method is via the ATLAS built-in Ethernet port using TFTP (Trivial File Transfer Protocol).
Chapter 11. Updating Firmware Updating Firmware using XMODEM Before beginning this procedure, • you must have a level 2 password for updating any module within ATLAS 800PLUS. Please consult the ATLAS 800PLUS administrator if you do not know the password. • you must obtain the appropriate update file for the particular module from ADTRAN Technical Support at (888) 4ADTRAN (423-8726). • you may want to review Update Firmware on page 6-13.
Chapter 11. Updating Firmware Instructions for Updating Firmware Using XMODEM (Continued) Step Action From the terminal emulation software, begin the XMODEM upload by using the appropriate command sequence. (If necessary, refer to terminal emulation software documentation for help. Also, when specifying the filename, ensure that the file transferred is the one provided by ADTRAN. Otherwise, the update will not complete successfully.
Chapter 11. Updating Firmware TFTP FIRMWARE UPDATES ATLAS 800PLUS supports firmware updates to any module via the 10BaseT Ethernet port using TFTP from a network server. The network server must be capable of supporting TFTP server requests from the TFTP client within ATLAS 800PLUS. Updating Firmware using TFTP Before beginning this procedure, • you must have a level 2 password to perform updates of any modules within ATLAS. Please consult the ATLAS administrator if this password is not known.
Chapter 11. Updating Firmware Instructions for Updating Firmware Using TFTP (Continued) Step Action 8 View Current Update Status to verify the progress of the current firmware update or any errors encountered during the download process (see Current Update Status on page 6-15). Select Begin Firmware Update to start the update process. Enter Y to confirm the transfer and to set up the module to receive the TFTP upload.
Chapter 11. Updating Firmware Table 11-1. TFTP Upload Messages (Continued) Message Meaning Error: Illegal Operation An unknown operation was detected by ATLAS when transferring the update file from the TFTP network server. Error: User Aborted Indicates the user selected Cancel Update to abort reception of the update file from the TFTP network server. Figure 11-2.
Chapter 12 SNMP Management SNMP As local area network (LAN) environments became standardized over the past ten years, multivendor equipment grew with competition. It became necessary to manage various vendor equipment from a single control console. Thus, Simple Network Management Protocol (SNMP) emerged as the standard for managing commercial TCP/IP networks.
Chapter 12. SNMP Management SNMP TRAPS An SNMP trap is a message sent by a network device, such as the ATLAS 800PLUS, to report an operational anomaly or alarm condition. Trap Destination List A trap destination list contains information about sites designated to receive SNMP traps. You can configure this list via a Telnet session or the VT-100 terminal menu. The ATLAS 800PLUS supports up to four trap destination lists. By default, the destination list is empty.
Chapter 12. SNMP Management the system controller, the coldStart trap would not generate to that destination because the coldStart trap severity level is defined as Normal. (Recall that each trap event has a severity level: Disabled, Informational, Normal, Warning, Minor, Major, and Critical.) 3. Control certain traps through SNMP of specific MIB variables. These variables are outlined in the remainder of this chapter. Standard Traps Table 12-2 describes the standard traps supported by ATLAS. Table 12-2.
Chapter 12. SNMP Management Table 12-3. DS1 SNMP Traps Alarm Severity Description adATLAS800NoAlarm Warning No alarms are present. adATLAS800RxYellow Minor The Far end is experiencing Red Alarm (a.k.a. Yellow Alarm). adATLAS800TxYellow Warning The Near end is sending Loss Frame Indication (a.k.a. Yellow Alarm). adATLAS800RxAIS Minor The Far end is sending Alarm Indication Signal (a.k.a. Blue Alarm). adATLAS800TxAIS Warning The Near end is sending Alarm Indication Signal (a.k.a.
Chapter 12. SNMP Management Table 12-4. DS1 Current Alert SNMP Traps (Continued) Current Alert Severity Description adATLAS800CurrentUAS Major The current interval is unavailable. adATLAS800CurrentCSS Warning The current interval path code violations have been exceeded. adATLAS800CurrentLES Warning The current interval line errored second threshold has been exceeded. adATLAS800CurrentCV Warning The current interval line code violation threshold has been exceeded.
Chapter 12. SNMP Management Table 12-5. Total Alert Traps Total Alert Severity Description adATLAS800TotalLES Warning The total interval line errored second threshold has been exceeded. adATLAS800TotalLCV Warning The total interval line code violation threshold has been exceeded. When one of the Total Alert thresholds is exceeded, the corresponding event bit is set to 1 in the adDS1TotalAlert variable in the DS1 alert table.
Chapter 13 ADTRAN Utilities OVERVIEW ADTRAN delivers several PC software utilities along with the ATLAS 800PLUS. These utilities are located on the three diskettes that came with your shipment. They also include MIB files (located in the MIB directory). Review the readme file (Readme.txt) for the latest information about the utilities. The utilities make interfacing with the terminal menu and transferring configuration files to and from TFTP servers easier. The utilities all run on Microsoft Windows 3.
Chapter 13. ADTRAN Utilities SysLog GUI Figure 13-1 on page 13-2 shows the SysLog Host GUI. The conventional Menu Bar is described below beginning on page 13-3 (see also Figure 13-2). Other features are described here. Figure 13-1. ATLAS SysLog Host GUI Monitor The Monitor feature allows all SysLog messages to be pre-filtered by System Name, Source, Slot and Port before displaying these messages to the user and logging the message to the pre-designated monitor log file.
Chapter 13. ADTRAN Utilities Menu Bar The SysLog Menu Bar provides common functions. The Menu Tree shown in Figure 13-2 shows the structure.
Chapter 13. ADTRAN Utilities LOG FILES Erases log files, defines Red events, sets priorities and action to be taken when an event occurs, and clears Red events. (See Define RED Events on page 13-4.) » Erase Log Files The SysLog utility, by default, stores all messages of a certain priority in a specified local log file or facility. These files are named LOCAL0.txt, LOCAL1.txt, LOCAL2.TXT, and so on To erase the file, click on this menu.
Chapter 13. ADTRAN Utilities The Telnet menus include Session, Edit, Options, Capture, and Help (see the menu tree in Figure 13-3 on page 13-5). Session Edit Telnet Options Connect Disconnect Transfer Cfg Exit Host Name Port Edit Entry Add New Delete Connect Copy Paste Colors Local Echo Auto Repeat File Background Bold Text Start Cfg Capture Stop Cfg Capture Capture Buffer Size Save Buffer As Screen Capture Help Contents IP Status About Express Feature Only Figure 13-3.
Chapter 13. ADTRAN Utilities > SESSION MENU Click on Session to open the Telnet session. » Connect Opens dialog box for setting Host Name and Port parameters for a Telnet session. Also lets you Edit Entry, Add New entry, and Delete stored entries. When the parameters are set, click Connect to make the connection. Click Cancel to end the session. »» Host Name Accepts and stores host names. You may either enter a name, an IP address, or a domain name directly from this field.
Chapter 13. ADTRAN Utilities » Transfer Cfg This feature is used with Express products primarily for sending configuration files to the unit. » Exit Ends the Telnet session and closes the Telnet screen. > EDIT MENU Provides Copy and Paste commands. > OPTIONS MENU Provides viewing alternatives for the terminal screen. » Colors Three options change the color of the background window (BackGround), bold highlights (Bold), and text (Text). » Local Echo Echoes each character that you enter.
Chapter 13. ADTRAN Utilities VT-100 UTILITY Use the VT-100 to configure an ATLAS 800 which is directly connected to a PC. The VT-100 display is almost identical to the Telnet display. For a detailed description of how to work with the Telnet program, refer to Navigating the Terminal Menu on page 5-1, and for a detailed description of the VT-100 interface, see VT-100 Utility on page 13-8. If you need help setting up the ATLAS 800 for a VT-100 session, refer to Using VT-100 Terminal Emulation on page 3-4.
Chapter 13. ADTRAN Utilities » Disconnect Closes a specified serial port at the end of a VT-100 session. » File Transfer Uploads and downloads files to and from an ATLAS. »» XMODEM CRC Selects the XMODEM file transfer protocol. »» ASCII Cfg Files Selects ASCII transfer mode. Primarily useful for configuration transfers for the Express products. > EDIT MENU Identical to the Telnet Edit Menu (see Edit Menu on page 13-7). > PORT MENU Changes serial COM port Settings.
Chapter 13. ADTRAN Utilities > HELP MENU Provides on-line help and information about the version number. » Contents Opens on-line help. » About Displays version and owner information. TFTP SERVER The TFTP Server utility transfers ATLAS 800 configuration files to and from a TFTP server. You can install this program on a PC running any version of Microsoft Windows. The configuration of an ATLAS 800 can be saved offline as a backup file.
Chapter 13. ADTRAN Utilities Figure 13-6. TFTP Server Interface Only one configuration transfer session (upload or download) may be active at a time. The TCP/IP parameters are not saved or overwritten as part of an ATLAS 800 unit’s transferred configuration to allow sending identical configurations to multiple units. When you start this program, a port is automatically opened. > SERVER MENU Provides enable, disable, abort, and exit options. » Enable Enables the TFTP server.
Chapter 13. ADTRAN Utilities > HELP Provides on-line help and version information. » Contents Opens on-line help. » About Displays version and owner information. STATUS FIELD This field displays general information about port and transfer status. This field is read-only. The unlabeled field in the center of the screen displays prompts about the status of active transfers, such as bytes transferred and received. METER FIELD The XMIT meter provides a visual record of the transfer process.
Chapter 13. ADTRAN Utilities To save the current configuration, follow these steps: Step Action 1 Use Telnet and log in to the ATLAS 800 for which you want to save the configuration file. 2 Select the System Utility menu, then the Config Transfer menu. 3 Set the TFTP Server IP Address to the IP address of the machine running the TFTP server program. (If you are using the ADTRAN TFTP server, the IP address displays in the Status field.
Chapter 13. ADTRAN Utilities Also, a level 3 or better password is required for performing a configuration upload. Please consult the ATLAS administrator if level 3 access is not available. Instructions for Retrieving a Configuration from TFTP Server Step Action 1 Use Telnet to log in to the ATLAS 800PLUS to which you want to upload a configuration file. 2 Select the System Utility menu, then the Config Transfer menu.
Appendix A System Event Logging This section describes the entries that may be logged by the system event log. Of particular importance is the log event’s Category – this is the minimum severity level that must be set in order that the event be logged. Use caution when changing Categories from their default levels. If too many sources have their Category values set too low, the number of messages being logged in a given period can be very large.
Appendix A. System Event Logging Table A-1. Source: System Event Category Console Log String Front Panel Display String System Cold Start Normal Generated 5 seconds after the completion of system initialization. Cold Start COLD START SNMP Authentication Failure Info Generated if the ATLAS receives an SNMP request from an SNMP manager defined in the ATLAS SNMP Communities list but with a community name that does not match the community name defined in the SNMP Communities list.
Appendix A. System Event Logging Table A-2.
Appendix A. System Event Logging Table A-3.
Appendix A. System Event Logging Table A-4.
Appendix A. System Event Logging Table A-4.
Appendix A. System Event Logging Table A-6.
Appendix A. System Event Logging Table A-6.
Appendix A. System Event Logging Table A-6. Source: ISDN (Continued) Event Category Console Log String Front Panel Display String Call received Information Call to ATLAS: received n/a Incoming call refused Information Incoming call to refused n/a Incoming call accepted Information Incoming call to accepted n/a In addition to the above, certain recognized ISDN cause codes are sent to the event log from the ISDN Message facility.
Appendix A. System Event Logging Table A-7.
Appendix A. System Event Logging Table A-7. ISDN Cause Codes (Continued) Cause Code Message Code Category INCOMPATIBLE_DEST 88 Major INVALID_MSG_UNSPEC 95 Major MANDATORY_IE_MISSING 96 Major NONEXISTENT_MSG 97 Major WRONG_MESSAGE 98 Major BAD_INFO_ELEM 99 Major INVALID_ELEM_CONTENTS 100 Major WRONG_MSG_FOR_STATE 101 Major TIMER_EXPIRY 102 Major MANDATORY_IE_LEN_ERR 103 Major PROTOCOL_ERROR 111 Major INTERWORKING_UNSPEC 127 Major Cause Code IEs that are non-Q.
Appendix A. System Event Logging Each Cause Code IE log entry will end with a location designation. These designations are shown below: Table A-8. Cause Code Log Entries Code Location U User LPN Private network serving the local user LN Public network serving the local user TN Transit network RLN Public network serving the remote user RPN Private network serving the remote user INTL International network INWK Network beyond internetworking point Table A-9.
Appendix A. System Event Logging Table A-11. Source: ISDN Information Elements Event Category Console Log String Front Panel Display String ISDN Information Elements.
Appendix A.
Appendix B Troubleshooting Power-up Self Test Fails Modules seated improperly, module failure Remove all modules and cycle power to the unit. If self test still fails, call Technical Support and report the results. If the self test now passes, re-insert modules one at a time, running the self test after installing each module. When an installed module causes the self test to fail, note it and report results to tech support.
Appendix B. Troubleshooting Cannot pass data from T1 interface to V.35 port Misconfiguration, improper cabling • Verify that the T1 signal is being received. If not, check that the cabling is correct. • Verify that the T1 is being received without errors. If not, double-check that framing and coding are set properly. • Verify that desired dedicated map is active. • Verify that bandwidth is mapped to the correct V.35 port. • Verify that the V.
Appendix B. Troubleshooting Cannot establish Telnet session with ATLAS Max Telnet sessions set to 0, IP address of ATLAS does not match remote host IP address 61200226L1-1 • Verify that the ethernet connection is in place, check IP addresses programmed in ATLAS and in the Telnet client, verify that session timeout value is not set too low. • Check for ethernet port activity on the front panel. Make sure the link is up, and data is being transmitted and received.
Appendix B.
Appendix C Warranty and Technical Support Information WARRANTY AND CUSTOMER SERVICE ADTRAN will replace or repair this product within five years from the date of shipment if the product does not meet its published specifications or if it fails while in service. For detailed warranty, repair, and return information refer to the ADTRAN Equipment Warranty and Repair and Return Policy Procedure. Return Material Authorization (RMA) is required prior to returning equipment to ADTRAN.
Appendix C. Warranty and Technical Support Information Repair and Return If ADTRAN Technical Support determines that a repair is needed, Technical Support will coordinate with the Customer and Product Service (CAPS) department to issue an RMA number.
Appendix D Acronyms and Abbreviations AMI alternate mark inversion ANI automatic number identification B8ZS bipolar eight zero substitution BRI Basic Rate ISDN bps bits per second CPE customer premise equipment CSU channel service unit CTS Clear to send DACS Digital Access Cross-Connect System DCE data communications equipment DNIS dialed number identification service DS0 digital service, level 0 (64 kbps) DSU data service unit DTE data terminal equipment DTMF dual tone multif
Appendix D.
Appendix E Glossary 10BaseT Ethernet connection The ATLAS 800 RJ-48C port that provides Ethernet LAN connection for TFTP, SNMP, and Telnet. AMI alternate mark inversion. A Layer 1 line code used in a T1 carrier. Zeros are transmitted as zero volts, and ones are transmitted as pulses that alternate polarity. Although B8ZS is an enhancement to AMI, B8ZS and AMI are normally referred to as mutually-exclusive options for a T1. (See also B8ZS.) ANI Automatic Number Identification.
Appendix E. Glossary byte Eight bits of information composed of zeros or ones, one of which may include a parity bit. BRI Basic Rate ISDN. An ISDN service that offers two bearer (B) channels. One channel (64 kbps) is used for data transfer and as a data-link. The second channel (16 kbps) is used for signaling and control information. clocking An oscillator-generated signal that provides a timing reference for a transmission link.
Appendix E. Glossary DS0 Digital signal (or service) having a transmission rate of 64 kbps intended to carry one voice channel (a phone call). Also called a fractional T1 because it bridges the gap between 56-kbps direct dial service (DDS) and a full T1 implementation (24 channels). DSU data service unit. A device used with a CSU to support digital communications by converting signals. (See also CSU.) DTE Data terminal equipment. The portion of a data terminal that interfaces to the end-user’s equipment.
Appendix E. Glossary LAN local area network. Group of computers and peripheral devices connected by a communications channel, limited by distance. LCD liquid crystal display. Alphanumeric characters that appear in a display area as a result of light reflecting off a special crystalline substance. leased line A telecommunication facility or link reserved for the exclusive use of one customer. Also called a dedicated line.
Appendix E. Glossary option modules Any optional, hot-swappable module that can be added to the ATLAS 800 system for a variety of applications. See also overbooking ATLAS 800 feature that reduces telecommunications expenses by allowing you to over-subscribe switched bandwidth for situations where simultaneous access to the network by every subscriber is not required. PBX private branch exchange. A telephone system usually owned by the customer that serves a particular location.
Appendix E. Glossary T3 Module One of the ATLAS 800 option modules. The T3 Module provides one or two channelized T3 interfaces. TCP/IP Transmission Control Protocol/Internet Protocol. A set of communications protocols that encompasses media access, packet transport, session communications, file transfer, electronic mail, and terminal emulation. TDM Time Division Multiplexing.
Index Symbols # 8-3 Numerics 10-BaseT connection 2-7 pinout 2-7 port 2-3 status 6-5 15 minutes performance 7-5 24 hour performance 7-5 A abort 13-11 accept numbers 10-4, 10-6 access passwords 6-11 access rights 6-11 activate dedicated map 8-2 front panel 4-2 time 8-5 activating operation keys 4-2 active alarm 4-11 add password 6-11 address ADLP 6-7 ADLP address 6-7 ADTRAN utilities 13-1 ADTRAN data link layer protocol address 6-7 alarm blue 7-4 red 7-4 status 7-3 system 6-5 yellow 7-4, 7-6 yellow auto TX
Index FR 9-5, 9-6 primary 9-6 backup timing source 6-7 bantam test jack 2-3 baud rt 4-8 begin firmware update 6-15 BES 7-5 blinking green module status LED 4-3 blinking green system LED 4-3 blinking red module status LED 4-3 blinking red system LED 4-3 blue alarm 7-4 BONDING Config 6-12 bonding configuration 6-12 boot ROM rev 6-3 bootROM 6-18 bursty errored seconds 7-5 C Call Stagger 6-13 call stagger values 6-13 call type 10-18 called digits transferred 10-10, 10-15 caller ID number 10-17 cancel 4-1, 4-4
Index connection activate 8-2 control in / chain in 2-4 create/edit 8-2 current 8-2 dedicated 7-6 ethernet 10BaseT 2-7 from 8-3 LAN 2-7 name 8-2 network 2-6 power 2-1 connections 2-3 connects 8-2 contents of shipment 2-1 control in 2-4 pinout 2-5 control out 2-5 controlled slip seconds 7-5 controller revision 6-3 controller board slots 7-1 controller info 7-3 control-Z 5-3 create dedicate map 8-2 creating dedicated map 8-6 dial plan 10-21 CSS 7-5 CSU status LED 4-1, 4-3 CTS chain port status 4-7 clear to s
Index complete 10-27 creating 10-21 implementing 10-25 network terminations 10-3 plan 10-23 provision network 10-23 remote access setup 10-22 sample network terminations 10-24 sample user termination 10-25 signaling 10-3 slot/port 10-3 video conferencing setup 10-22 dial plan menus 10-1 DID 10-13, 10-16 digits transferred 10-13, 10-16 prefix 10-13, 10-16 digital access cross-connect system (DACS) 1-4 direct inward dialing 10-13, 10-16 disable 13-11 disconnect 13-6 display event log 6-10 download configurat
Index TFTP server 6-14, 6-16 firmware begin update 6-15 revision 6-3 update 6-13 begin 6-15 module slot 6-14 restart schedule 6-14 TFTP 6-14, 11-1, 11-4 XMODEM 6-14, 11-1 updating 11-1 first DS0 10-9, 10-12, 10-14 flash 6-18 flash memory installed 6-3 flashing red CSU LED 4-3 flow control 4-8 configure 6-9 Force Mode 9-3 forget password 4-11 frame 7-5 frame relay description 1-2 framing errors 6-7 from configuration 8-3 from slot 8-3 front panel access active alarm display menus 4-4 activating 4-2 alarm 4-
Index insert dedicated map connection 8-3 insert password 6-11 Installation 2-1 installed memory 6-3 installing ATLAS 800 PLUS 2-1 modules 2-8 interface configuration Quad T1/PRI 10-9 Interface Configuration 9-3 interface configuration 10-7 Introduction 1-1 IP status (Telnet utility) 13-7 IP address configure 6-8 TFTP server 6-14, 6-16 IP adress SNMP 6-9 ISDN access switch description 1-5 K keyboard keys 5-3 keypad 4-4 L label password 6-11 LAN connection 2-7 Last Run Time 9-7 Last Test Status 9-7 layout
Index installed 6-3 menu alarm 4-11 configuration 4-7 module 7-2 modules 6-20 path 5-1 session 13-6 status 4-7 submenu 7-3 system status 6-3 system utility 6-13 util 4-9 menu structure, front panel 4-4 menu tree front panel main menu 4-6 menus circuit status 9-5 dedicated maps 8-1 dial plan 10-1 modules 7-1 system config 6-7 system info 6-2 system utility 6-13 method signaling 10-12 min DS0s 10-18 Min Num DS0s 9-4 modem initialize 6-9 modem initialization string 6-9 module configuration 7-5 menu 7-2 slot 7
Index 12 number to dial 10-18 number type template 10-8 numberic keypad 4-2 numbers accept 10-4, 10-6 reject 10-5, 10-7 numeric keypad 4-4 NVRAM 4-11 Nx 56/64 user termination 10-17 O Octal BRI network termination 10-18 switch type 10-20 user termination 10-20 offline 7-3 offline/no response 7-3 online 7-2, 7-3 online help 5-5 online status 4-2 operating front panel 4-1 terminal menu 5-1, 10-1 VT 100 3-4 operating ATLAS 800 PLUS 3-1 operation 3-1 operation keys 4-4 operation keys, described 4-4 option slo
Index dial plan 10-3 ethernet 2-7 ethernet status 6-5 name 7-5 configure ethernet port 6-8 speed 6-9 port name 7-5 port type configure chain port 6-9 ports available Nx 56/64 10-18 number of 10-18 power connection 2-1 power up testing 2-8 preconfigure module slots 7-2 pre-sales support C-1 previous transfer status 6-16 previous update status 6-15 PRI Quad T1/PRI 10-14 Quad T1/PRI configuration 10-9 PRI switch 10-9 primary search 10-4, 10-7 primary timing sources 6-7 print log 13-11 privileges SNMP 6-9 PRMs
Index Rx frames 6-5 S S0 system config menu 4-7 status menu 4-7 S1-S8 config menu 4-9 status menu 4-7 save configuration file 6-17 saving configuration to TFTP server 13-12 schedule restart system 6-14 secondary search 10-4, 10-7 security TFTP server 13-13 security levels 6-11 SEFS 7-5 selecting active menu 4-2 selecting front panel menu items 4-5 self test failure messages 13-1 selftest 2-8, 4-10 clear log 6-18 run 4-10, 6-17 system 6-17 view log 6-17 send configuration file 6-16 serial number 6-3 servic
Index status menu chain port status 4-7 ethernet status 4-7 S1-S8 4-7 stopping current activity 4-2 storing configuration on TFTP server 13-12 Strip MSD 10-19, 10-20 strip MSD 10-10, 10-13, 10-14, 10-17 structure front panel 4-1 terminal menu 5-1, 10-1 submenu menu 7-3 modules 7-3 subnet mask config menu 4-8 configure 6-8 support C-1 post-sales C-1 pre-sales C-1 swap ANI/DNIS 10-11, 10-15 switch parameters 10-1 switch type 10-9 Octal BRI 10-18, 10-20 Quad T1/PRI 10-14 switched call parameters 6-1 Syslog ho
Index Test Call 9-4 test jack 2-7 MON 2-7 Test Now 9-7 test pattern 7-7 error inject 7-7 test status 4-2 testing power up 2-8 TFTP delivered utility 13-10 save configuration file 6-17 security 13-13 server filename 6-14, 6-16 server IP address 6-14, 6-16 update firmware 6-13, 6-14, 11-1, 11-4 time current 6-10 restart schedule 6-15 restart system 6-14 set 6-3 time event log/time 6-4 time/date 4-9 timeout end of number 10-8 terminal session 6-8 timing source backup 6-7 primary 6-7 timing sources 6-5 tips fo
Index utility menu 4-9 V video conferencing setup with dial plan 10-22 view event log 6-10 selftest log 6-17 view error log 6-4 view history 4-12 VT 100 delivered utility 13-8 operation 3-4 W WAN overbooking description 1-5 warnings 61200226L1-1 view log 6-4 warranty C-1 window LCD 4-1 writing configuration to TFTP server 13-12 X XMODEM update firmware 6-13, 6-14, 11-1 Y yellow alarm 7-4 auto TX 7-6 enable/disable 7-6 yellow CSU LED 4-3 yellow system LED 4-3 ATLAS 800PLUS User Manual Index-13
Index Index-14 ATLAS 800PLUS User Manual 61200226L1-1
Product Support Information Presales Inquiries and Applications Support Please contact your local distributor, ADTRAN Applications Engineering, or ADTRAN Sales: Applications Engineering (800) 615-1176 Sales (800) 827-0807 Post-Sale Support Please contact your local distributor first. If your local distributor cannot help, please contact ADTRAN Technical Support and have the unit serial number available.
