AUTO - SCANNING WITH DIGITAL CONTROL LCD COLOR MEDICAL MONITOR AMM190WTD2 Operation Manual For future reference, record the serial number of your display monitor in the space below : Serial Number The serial number is located on the back of the monitor
Contents AMM190WTD2 Operation Manual...............................................................................1 AMM190WTD2 Gebruikershandleiding.....................................................................41 AMM190WTD2 Manuel d’exploitation.......................................................................81 AMM190WTD2 Benutzerhandbuch.......................................................................... 121 AMM190WTD2 Manuale di funzionamento............................................
AMM190WTD2 1 ENGLISH back of the monitor WARNING The title «WARNING» is used to inform the users of possible causes that could inflict the injury, death, or property damage to the patients. CAUTION The title «CAUTION» is used to inform the users of possible causes that could inflict the patients although it might not severe enough to cause deaths.
2 User’s Guide TABLE OF CONTENTS Product Description and Intended Use....................................................... 3 Warnings and Cautions.............................................................................. 4 Symbol Explanations.................................................................................. 7 EU Declaration of Conformity for Medical Applications.............................. 8 Safety Precaution............................................................................
Product Description and Intended Use Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future.
4 User’s Guide Warnings and Cautions Please read this manual and follow its instructions carefully. The words warning, caution, and note carry special meanings and should be carefully reviewed: Warning The personal safety of the patient or physician may be involved. Disregarding this information could result in injury to the patient or physician. Caution Special service procedures or precautions must be followed to avoid damaging the instrument.
1. Read the operating manual thoroughly and be familiar with its contents prior to using this equipment. 2. Carefully unpack the unit and check if any damage occurred during shipment. 3. Should any solid object or liquid fall into the panel, unplug the unit and have it checked by qualified personnel before operating it any further. 4. Uplug the unit if it is not to be used for an extended period of time. To disconnect the cord, pull it out by the plug. Never pull the cord itself. 5.
6 User’s Guide Cautions 1. The AC Adapter must be plugged into a Grounded power outlet. 2. Use only the proprietary AMM190WTD2 power supply for the AMM190WTD2 monitor. Make a proper connection by ensuring that the shrink tubing completely secures the connection between the DC power cord and the extension cord. 3. Turn power off when unit is not in use. 4. Never operate the unit right after having transported from a cold location directly to a warm location. 5.
Dangerous: High Voltage Direct Current Serial Number This way up Fragile, handle with care Stacking limit by number Keep dry Recyclable Consult accompanying documents. Indicates proof of conformity to applicable European Economic Community Council directives and to harmonized standards published in the official journal of the European Communities. Authorized Representative in Europe Indicates protective earth ground. For indoor use only.
8 User’s Guide EU Declaration of Conformity for Medical Applications A Declaration of Conformity has been filed for this product. A sample of this document may be found in the addendum which accompanied this manual. For a copy of the Declaration of Conformity document, please contact ADVAN Int’l Corp. and request for AMM190WTD2 DOC. Prepare for Unpack Before you unpack your monitor, prepare a suitable workspace.
· · · · · · Avoid placing the monitor, or any other heavy object, on the power cord to prevent fire or electrical shock from damage to the power cord. Do not expose the monitor to rain, excessive moisture, or dust to avoid fire or shock hazard. Do not cover the slots or openings of the monitor for proper heat dissipation. Always put the monitor in a place where there is adequate ventilation.
10 User’s Guide POWER MANAGEMENT FUNCTION The monitor is equipped with the power management function which automatically reduce the power consumption when not in use in three power level modes. • Stand-by Mode The monitor goes into stand-by mode when the horizontal sync signal is off for about 10 seconds. In this mode, the screen goes off and the power LED blinks for 1 seconds On and 1 second Off. The screen is displayed after the horizontal sync signal is restored.
AMM190WTD2 11 ENGLISH PRESET MODES DVI and VGA input signal formats Resolution Horizontal frequency ( KHz ) Vertical frequency ( Hz ) Pixel clock ( MHz ) 640 x 350 @70Hz 31.469 70.087 25.175 640 x 480 @60Hz 31.469 59.940 25.175 640 x 480 @75Hz 37.500 75.000 31.500 640 x 480 @85Hz 43.269 85.008 36.000 800 x 600 @56Hz 35.156 56.250 36.000 800 x 600 @60Hz 37.879 60.317 40.000 800 x 600 @72Hz 48.077 72.188 50.000 800 x 600 @75Hz 46.875 75.000 49.500 800 x 600 @85Hz 53.
12 User’s Guide Video Signals Format DVI VGA /SOG Video Y/C NTSC -M NTSC-443 O O PAL-BDGHI PAL-M PAL-N PAL-60 O O 480/59.94i O SDI 1/2 O 480/59.94p 576/50i O O Component Y/Pb /Pr RGB +CS RGB +HV O O O O O O O O O O O O 576/50p O O 720/50p O O O O O O 720/59.94p O O O O O O 720/60p O O O O O O 1035/59.94i O O O O O 1035/60i O O O O O 1080/23.98psf O O O O O 1080/24psf O O O O O 1080/23.
AMM190WTD2 13 ENGLISH PIP / POP / PBP function The following combination options are available to you: VGA DVI SDI1 SDI2 C-Video Y-C Component / RGBs VGA O O O O O O O DVI O O O O O O O O SDI1 O O O O O O O SDI2 O O O O O O O C-Video O O O O O O O Y-C O O O O O O O O Component / RGBs O O O O O O O O O O O O O O Main SOG PIP SOG
14 User’s Guide Monitor input signals and function items Component RGB SDI SOG C/S Video SD HD SD HD SD HD Brightness O O O O O O O Contrast O O O O O O Phase O Chroma O VGA DVI O O O O O O O H/V Sharpness O O O O O O O O O O Scale Mode O O O O O O O O O O O O O O Color Space Zoom / Pan O O O O O O O O O O Multi Display O O O O O O O O O O H/V Position O O Freqency Phase O O O Noise Reduction O O O O O O O
DDC To make your installation easier, the monitor is able to Plug and Play with your system if your system also supports DDC protocol. The DDC (Display Data Channel) is a communication protocol through which the monitor automatically informs the host system about its capabilities, for example, supported resolutions and corresponding timing. The monitor supports DDC1 and DDC2B standard. INSTALLATION To install the monitor to your host system, please follow the steps as given below: Steps 1.
16 User’s Guide CONNECTING the POWER CORD * C heck first to make sure that the power cord you use is the correct type required for your area. * T his monitor has an universal AC adapter that allows operation in either AC 100 - 240 V ac voltage area. No user-adjustment is required. * Plug one end of the power cord to the AC adapter, plug another end to a proper AC outlet. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed and marked HAR.
Key Name and Function Power LED : Lights up to indicate the power is turned ON. Power Switch : To power ON or OFF the monitor. Rotary switch : With the OSD menu activated, increases the value of the selected (Ture Right) parameter or moves rightward in OSD menu. Rotary switch : With the OSD menu activated, increases the value of the selected (Ture Left) parameter or moves leftward in OSD menu. PIP Switch : To enable or disable Picture In Picture function.
18 User’s Guide OSD Section Main Menu Chromatic Adjust Color Temp, Gamma Visual Adjust Brightness, Contrast, Phase, Chroma, Sharpness-H, Sharpness-V Setting Adjust Scale Mode, Color Space, Mirror, Freeze Frame, Zoom / Pan, PIP, POP, PBP Advanced Adjust OSD Position Control, Screen Control, DPMS, Auto Source Select, Smart Select, Restore Factory, Key Lock Information Adjust Custom Entry, SN, Run Time, Input Format Exit Exit the menu
AMM190WTD2 19 ENGLISH OSD Section Chromatic Color Temp Change the color temperature - D65, D93, S1, S2 Gamma Change the gamma value - 1.8, 1.9, 1.95, 2.1, 2.1S, 2.2, 2.3, 2.4, 2.
20 User’s Guide OSD Section Setting Scale Mode Change the scale mode - Fill all, One to One, Vertical - fill, Horizontal - fill, Fill aspect ratio Color Space Change color space between RGB and YPbPr *available for Component and RGBS Mirror Off / On mirror image Freeze Frame Off / On freeze frame Zoom / Pan Enable zoom - in and pan function PIP Enable PIP (Picture In Picture) function POP Enable POP (Picture On Picture) function PBP Enable PBP (Picture By Picture) function Exi
AMM190WTD2 21 ENGLISH OSD Section Sub menu of PIP Mode PIP Mode ON / Off Source PIP sub screen source - SDI1,2, C-Video, S-Video, Component, VGA, DVI, SOG Position PIP sub screen position - Top L, Top R, Bottom L, Bottom R Size PIP sub screen size - Small, Medium, Large Blending PIP sub screen blending (Range 0 - 100) Swap PIP sub screen swap Exit Exit the menu Sub menu of PBP Mode PBP Mode ON / Off Source PBP sub screen source - SDI1,2, C-Video, S-Video, Compone
22 User’s Guide OSD Section Sub menu of POP Mode POP Mode ON / Off Source POP sub screen source - SDI1,2, C-Video, S-Video, Component, VGA, DVI, SOG Position POP sub screen position - Top L, Top R, Bottom L, Bottom R Size POP sub screen size - Small, Medium, Large, Full Blending POP sub screen blending (Range 0 - 100) Swap POP sub screen swap Exit Exit the menu
AMM190WTD2 23 ENGLISH OSD Section Advanced OSD Position Change the OSD menu - Position, Background, Control OSD time out, Language Screen Control Control and adjust H and V position, Freqency, Phase Noise Reduction, Motion Offset DPMS Change the DPMS Auto Source Adjust Auto Source Select between on and off Select Smart Select Enable / Disable smart select sub menu Restore Factory Changes the all OSD value to factory outgoing status Key Lock Set to key lock mode Overscan Adjust
24 User’s Guide OSD Section Sub menu of OSD Control H-position Adjust OSD H - position (Range 0 - 100) V-position Adjust OSD V - position (Range 0 - 100) Back ground Adjust transparency of OSD back ground (Range 0 - 100) OSD Time out Adjust OSD time out - 5s, 10s, 15s, 20s, 1m, 2m Language OSD language - English, Japanese, Chinese, Korean, French, German Exit Exit the menu Sub menu of Screen Control H-position Adjust screen H - position (Range 0 - 100) *available for VGA V-position
AMM190WTD2 25 ENGLISH OSD Section Information Custom Entry Change the user or monitor’s name SN Display the serial number Run Time Display the total run time Input Format Display the current input resolution and vertical frequency Exit Exit the menu
26 User’s Guide TROUBLESHOOTING Before sending your LCD monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem. Problems Current Status Remedy No Picture LED ON · Using OSD, adjust brightness and contrast to maximum or reset to their default settings. LED OFF · Check the Locker switch and Power switch. · Check if AC power cord is properly connected to the AC adapter.
Model LCD Panel Type Resolution Pixel Pitch Display Color Color Tone Response Time Face Finishing Viewing Angle Input Signal Composite Y/C RGB/Component AMM190WTD2 19 TFT LCD Panel Active Matrix 1680 x 1050 @ 60Hz 0.243575 X 0.24375 mm 16.7M colors Up to 256 color tone <25ms Typ. Protective Filter with Anti-Reflected Hard Coated +/- 85°(Horizontal), +/- 85° (vertical) 1.0Vp-p Y : 1.0± 0.1Vp-p, C : 0.3± 0.03Vp-p RGB : 0.7 ± 0.1 Vp-p, Composite Sync : 0.3Vp-p ~ 5Vp-p, H/V Sync : TTL Level Component : 0.
28 User’s Guide : Direct Current 51LJ Medical Equipment E215822 MEDICAL EQUIPMENT WITH RESPECT TO ELECTRIC SHOCK, FIRE AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL 60601-1, AND CAN/CSA C22.2 NO. 601.1 : UL approval mark according to the safety standard for Medical equipment This monitor is intended for use in Health Care Facilities model AMM190WTD2 Equipment is not suitable for use in the presence of flammable anesthetic mixture with air or with oxygen or nitrous oxide.
Electromagnetic Compatibility Like other electrical medical equipment, the AMM190WTD2 requires special precautions to ensure electromagnetic compatibility with other electrical medical devices. To ensure electromagnetic compatibility (EMC), the AMM190WTD2 must be installed and operated according to the EMC information provided in this manual. Note The AMM190WTD2 has been designed and tested to comply with IEC 60601-1-2:2001 requirements for EMC with other devices.
30 User’s Guide Power frequency (50/60Hz) magnetic field IEC 61000-4-8 Voltage dips, short interruptions and voltage variations on power supply input lines IEC61000-4-11 3.0 A/m Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment. 3.0 A/m <5% Ut (>95% dip in Ut) for 0.5 cycle <5% Ut (>95% dip in Ut) for 0.
Recommended Separation Distances Between Portable and Mobile RF Communications Equipement and the AMM190WTD2 System The AMM190WTD2 system is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
32 User’s Guide Dimension Drawing (mm) of AMM190WTD2 REAR VIEW
AMM190WTD2 33 ENGLISH Connectors DC Input Connector Jack Power Input Pin Description Pin Description 1 GND 3 VCC_18V 2 GND 4 VCC_18V Video Input 24 pin DVI-I connector. DDWG or equivalent connector. Pin Description Pin Description Pin Description 1 T.M.D.S. Data2- 11 T.M.D.S. Data1 Shield 21 NC 2 T.M.D.S. Data2+ 12 NC 22 T.M.D.S. Clock Shield 3 T.M.D.S. Data2 Shield 13 NC 23 T.M.D.S. Clock+ 4 NC 14 +5V Power 24 T.M.D.S.
34 User’s Guide Description of Warranty ADVAN warrants to the first Buyer (Buyer) that the product purchased when shipped in its original container will conform to ADVAN specifications, and to any ADVAN approved specifications furnished to ADVAN by the Buyer, and will be free of defects in materials and workmanship. ADVAN warrants that the product purchased is manufactured from new components which meet ADVAN standards, quality and specifications.
Return Material Authorization (RMA) Procedure All claims must be submitted through the ADVAN website, whether in warranty or out, first Buyer, distributor or OEM. End Users who have purchased through a distributor or OEM, please contact the distributor or OEM. http://www.advancorprma.com Follow the instructions to receive an RMA number, shipping instructions and a shipping label to be placed on the outside of the shipping container. A serial number and a detailed reason for return are required.
36 User’s Guide Out-of-Warranty ADVAN or its ASC will repair or replace if defective in material or workmanship with fee, any product which the warranty period has expired (out-of-warranty). Buyer must notify ADVAN or its ASC of the defect and request an RMA number. If the configuration has been modified in any manner, the product must be returned to its original configuration before any service will be performed by ADVAN or its ASC.
Disclaimer THE FORGOING IS THE COMPLETE WARRANTY FOR ADVAN PRODUCTS AND SUPERSEDES ALL OTHER WARRANTIES AND REPRESENTATIONS, WHETHER ORAL OR WRITTEN.
正規代理店 株式会社 ナナオ 〒924-8566 石川県白山市下柏野町153番地 電話：076-275-4121 Fax：076-275-4125 Web サイト：http://www.radiforce.com Authorized Representative in Europe and Exclusive Distributor EIZO GmbH, Display Technologies Siemensallee 84, D-76187 Karlsruhe, Germany Tel: +49 721 20321 0 Fax: +49 721 20321 474 Web Page : http://www.eizo.eu Distributor ADVAN Korea 150-871 서울시 영등포구 여의도동 14-24 삼보호정빌딩 2층 210호 Tel : 02.783.5197 Fax : 02.783.5196 Web Page : http://www.advancorp.com Manufacture ADVAN INT’L CORP 47817 Fremont Blvd.
