User's Manual

ManualsBrandsAdvance Lifts ManualsPet FenceAdvance Lifts Air Table ATT

Installation, Operation and Maintenance

Manual for the Following Equipment:

ALL AIR TABLES

MODELS, AT, ATT, ATR, ATI

In any correspondence with your distributor you will need the following information:

Model Number______________________ Serial Number_____________________________

Installation location: __________________________________

__________________________________

CAUTION:

Proper familiarization with this manual is essential for safe operation of the unit.

Carefully read the operating and maintenance instructions before operating the lift.

Distributor Information: ______________________________

_______________________________

Advance Lifts, Inc.

701 S. Kirk Road

St. Charles, IL 60174-3428

Toll Free 1-800-843-3625

Sales Fax 1-630-584-9405

Parts and Service Fax 1-630-584-6837

E-mail: Parts@advancelifts.com

*Advance Lifts, Inc. furnishes one manual with each unit. Additional manuals are available for

$25.00 each.

P 1-1

Summary of content (16 pages)

PAGE 1
Installation, Operation and Maintenance Manual for the Following Equipment: ALL AIR TABLES MODELS, AT, ATT, ATR, ATI In any correspondence with your distributor you will need the following information: Model Number______________________ Serial Number_____________________________ Installation location: __________________________________ __________________________________ __________________________________ CAUTION: Proper familiarization with this manual is essential for safe operation of the unit.
PAGE 2
SECTION 2. INDEX & INTRODUCTION Identification Sheet…………………………………………………………. Index & Introduction………………………………………………………… *Responsibilities Of Owners & Users….………………..……………….. *Installation Instructions……………………………..…………………….. *Operation Instructions……………………………………………………… *Maintenance Instructions……………………………………………….. … *Safety Bar Placement Warning Label Specifications & Locations ………………………………. Pneumatic Details……………………………………………………………..
PAGE 3
SECTION 3. RESPONSIBILITIES OF OWNERS & USERS Inspection and Maintenance: The lift shall be inspected and maintained in proper working order in accordance with this manual and safe operating practices. Removal from Service: Any lift not in safe operating condition shall be removed from service until it is repaired to the original manufacturer’s standards. Repairs: Authorized personnel in conformance with the manufacturer’s instructions shall make all repairs.
PAGE 4
SECTION 4. INSTALLATION INSTRUCTIONS Floor mounted units with baseframes, lift & turn, lift & tilt and tilt units: 1. Move the lift to the usage area; insuring the floor is clean and level. If slings are used, encircle the entire lift, not just the platform. Caution! Before securing the unit to the floor, shim or grout the entire baseframe assembly. Continuous baseframe support is essential for proper installation. 2. Connect the air supply line to the control valve.
PAGE 5
SECTION 5. OPERATING INSTRUCTIONS Pneumatic scissors lifts have an excellent safety record overall, but as with all moving equipment, they can be dangerous. Operators must use common sense and take responsibility for the safety of everyone near the lift. They must use the safety devices provided and be careful not to surprise anyone in the area with the movement of the lift. Pre-operational checks: 1. Check all air connections to be sure that they are completed properly and are operational. 2.
PAGE 6
SECTION 5. (CONTINUED) OPERATING INSTRUCTIONS Daily operation (continued): 4. On the first use of the lift each day, the operator shall check to see that the lift is functioning properly and smoothly. All safety devices shall be in place and operating correctly. 5. If the unit has a traveling air line, the operator must insure that it is kept away from the lift as it raises and lowers. 6.
PAGE 7
SECTION 6. (CONTINUED) MAINTENANCE INSTRUCTIONS 8. Never work on the pneumatic systems unless the unit is fully lowered or properly sitting on the safety support or wheel block. 9. Never apply a load to the equipment until the baseframe is continuously supported. 10. WARNING! Never expect to hold the leg assemblies open by simply lifting one end of a platform. A. The roller end of most lifts is not “gibbed” or captured in any way, so lifting on the roller end will simply tilt the platform. B.
PAGE 8
SECTION 6. (CONTINUED) MAINTENANCE INSTRUCTIONS SAFETY MAINTENANCE BAR INSTRUCTIONS WARNING! Always use the safety bars for any service or maintenance. Never go or reach under the lift unless both safety bars are securely in place and the power to the unit has been disconnected to prevent others from operating the lift. Never use the safety bars with a load on the platform. CAUTION! Never use the lift unless the safety bars are properly stored or damage may occur to the equipment. 1.
PAGE 9
SECTION 7. WARNING LABEL SPECIFICATIONS & LOCATIONS WARNING LABEL LOCATIONS & SPECIFICATIONS The warning and informational labels normally attached to P Series, LT and LTD lifts, are shown below and their proper mounting locations are shown on page 7-2. Descriptions of the labels are as follows: Label 1: This is simply a promotional label identifying the unit as Advance Lifts unit. Label 2: This is the formal nameplate and it shall never be removed from the unit.
PAGE 10
WARNING LABEL LOCATIONS PLATFORM FORMAL NAMEPLATE (DO NOT REMOVE) LABEL #2 BASEFRAME LABEL #2 PLATFORM LABEL #4 LABEL #5 BASEFRAME P 7-2
PAGE 11
SECTION 8. PNEUMATIC DETAILS FROM COMPRESSOR FLOW VALVE BLEED VALVE SUPPLY AIR (TO LIFT) SUPPLY AIR (TO LIFT) AIR EXHAUST FROM COMPRESSOR TYPICAL AIR CONTROLLERS The hand valve (left) is a typical two-position air valve. Constant pressure must be applied to the control knob for the lift to operate. The foot valve (right) is of a similar design and constant pressure on the pedal is required for lift operation. The foot valve is supplied with a protective cover that has been omitted for clarity.
PAGE 12
SECTION 9.
PAGE 13
SECTION 10. TROUBLESHOOTING HINTS Warning! Only qualified service personnel shall be allowed to perform service work on pneumatic lifts. The service person shall be familiar with this manual before attempting any service on the lift. Warning! No work shall be performed beneath a raised lift platform unless the safety leg or maintenance blocks are installed in accordance with Section 6 of this manual UNIT WILL NOT LIFT 1. Reduce load to rated capacity. 2.
PAGE 14
SECTION 11. ADVANCE LIFTS INC. WARRANTY For a period of one year from date of shipment from the Company’s plant, the Company agrees to replace or repair, free of charge, any defective parts, material or workmanship on new equipment. This shall include electrical and hydraulic components. For a period of ten years or 125,000 cycles (whichever occurs first) from date of shipment from Company’s plant, the Company agrees to replace or repair any defective structure.
PAGE 15
ADVANCE LIFTS “AT” SERIES PARTS LIST ROLLER WHEEL ASSEMBLY ROLLER WHEEL PIN (UPPER) ROLLER WHEEL PIN (LOWER) ROLLER PIN BEARING (ALL) ROLLER WHEEL SPACER (ALL) ROLLER WHEEL RETAINING CLIP ROLLER WHEEL WEAR PAD P-023-878 P-A-10346 P-A-9993 P-000-363 P-001-483 P-001-876 P-A-9555 MAIN AXLE PIN MAIN AXLE RETAINING CLIP MAIN AXLE BEARING P-A-9992 P-001-876 P-000-363 PLATFORM/BASEFRAME PINS PLATFORM/BASEFRAME CLIP P-A-9992 P-001-876 HAND VALVE BLEED VALVE FLOW VALVE AIR SPRING RELIEF VALVE P-001-318 P-001-
PAGE 16
052406