Owner manual

ManualsBrandsAdvance Adapters ManualsCar50-8902

KIT CONSISTS OF:

No. Qty Part No. Description

ADVANCE ADAPTERS INC. P/N: 50-8902

P.O. Box 247, 4320 Aerotech Center Way Old Part No: 711089-16

Paso Robles, CA 93447 PAGE 1 OF 4

Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 06-02-10

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will

void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend

that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that

a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at

automotive dealerships and parts stores.

OPTIONAL ITEMS:

Qty Part No. Description

1. 1 51-7300 CASTING (Ref: 711173)

2. 1 51-8500 ADAPTER HOUSING (Ref: 711185)

3. 1 52-1600 SHAFT (Ref: 711316)

4. 1 52-8900 700R-4 OUTPUT SHAFT (Ref: 711389)

5. 1 Pack 714203 BOLT PACK (50-7300)

6. 1 715521-BLK T/C SHIFTER LINKAGE BRKT.

7. 1 716082 700R PLASTIC WASHER

8. 1 716301 BEARING

9. 1 716507 T/C GASKET

10. 2 716511 "O"-RING

11. 4 720015 METRIC WASHER

12. 4 720047 H.H.C.S. 10mm X 1.5 X 70mm LG.

13. 1 728701 NUT

14. 1 728702 7/8" FLAT WASHER

15. 1 TLC001 LAND CRUISER INSTRUCTION MANUAL

1 716004 CROSSMEMBER ASSY

(Includes #716003 Mount)

GM 700R-4 AUTOMATIC OVERDRIVE TO

LAND CRUISERS 1974-AUGUST 1980 (4 SPEED)

NOTE: This kit requires the 2WD output shaft

to be shortened. If you are using this kit on a

newer hex bolt pattern 4L60E transmission, then

you will be required to use our 51-0405 adapter

housing. Please note that the cut off location on

the output shaft must be made after this adapter

is installed on the transmission. This 51-0405

adapter make the hex pattern 4L60E transmission

look just like the square bolt pattern transmis-

sion, and the cut off location for the output shaft

is shown on this instruction sheet is for the square

bolt pattern transmission.

Summary of content (4 pages)

PAGE 1
ADVANCE ADAPTERS INC. P/N: 50-8902 P.O. Box 247, 4320 Aerotech Center Way Paso Robles, CA 93447 Telephone: (800) 350-2223 Fax: (805) 238-4201 Old Part No: 711089-16 PAGE 1 OF 4 Page Rev. Date: 06-02-10 GM 700R-4 AUTOMATIC OVERDRIVE TO LAND CRUISERS 1974-AUGUST 1980 (4 SPEED) KIT CONSISTS OF: OPTIONAL ITEMS: No. Qty Part No. Description 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
PAGE 2
ADVANCE ADAPTERS INC. P/N: 50-8902 P.O. Box 247, 4320 Aerotech Center Way Paso Robles, CA 93447 Telephone: (800) 350-2223 Fax: (805) 238-4201 Old Part No: 711089-16 PAGE 2 OF 4 Page Rev. Date: 07-19-13 GM 700R-4 AUTOMATIC OVERDRIVE TO LAND CRUISERS 1974-AUGUST 1980 (4 SPEED) INSTALLATION INSTRUCTIONS This kit is for the GM 700R-4 4 speed automatics to all Toyota Land Cruiser transfer cases, 1974 through August 1980. The design of this kit is based off of a 2WD 700R4.
PAGE 3
ADVANCE ADAPTERS INC. P/N: 50-8902 P.O. Box 247, 4320 Aerotech Center Way Paso Robles, CA 93447 Telephone: (800) 350-2223 Fax: (805) 238-4201 Old Part No: 711089-16 PAGE 3 OF 4 Page Rev. Date: 07-12-01 GM 700R-4 AUTOMATIC OVERDRIVE TO LAND CRUISERS 1974-AUGUST 1980 (4 SPEED) SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void any possible warranty or return privileges.
PAGE 4
ADVANCE ADAPTERS INC. P/N: 50-8902 P.O. Box 247, 4320 Aerotech Center Way Paso Robles, CA 93447 Telephone: (800) 350-2223 Fax: (805) 238-4201 Old Part No: 711089-16 PAGE 4 OF 4 Page Rev. Date: 07-26-00 GM 700R-4 AUTOMATIC OVERDRIVE TO LAND CRUISERS 1974-AUGUST 1980 (4 SPEED) P/N 715521-BLK Installation Instructions: The difference between the 3 and 4 speed linkage is exactly 2". The linkage gate will need to be welded or bolted to the our bracket.