User's Manual

Quick Start
OPERATIONS MANUAL
Please register your product at www.silencer.com/manual .
CHANGING THE BATTERY IN YOUR TRANSMITTERS
TRANSMITTER OPERATION
Transmitter Button
System Function
Remark
Button
Lock door / ARM ARM (OPTIONAL)
– Button
Arm and Delete Optional
Sensor
Press twice.
(OPTIONAL)
Button
Car Locator While System Armed.
Button for 3 seconds
Panic function Press 3 seconds
Button
Unlock Door / DISARM
–
Button
Two Steps Door Unlock &
Disarm System
Press twice within 3
seconds. (optional
installation and
programming required)
Button for 3 seconds
Pop Trunk Release Press 3 seconds
+
Button
Silent LOCK / UNLOCK Ignition in "OFF" position.
+
Button for 1 seconds
Activate Car-Jacking
(OPTIONAL)
Ignition in
"ON"
position.
SILENT LOCK / UNLOCK
Switching code for 2nd
Car Operation
or CH4
ACTIVE LOCKING
–
LOCK & ARMING:
1. Press button on transmitter.
2. The siren or horn will chirp once and the parking lights will flash once indicating that the system
is now armed. The vehicle doors will lock upon arming when interfaced with the security
system.
Note: Defective sensor reminder: If the siren or horn sounds 3 chirps, then you have left a door,
trunk, or hood lid ajar. (OPTIONAL)
SILENT LOCKING AND UNLOCKING : ARMING / DISARMING: Press the
+
button
together on the transmitter to LOCK or UNLOCK your security system, No chirp sound will be heard;
arm / disarm confirmation will be through the vehicles parking lights only.
SHOCK SENSOR / OPTIONAL SENSOR BY-PASS: Pressing the
button on the transmitter twice
within 3 seconds will arm the security system and by-pass the shock sensor. The system will chirp
one additional time to confirm the sensor bypass mode was activated. The sensor bypass feature is
programmed to activate for one arming cycle only. The security system will return to normal operation
during the next arming cycle
PASSIVE LOCKING OR ARMING: Programmable
Active arming / disarming is controlling your security sys
tem v
ia the remote transmitter. This
security system is equipped with an optional Passive Arming feature, which allows the security
system to arm 30 seconds after the last door is closed. Operation is as follows.
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you
reopen any door / hood / trunk, the security system LED will stop
flashing. It will begin flashing
again
once all vehicle entrances are closed.
3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren or
horn will chirp [1] time and the parking lights will flash [1] time.
PASSIVE DOOR LOCKING:
Programmable
The vehicle doors will automatically lock after passive arming cycle has been completed.
ACTIVE UN-LOCKING – UNLOCK & DISARM:
1. Press the
button on the transmitter.
2. The siren or horn will chirp twice and parking lights will flash twice to indicate that the security
system is now disarmed. The vehicle doors will unlock when interfaced with the security system.
TAMPER DISARMING: (OPTIONAL). If the alarm is triggered; Upon disarming the system the
siren or horn will chirp 4 times and parking lights will flash 3 times. This will indicate that the alarm
has been triggered while armed.
TWO
STEP DOOR UNLO
CK: (OPTIONAL) This feature will independently unlock the drivers door
only when disarming the security system. Pushing the
button on the transmitter a second time
within 3 seconds will unlock the entire vehicle. (Optional, Additional installation required).
AUTOMATIC RE-LOCKING or RE-ARM: If this feature is selected, the security system will
automatically re-arm itself 60 seconds after disarming with remote transmitter. Automatic rearm will
cancel if any door is opened before the 60 seconds timer has elapsed.
DISARMING WITHOUT A TRANSMITTER
The Override function
may be used if the re
mote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to 'ON position. (Alarm will sound.)
2. Within 10 seconds push and release the valet switch
The alarm will stop sounding and enter the disarm mode. You can now start and operate the
vehicle normally.
VALET MODE:
The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand
your transmitter to park
ing atten
dants or garage mechanics. When the system is i
n valet mode,
all alarm functions are bypassed, however, the remote panic feature and remote door locks will
remain operational.
Enter Valet Mode:
1. Turn the ignition to “ON\OFF\ON” position.
2. Push and hold valet switch for 3 seconds or until the LED turns on. The LED will remain on as
long as the system is in 'valet mode'.
Exit Valet Mode:
1. Return to normal operation, turn ignition
'ON\OFF\ON'.
2. Push and hold valet switch for 3 seconds; the LED will turn o
ff indicating the system is exiting
the valet mode.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger the alarm in case of
emergency.
1. Press and hold the
button on the transmitter for 3 seconds. The alarm will immediately
sound.
2. To stop the alarm, press the
button on the transmitter, the panic mode will be turned off
immediately.
3. If the button is not pressed, the alarm will automatically stop after 30 seconds.
If you are not sure or do not understand any part of the quick start
manual, please download the complete operations manual available
at www.silencer.com/manual
.
TRIGGER THE SYSTEM:
(OPTIONAL) If alarm option is installed.
When armed, your vehicle is protected as follows:
1. Light impacts will trigger the warn-away signal. A long chirp from siren /horn.
2. Heavy impacts / Doors open / Hood open / Trunk open / Turning on the ignition switch- All will trigger the
programmed sequence.
The starter disable relay (if installed) prevents the vehicles starter from cranking. The siren or horn and parking
lights will turn on to alert of an
intrusion for 30 second
s. Then the siren or horn will stop and automatically reset
and re-arm. If any the sensors or detectors are still active, the alarm system will sound a maximum of 3-30
second cycles.
ANTI CAR-JACKING: (OPTIONAL) If alarm option is installed.
Warning: If you don't need the carjacking function in this alarm system, be sure to set carjacking feature
“OFF”. This system is default setting Car-jacking feature “OFF”.
1. TRANSMITTER ACTIVATES
THE CAR JACKING:
Press and hold
+ button on the transmitter for 1 second while the vehicles ignition is ON. The
parking light will turns on for 1.5” seconds to indicate car jacking activated.
2. DOOR SWITCH ACTIVATE CAR JACKING:
1. Turn the ignition switch to “ON” position, the system is armed.
2. Once the system is armed, if you are forced from the vehicle, the system will active the carjacking trigger
when the door is opened and closed while the ignition is “ON”.
TRIGGER THE CAR JACK MODE:
3-timer circuits will f
unction
as follows:
First timer:
a. 50 seconds after the system has been triggered. The siren or horn will start chirping for 15 seconds.
b. During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off the
car-jacking feature.
c. If not, it will enter second timer car jacking feature.
Second timer:
65 seconds after the system has been triggered. The siren or horn starts alarming and the parking light
starts flashing
.
Third timer:
90 seconds
after the system has been triggered
a. The siren or horn will still be alarming and the parking light flashing.
b. The starter disable will activate to prevent the vehicle from starting.
c. It will remain active until the vehicle's battery power exhausted.
OVERRIDE THE SYSTEM TO TURN OFF CAR JACKING:
Turn the ignition switch from OFF to ON, and within 10 seconds push valet switch. The siren or horn will
stop
and the system will be disarmed
IGNITION CONTROL DOOR LOCKS.
If the vehicle
s door locks have been interfaced to the security system, the system will automatically lock the
vehicle's doors when the ignition is turned “ON” and /or unlock the vehicles doors when the ignition is turned
“OFF”.
TRUNK RELEASE: Press and hold
button on transmitter for three seconds to remote control the trunk
release or other electric devices. ( Note: Vehicle must have an electronic trunk release )
CAR LOCATOR :
Press the
button on the transmitter when the vehicle is in the armed / locked mode to active
car locator function. The siren or horn will chirp 6 times. The parking light will flash 12 times, allowing you to
easily locate your car
.
ALARM OPERATING CONDITI
ON: (
OPTIONAL)
Function Siren or horn
Parking Lights
LED Doors
Starter
Disable
Pager
Option
1. Arm 1 Chirp 1 Flash Slow flash Locking On
2. Disarm 2or4 Chirps 2 or 3 Flashes Off or Fast flash Unlocking Off
3. Trigger Alarming Flashing Slow flash On On
4. Panic Alarming Flashing Slow flash Locking On
TRANSMITTER PROGRAMMING
Enter:
1. Turn the Ignition 'switch 'OFF/ON' 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and hold in on the 3
rd
push, when a long chirp is heard then release
the valet switch. You are now in the Transmitter programming mode.
Program:
1. Press any button on transmitter 1 until the siren responds with a confirming chirp; the first transmitter
is now programmed.
2. Press any button on the second transmitter un
til the siren responds with a confirming chirp; the
second transmitter is now programmed.
3. Apply the same procedure to program 3
rd
and 4
th .
Transmitters.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps and 3 parking Light flashes
will confirm exit.
Note: If more than 4 transmitters programmed, the system will only keep the last four.
Magnadyne Corporation
1111 W. Victoria Street
Compton CA 90220
[phone]
For Warranty information: Please visit our website at www.silencer.com
Made in Taiwan. All Rights Reserved
UM-QR-SL-3S rev A
SLRF434: The transmitter uses one 3-volt lithium ion batteries (#CR2032) To replace the battery,
you will need to use a small flat blade screwdriver. Locate the small notch on the lower left side of
the transmitter case next to the key ring. Using the flat blade screwdriver, carefully pry the top case
from the bottom case. It should snap apart after breaking the seal. Before removing the battery note
the direction of the positive (+) terminal. Place the new batteries in exactly the same manner, being
careful not to bend or damage the contact terminal. Snap the cases back together and then test the
transmitter to insure it arms and disarms the alarm.
SLRF434
Transmitter
Battery
Replacement
CR2032 ( 1 )
+ Side DOWN
+
For 1-way TX only, Press
& hold until TX LED on