Manual

ManualsBrandsAdvance Adapters ManualsCar50-1400

KIT CONSISTS OF:

No. Qty Part No. Description

ADVANCE ADAPTERS INC. P/N: 50-1400

P.O. Box 247, 4320 Aerotech Center Way Old Part No: 711014

Paso Robles, CA 93447 PAGE 1 OF 3

Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 06-06-14

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will

void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend

that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that

a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at

automotive dealerships and parts stores.

OPTIONAL ITEMS:

Qty Part No. Description

1 716003 CROSSMEMBER

1 716302 SEALED BEARING

1 716001 (T86) LARGE HOLE OR

1 716002 (T90) SMALL HOLE

BEARING RETAINER

NOTE: Two TH400 bolt patterns have been drilled

into this housing; one is for a GM TH400 and the

other is rotated for the AMC TH400.

1. 1 51-0600 ADAPTER CASTING (Ref: 711106)

2. 1 52-1300 SPUD SHAFT (6-Splines)(Ref: 711313)

3. 1 *52-1401 29TH x 6SPL. 2.46: INPUT GEAR

4. 1 52-3200 OUTPUT SHAFT (Ref: 711332)

5. 1 716308 BEARING (#6209)

6. 1 716450 SNAP RING (GM #378-5205)

7. 1 716510 GASKET (GM #862-4709)

8. 1 716568 GASKET

9. 1 716707 SEAL (NAT. #472144)

10. 6 723701 HEX NUT

11. 11 723704 3/8" LOCKWASHER

12. 6 723711 3/8"-16 x 2" STUD BOLTS

13. 5 723723 3/8"-16 x 1-1/2" H.H.C.S. (T/C BOLTS)

14. 1 728701 NYLON LOCK NUT

*20 Degree pressure angle gear:

Model 18 transfer cases with 2.46:1,

w/ T14 transmission, 1 ¼” intermediate shaft

CJ with Buck V6 (68-71)

Drive gear# 18-8-50 (947382) ---29 tooth x 10 spline

Intermediate Gear # 18-5-9 (809293) ---39 tooth x 18 tooth

**Requires AA part # 52-1401

18-8-23 (809297) ----29 tooth x 6 spline (SUPPLIED IN KIT)

17 Degree pressure angle gear:

Model 18 transfer cases with 2.03:1,

w/ T14 transmission, 1 ¼” intermediate shaft

Jeepster/CJ (67-74) models 18/20

Drive gear# 18-8-49 (947339) ---26thx10sp.

Intermediate Gear# 18-5-16(946786) 34thx20th

(Special order gear)

TURBO 400 TO JEEP VEHICLES

DANA 18/20 TRANSFER CASE

Summary of content (3 pages)

PAGE 1
ADVANCE ADAPTERS INC. P/N: 50-1400 P.O. Box 247, 4320 Aerotech Center Way Paso Robles, CA 93447 Telephone: (800) 350-2223 Fax: (805) 238-4201 Old Part No: 711014 PAGE 1 OF 3 Page Rev. Date: 06-06-14 TURBO 400 TO JEEP VEHICLES DANA 18/20 TRANSFER CASE KIT CONSISTS OF: OPTIONAL ITEMS: No. Qty Part No. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14.
PAGE 2
ADVANCE ADAPTERS INC. P/N: 50-1400 P.O. Box 247, 4320 Aerotech Center Way Paso Robles, CA 93447 Telephone: (800) 350-2223 Fax: (805) 238-4201 Old Part No: 711014 PAGE 2 OF 3 Page Rev. Date: 06-06-14 TURBO 400 TO JEEP VEHICLES DANA 18/20 TRANSFER CASE GM TURBO 400 3 SPEED AUTOMATIC The GM TH400 has a case length of 24-1/4", 13 bolts for holding the oil pan in position and is available in 3 different engine to transmission bolt patterns.
PAGE 3
ADVANCE ADAPTERS INC. P/N: 50-1400 P.O. Box 247, 4320 Aerotech Center Way Paso Robles, CA 93447 Telephone: (800) 350-2223 Fax: (805) 238-4201 Old Part No: 711014 PAGE 3 OF 3 Page Rev. Date: 06-06-14 TURBO 400 TO JEEP VEHICLES DANA 18/20 TRANSFER CASE SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void any possible warranty or return privileges.