2013/05/29 MODEL NO.
013/05/29 LCD REMOTE CONTROL TRANSCEIVER: A. BATTERY REPLACEMENT: This system needs no specific maintenance beyond remote control battery replacement. The 2-way remote is powered by a 1.5V AAA battery. The 1-way remote is powered by a 3V, CR2032 battery Battery Level Indicator (2-way remote) The Battery Level indicator has three level indicators that serve as a visual indication of battery charge.
2013/05/29 PASS 1 12:00 Timer Control Start Engine start automatically every 2 or 3 hours. Daily Start Engine start automatically at the same time next day Sensor Bypass Sensor 1bypass under Arm mode Turbo Timer Turbo timer was set up Manual Gear Engine Start Memorizing for the car with manual gear was set up Activate Channel 3 (Trunk Release). Activate Channel 3 Activate Channel 4 Time Monitor 12:00 0:10 P Parking Meter C.
2013/05/29 Press and hold the F MENU flashing Press Button until 2 beeps button to enter 2-way HHU menu mode sounded Press F Button 2 nd STATUS CHECK Press time (HHU 1 beep) button Enable to check the vehicle’s status. within 5 seconds Press F Button 3rd ALARM CHECK Press times (HHU 1 beep) button Enable to check vehicle’s trigger status. within 5 seconds Press F Button 4th VOLTS CHECK Press times (HHU 1 beep) button Enable to check vehicle’s Voltage.
2013/05/29 Adjust Alarm Clock 12 :00 hours from 0 to 12 12 is flashing Press button = (+) or Press button = (-) Press button confirm its selection, move to next option. Adjust Alarm Clock minutes from 0 to 12: 00 00 is flashing 59 Press button = (+) or Press button = (-) Press button confirm its selection, move to next option. Select Alarm Clock ON + or Enable or Disable OFF Press button = Enable or Press button = Disable Press button confirm its selection, move to next option.
2013/05/29 5 or 2-way HHU Response mode VIBRO Select 2-way HHU confirmation by Melody or Vibration 6 Second Car Default is Buzzer + VIBRO + BZ+VIB + or or + Press button = Melody or Press button = Vibration Press button confirm its selected, move to next option. Default is CAR 1 CAR SELECT Security Option Car Select CAR 2 7 ( II icon On) - CAR 1 operation. nd - CAR 2 operation (II icon On mean 2 car operation).
2013/05/29 Press & Release “ F” button to move cursor flash to Daily Start icon Press Daily start icon flash button Enable Daily start mode. Icon On = Enable Icon Off = Disable Press & Release “ F” button to move cursor flash to TIME START icon Press Timer start icon flash button Enable Timer Start mode. Icon On = Enable Icon Off = Disable OPERATION: A.
2013/05/29 2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The vehicle’s doors will lock upon arming if interfaced with the security system. DEFECTIVE SENSOR REMINDER: If the siren sounds 3 chirps and parking light flash one time, then you have left a door, trunk, or hood lid ajar.
2013/05/29 Note : You must override the alarm within 60 seconds. If not, the system will automatically re-arm. EXAMPLE: To Override The System With The Password Code 83, 1. Enter the vehicle and turn the ignition switch to the 'ON’ position. (Alarm will sound.) 2. Within 5 seconds, Press and Release the Valet Switch 8 times, (When finished the system's siren will stop alarming, lights stop flashing, but the vehicle can not be started or driven away.) st 3.
2013/05/29 1.Under ignition on press F button four times while “CAR JACK” flash on text area(see Table 1), then press button for 2 seconds to activate Anti Car-Jacking mode or and buttons at the same time for 2 seconds. The parking Under ignition on press and hold the lights will turn on for 1.5 seconds to indicate the system enter the anti car-jacking mode. 2.Once the system in anti car-jacking mode, the system will be triggered when the door is opened and closed while the ignition is “ON”.
2013/05/29 U. POWER SAVER MODE (Default OFF) By table - 2 -1– 4 under Menu mode while “POWER SAVE” icon flash press button, LCD HHU show “Save” unit under power save mode, the LCD remote transceiver use “0” current to save the battery power, LCD indicate “SAVE “. Exit: Press any button of the LCD remote transmitter to exit “Power Save Mode”. V. POWER ON MEMONRY: This security system is equipped with circuitry that will allow the unit to remember its alarm state if the power is lost and then reconnected.
2013/05/29 1.Before turning off the engine, press the button once on the transmitter and the LED indicator will flash 3 times to confirm. 2.Turn the ignition key to OFF position. (The engine will stay running.) 3.The engine will run until the pre-programmed time elapsed or shutdown input is received. D.
2013/05/29 more times, the LCD remote will show “TEMP CHECK“ icon (see Table 2- 5), then press button; the in-door temperature will be shown on the LCD screen. This reading may be higher than actual ambient temperature due to the greenhouse and is relative only the inside vehicle temperature. G. TO TURN OFF THE REMOTE START: When the engine is running (by remote start), if you want to stop it, 1. Press button once on the remote transmitter under remote start mode. 2.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
