Instruction Manual

ManualsBrandsAdvance Adapters ManualsCarKJ09156BK1

TOOLS NEEDED

• Metric tools

• Floor jack

• Jack stand (s) 4

• Wheel chocks

• Drill and 3/8 bit

BILL OF MATERIALS

Part # Description Qty

M20300

3” FT spacers 2

M20301

3” Rear spacers 2

BU76123

hardware 1

M20066

Ft bump ext 2

M20333

Rear bump ext 2

S11090

Sway Bar Drop

brackets

KU01009

Ft shocks 2

KU01010

Rear shocks 2

P11183

Loctite 1

S20370

Rear track bar

bracket

Other Jeep JK Products

• KJ09145BK Hood Wranglers

• KJ09144BK Tailgate Bumpstops

• KJ71020 Upper dash panel

• KJ71030 Lower switch panel

• KU70034 Ft lower control arms

• KU70033 Rear upper control arms

• KU70037 Rear lower control arms

• KU70091 poly flex tool

• KU11005 Poly lube gun

BOM FOR 3/4 KIT

KJ09153

2007 to Current Jeep JK 3” lift with shocks

www.Daystarweb.com

Tech Support Contact Info

Tech@DaystarWeb.com

Phone: 623.907.0081

Fax: 623.907.0088

841 South 71

Avenue

Instruction Sheet P20372

2010 Daystar Products International Inc.

Hells gate, Moab UT

Summary of content (6 pages)

PAGE 1
TOOLS NEEDED • • • • • Metric tools Floor jack Jack stand (s) 4 Wheel chocks Drill and 3/8 bit Other Jeep JK Products • • • • • • • • • KJ09145BK Hood Wranglers KJ09144BK Tailgate Bumpstops KJ71020 Upper dash panel KJ71030 Lower switch panel KU70034 Ft lower control arms KU70033 Rear upper control arms KU70037 Rear lower control arms KU70091 poly flex tool KU11005 Poly lube gun BILL OF MATERIALS BOM FOR 3/4 KIT Part # Description Qty M20300 3” FT spacers 2 M20301 3” Rear spacers 2 BU76123 hard
PAGE 2
Thank you for choosing Daystar Products Daystar recommends a certified technician install this system . In addition to these instructions, professional knowledge of disassemble/reassembly procedures as well as post instructions checks must be known. Attempts to install this system without this knowledge and expertise may jeopardize the integrity and/or operating of the vehicle. Please read all the instructions before beginning the installation. Check the kit hardware against the parts list.
PAGE 3
Installation steps 20. Remove the stock bump stops and install the bump stop extenders, then install the stock bump stop into the extender as done on the front installation. 1. Jack up the front of the vehicle and support the vehicle at the frame with jack stands. Put wheel chocks behind the rear tires. 2. With the jack under the front axle, jack up the axle to remove the driver side and the passenger side wheels and disconnect the sway bar end link on the driver side then the passenger side. 21.
PAGE 4
3. 4. Disconnect the ABS line form the bracket on the steering knuckle on the driver side then the passenger side. Remove the factory shocks. With the shocks removed , sway bar end links, and ABS line disconnected, lower the axle down to remove the coil springs on the driver side first then the passenger side. 16. After drilling the 2 holes place the track bar bracket on the axle. 17. Install the supplied sleeve and stock track bar bolt in the lower mounting hole. Sleeve 18.
PAGE 5
. 15. After marking the holes, remove the bracket from the axle and drill the 2 3/8 holes. 6. With the coil spring removed install the daystar lift spacer over the stock spring isolator. Pry out the factory bump stops and install the supplied bump stop extenders in the factory cups. Then install the factory bump stops in the lower end of the extenders. It may be necessary to lubricate the bump stops to fully seat them in the extenders. 7.
PAGE 6
10. Install the front wheels and lower the vehicle to the floor. 11. Place the wheel chocks at the front wheels and jack up the rear sus- pension. Support the vehicle at the frame and remove the rear tires. 12. With the jack under the rear axle, raise the axle so you can remove the rear shocks. Disconnect rear sway bar at the frame. Also unbolt the bracket that holds the brake line to the frame. 13. Remove the rear track bar at the axle end. 14. Place the new rear track bar bracket on the rear axle.