MAA-1000 Audiophile mono power amplifier Amplificateur de puissance mono audiophile Owner’s manual Mode d’emploi FRANCE
RECYCLING IN EUROPEAN UNION COUNTRIES Disposal of your old appliance English This symbol on the product or on its packaging means that your electrical and electronic equipment should be disposed at the end of life separately from your household wastes. There are separate coilection systems for recycling in EU. For more information, please contact the local authority or the dealer where you purchased the product.
WARNING ATTENTION ATTENTION: afin de réduire tout risques de chocs électriques ou de feu, ne pas exposer votre appareil à l’humidité ou à toutes sortes de liquides WARNING: to reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. AVERTISSEMENT Pour prévenir tout risques de chocs électriques, ne pas ouvrir l’appareil. Si un problème apparait, faites réparer votre appareil par un technicien qualifié.
CONSIGNES DE SECURITE LIRE LES INSTRUCTIONS PROTECTION DU CORDON SECTEUR Toutes les consignes de sécurité et instructions quand à l’utilisation de notre produit doivent faire l’objet d’une lecture attentive. Votre cordon d’alimentation doit être correctement installée afin qu’il ne soit pas piétiner ou arracher.
SAFETY INSTRUCTIONS READ INSTRUCTIONS POWER-CORD PROTECTION All the safety and operating instructions should be read before the appliance is operated. Power-supply cords should be routed so that they are not likely to be walked on or pinched by paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. RETAIN INSTRUCTIONS The safety anil operating instructions should be retained for future use.
WARNING ATTENTION No good Good Your product is designed to be placed on a firm and level surface. Don’t place the unit sideways, a big power exerts on the single side of the plate. With this power, the plate will be broken easily. Please see the picture. Votre produit a été conçu pour être installé sur une surface plate et rigide. Ne poser pas votre appareil de travers car vous risqueriez de casser ses pieds. Chaque pied est constitué d’une pointe de découplage fixée sur une coupelle métallique.
RÉGLAGES FACE AVANT FRONT PANEL CONTROLS BOUTON STANDBY/ON Appuyez sur ce bouton pour mettre en marche votre appareil (éclairage bleu de votre bouton après sa temporisation). La mise en marche de votre appareil ne peut se faire que si le bouton Marche/Arrêt général situé sur la face arrière est en position ON. En mode STANDBY, l’alimentation principale est coupée à l’exception du micro-contrôleur servant à activer l’état de veille de l’appareil. Le bouton est allumé en rouge.
METERS They displays the peak power level into an 8 ohms load. Also, they integrate the signal over a short enough time to give an accurate representation of the average power. POINTES DE DÉCOUPLAGE Votre amplificateur est équipé de pointes de découplage, il est livré avec des coupelles antidérapantes. A installer comme indiqué sur la photo. ISOLATING SPIKES Your amplifier used spike-feet, you need to use them with non-skid cupels included.
RÉGLAGES & CONNEXIONS FACE ARRIÈRE REAR PANEL CONNECTIONS & CONTROLS PRISE D’ALIMENTATION /INTERRUPTEUR GÉNÉRAL / SÉLECTEUR DE TENSION Pour alimenter votre appareil, commuter l’interrupteur général sur ON et vérifier la tension d’alimentation. Si votre tension est de 115V vous devez changer les fusibles avec ceux fournis. POWER CORD /MASTER ON/OFF SWITCH / VOLTAGE SELECTOR Before plugging in the amplifier, its master power switch must be in the OFF position.
SPEAKER TERMINALS Connect cables between speakers and your amplifier.
ment important, aussi votre amplificateur doit rester correctement ventilé. HIGH BIAS SELECTOR By switching the High Bias mode in ON mode, your amplifier will be similar as a Class’A amplifier of the first watts of use. In this mode, the temperature of your amplifier will be important, also, it’s important that there should be enough clear space around the amplifier to permit a free flow of air.
SPECIFICATIONS ET PERFORMANCES PERFORMANCE SPECIFICATIONS POWER OUTPUT 6Ω ≥450W FREQUENCY RESPONSE 10Hz-120kHz DISTORSION ≤ 0,05% S/N RATIO ≥ 115 dB INPUT IMPEDANCE UNBALANCED 20KΩ INPUT IMPEDANCE BALANCED 16KΩ AC INPUT 110-230V POWER CONSUMPTION S/BY OFF POWER CONSUMPTION S/BY ON POWER CONSUMPTION MAX < 600W TRANSFORMER(S) 1 DIMENSIONS (cm) H.24x l.44x D.
FRANCE w w w. a d v a n c e - a c o u s t i c .