Manual

ManualsBrandsAdvance Adapters ManualsCar713111

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the components will void

any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion, we strongly recommend that

you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter components. We recommend that a service

manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment. These manuals are normally available at automotive dealerships

and parts stores.

KIT CONSISTS OF:

No. Qty Part No. Description

ADVANCE ADAPTERS INC. P/N: 713111

P.O. Box 247, 4320 Aerotech Center Way

Paso Robles, CA 93447 PAGE 1 OF 2

Telephone: (800) 350-2223 Fax: (805) 238-4201 Page Rev. Date: 08-16-00

1. 1 713111-L DRIVER'S SIDE ENGINE MOUNT

2. 1 713111-R PASSENGER SIDE ENGINE MOUNT

3. 1 714200 BOLT PACK

4. 1 GM001 GM INSTRUCTION MANUAL

INSTALLATION PROCEDURES:

These engine mounts are designed to bolt over the original S10 2.8 V6 engine rubbers. When used with the TH350

transmission or the original T4/T5 manual transmission, driveshaft modifications will not be required. The engine

mounts work best by first installing the welded mounts over the V6 rubbers. Install the special 7/16" hex head bolt

through the rubber and into the Advance Adapter support. Once the mounts are in position, the engine can then be

positioned into the chassis for final assembly.

The engine mounts have two different engine position locations. The Advance Adapters brackets have two hole locations

for the special 7/16" bolt. The upper hole will position the engine approximately 1" higher than the lower hole. The height

will make a significant difference in your exhaust system requirements. We suggest that you trial fit the engine mounts

to determine your best choice. Lower locations are usually required on vehicles that have been lowered. Advance

Adapters recommends using the upper location whenever possible. If you select the lower location, the engine mounts

will need to be modified for the additional clearance and the upper hole will need to be removed.

LOWER ENGINE POSITION:

Optional stock manifolds that fit late model engines only

Modification for starter motor clearance over engine support is necessary

Modification to the engine mounts for the removal of the upper hole

Slick Fit Headers are not available.

UPPER ENGINE POSITION:

Advance Adapter "Slick Fit" header No. 717052

Stock Manifolds (1987 & newer Low Performance car)

No modifications to the engine mounts

CHEVY V8 ENGINE TO S10-S15 2WD

NOTE: You may need to grind the small metal tabs located on both sides on your stock 2.8 liter V6

rubber mounts. This may be required to fit the Advance Adapter engine mounts over your

stock rubber mounts.

Summary of content (2 pages)

PAGE 1
ADVANCE ADAPTERS INC. P/N: 713111 P.O. Box 247, 4320 Aerotech Center Way Paso Robles, CA 93447 Telephone: (800) 350-2223 Fax: (805) 238-4201 PAGE 1 OF 2 Page Rev. Date: 08-16-00 CHEVY V8 ENGINE TO S10-S15 2WD KIT CONSISTS OF: No. Qty Part No. Description 1. 2. 3. 4. DRIVER'S SIDE ENGINE MOUNT PASSENGER SIDE ENGINE MOUNT BOLT PACK GM INSTRUCTION MANUAL 1 1 1 1 713111-L 713111-R 714200 GM001 INSTALLATION PROCEDURES: These engine mounts are designed to bolt over the original S10 2.
PAGE 2
ADVANCE ADAPTERS INC. P/N: 713111 P.O. Box 247, 4320 Aerotech Center Way Paso Robles, CA 93447 Telephone: (800) 350-2223 Fax: (805) 238-4201 PAGE 2 OF 2 Page Rev. Date: 09-19-02 CHEVY V8 ENGINE TO S10-S15 2WD NOTE: If you are using a late model block that utilizes an engine block sensor, you will need to purchase a Brass Street Elbow Dorman, Part #490-117. This will allow you to retainer your sensor in the original location in order for the block to operate correctly.