Manual

SPECIAL NOTE: The components packaged in this kit have been assembled and machined for specific type of conversions. Modifications to any of the
components will void any possible warranty or return privileges. If you do not fully understand modifications or changes that will be required to complete your conversion,
we strongly recommend that you contact our sales department for more information. This instruction sheet is only to be used for the assembly of Advance Adapter
components. We recommend that a service manual pertaining to your vehicle be obtained for specific torque values, wiring diagrams and other related equipment.
These manuals are normally available at automotive dealerships and parts stores.
ADVANCE ADAPTERS INC. P/N: Orion
PAGE 12 OF 15
Page Rev. Date: 04-18-05
Case Schematic Index:
C1 CASE COVER NO.2
C2 GASKET
C3 GASKET
C4 OUTPUT SHAFT REAR BRG. RETAINER
C5 OIL SEAL
C6 SHIM (4 SPEED)
C7 WASHER (4 SPEED)
C8 NUT (4 SPEED)
C9 WASHER (3 SPEED)
C10 NUT (3 SPEED)
C11 COTTER PIN (3 SPEED)
C12 GASKET
C13 CASE COVER
C14 SEAL
C15 GASKET
C16 POWER TAKE OFF COVER
C17 CASE PLUG
C18 SEAL
C19 GASKET
C20 NUT (4 SPEED)
C21 WASHER (4 SPEED)
C22 SHIM (4 SPEED)
C23 COTTER PIN (3 SPEED)
C24 NUT (3 SPEED)
C25 WASHER (3 SPEED)
C26 SEAL
C27 GASKET
C28 EXTENSION HOUSING
C29 GASKET
C30 ORION CASE
Gear Schematic Index:
G1 INPUT GEAR STOPPER (4 SPEED)
G2 INPUT GEAR
G3 P.T.O. GEAR / SPACER
G4 BEARING
G5 INPUT SHAFT SPACER
G6 WASHER INPUT
G7 INPUT SHAFT LOCK NUT
G8 THRUST WASHER
G9 NEEDLE ROLLER BEARING - IDLER
G10 SPACER
G11 IDLER GEAR
G12 IDLER GEAR SPACER (UP TO APRIL OF 1975)
G13 IDLER SHAFT
G14 O-RING (2)
G15 LOCK PLATE ASSY. (IDLER)
G16 SNAP RING
G17 BALL BEARING
G18 FRONT OUTPUT SHAFT
G19 NEEDLE ROLLER BEARING
G20 FRONT DRIVE CLUTCH SLEEVE
G21 FRONT TAPERED ROLLER BEARING CUP & CONE
G22 THRUST WASHER
G23 HIGH SPEED GEAR BUSHING (INSTALLED IN GEAR)
G24 HIGH SPEED GEAR
G25 REAR OUTPUT SHAFT
G26 HI / LOW CLUTCH SLEEVE
G27 LOW SPEED GEAR BUSHING (INSTALLED IN GEAR)
G28 LOW SPEED GEAR
G29 THRUST WASHER
G30 REAR TAPERED ROLLER BEARING CUP & CONE
G31 ADJUSTING SHIMS
G32 SPACER (SPEEDOMETER)
G33 SPEEDOMETER DRIVE GEAR
Shifter Schematic Index:
S1 HI & LOW SHIFT FORK SHAFT
S2 LOCK PLATE ASSEMBLY - HI & LOW SHIFT FORK SHAFT
S3 O-RING
S4 HI & LOW SHIFT FORK
S5 SHIFT FORK LOCK BALL
S6 COMPRESSION SPRING
S7 SCREW PLUG
S8 COTTER PIN
S9 HI & LOW SHIFT LEVER
S10 FRONT DRIVE SHIFT SHAFT BOOT