Specifications

61184002L3-5B 1
Total Access OPTI-3 Controller Module
Installation and Maintenance Practice
®
Section 61184002L3-5B
Issue 2, February 2004
CLEI Code: SOI4JN3D_ _
Trademarks: Any brand names and product names included in this document are
trademarks, registered trademarks, or trade names of their respective holders.
CONTENTS
1. General .........................................................................1
2. Installation....................................................................3
3. Operation ......................................................................5
4. Menu Structure...........................................................10
5. Specifications .............................................................22
6. Maintenance ...............................................................22
7. Warranty and Customer Service ................................22
Appendix A. Total Access OPTI-3 SONET DCC
Operation ................................................ A-1
Appendix B. TL1 Commands, Responses, and
Autonomous Messages .......................... B-1
Appendix C. Total Access OPTI-3 Ordering
Information............................................. C-1
FIGURES
Figure 1. OPTI-3 Controller Module .............................1
Figure 2. OPTI-3 Rackmount Chassis............................2
Figure 3. OPTI-3 Wallmount Chassis ............................2
Figure 4. OPTI-3 RMC...................................................3
Figure 5. OPTI-3 WMC..................................................4
Figure 6. Fiber Connection to the OPTI-3 .....................4
Figure 7. OPTI-3 Menu Tree ...................................12,13
Figure 8. Status Menu...................................................18
Figure 9. OC-3 Line Loopback ....................................20
Figure 10. OC-3 Local Loopback...................................20
Figure 11. DS3 Line Loopback ......................................20
Figure 12. DS3 Local Loopback ....................................20
TABLES
Table 1. Compliance Codes ..........................................3
Table 2. Provisioning Menu Options ......................6,7,8
Table 3. OPTI-3 Front Panel LEDs ............................11
Table 4. OPTI-3 Front Panel Pushbuttons ..................11
Table 5. Alarm Codes and Descriptions .....................19
Table 6. OPTI-3 Specifications...................................23
Table B-1. TL1 Commands Corresponding to Menu
Access............................................. B-2 – B-35
Table B-2. General TL1 Commands not Corresponding
to Menu Access ........................... B-36 – B-39
Table B-3. Autonomous Alarm/Event TL1 Message
Formats and Parameters ............... B-41 – B-43
Table C-1. Available Pre-Configured OPTI-3
Systems .......................................................C-2
Figure 1. OPTI-3 Controller Module
1. GENERAL
This practice provides installation and maintenance
procedures for the Total Access
®
OPTI-3 Controller
Module (OCM), illustrated in Figure 1.
Revision History
This is the second release of this document. This
document was revised to explain modifications in the
OPTI-3 Controller Module software and provisioning
options. This I&M reflects functionality of System
Release 1.3 (Dseries) firmware. The menus and
functionality are an extension of the prior system
release (OPTI-3 System Release 1.2 - Cseries).
Dseries firmware is not compatible with System
Release 1.1 (Bseries).
Description
The Total Access OPTI-3 Controller Module, P/N
1184002L3, provides 3 electrical DS3 drops from a
single or redundant OC-3 interface when used with an
OPTI-3 chassis. The OCM front panel is shown in
Figure 1. The OCM may be installed in either a
Rackmount Chassis (RMC), P/N 1184003L1, or a
Wallmount Chassis (WMC), P/N 1184001L1.
Features
The OPTI-3 Controller Module features include the
following:
NOTE
There are two chassis that can house the OPTI-3
Controller Module, an RMC and a WMC. See
Figure 2 and Figure 3 respectively. Some of
the following features are available only when
installing the OCM in a specific chassis. If a
feature is chassis specific, it is noted.
OPTI-3
ENABLE
TESTAPS ACO
1184002L3
CRAFT
STATUS
OPTICS
DS3-1 DS3-2 DS3-3
ACO