Installation Manual for Drop In Sinks

ManualsBrandsAdvance Tabco ManualsCommercial Drop in Weld In and Undermount SinksDI-1-5-2X One-Compartment Drop-In Sink with 5" Deep Bowl and Deck Mounted Gooseneck Faucet (Minimum Order of 7 Units)

EDGEWOOD, NY 11717-8380

INSTALLATION INSTRUCTIONS for

DROP-IN SINKS

CHECK FOR CONCEALED DAMAGE

FILE CLAIM WITH FREIGHT CARRIER

op-ins manufactured by

ADV

ANCE TABCO

e designed and

constructed for countertop installations. Only one compartment

units intended for HAND SINK USE ar

e NSF listed and

approved. Suggested end use for drop-in sinks include dump

sinks, bar sinks, wash sinks and hand sinks.

STEP 5

• Remove masking tape from counter

surface and position sink into opening to

ensure proper fit.

STEP 6

• Remove sink from opening and apply

1/4” bead sealant along edge of cut out.

• Install sink into counter top.

• Insert slotted end of screw thru clearance hole in clip and

secure by turning Counter-Clockwise.

• Slide clip into end of Roll Form track (As

Shown) and position where desired and

hand tighten. Once all clips are in posi-

tion, tighten with screwdriver -

DO NOT OVERTIGHTEN!

• Wipe excess Silicone from counter

surface.

STEP 7

• Connect Drain and Faucet supply lines.

STEP 4

• Install Faucet (as shown).

ANCE T

ABCO, June 2005

STEP 1

Remove all contents from carton.

(

NOTE: Check for concealed damage - Notify Carrier of

any damages immediately)

STEP 2

• Position sink (upside down) onto counter top surface at

desired location. Trace outer edge of Self-Rim with pencil.

(NOTE: Ensure sink is parallel to counter edges. Procedure

does not apply to DI-1-30, DI-1-5SP or DI-1-10SP.

Refer to chart for Cut Out dimensions.)

• Remove sink and draw a second line 3/8” parallel to the

inside of the marked line - that will be the CUT line

(As shown).

• NOTE: BEFORE CUTTING

COUNTER TOP, REFER TO THE

CHART TO VERIFY CUTOUT

DIMENSIONS!

REMEMBER:

MEASURE TWICE, CUT ONCE!

• Drill 1/4” hole 1 to the inside of cut line then use 1/2” drill

bit to enlarge hole.

• Apply masking tape along outer (sink edge) line. This will

prevent damaging countertop while cutting.

• Position jig saw blade into 1/2” hole and follow CUT LINE.

<< CORRECT MARKING

PROCEDURE

Pencil MUST be held

straight as possible.

INCORRECT >>

MARKING

PROCEDURE

Rubber W

asher

Fiber Washer

Die Cast Nut

STEP 3

• Install Drain -

Apply a bead of

Plumber’s Putty

as shown.

1/4” continuous bead of

Plumber’s Putty.

3/8

Summary of content (2 pages)

PAGE 1
STEP 1 Remove all contents from carton. (NOTE: Check for concealed damage - Notify Carrier of any damages immediately) STEP 4 • Install Faucet (as shown). STEP 2 • Position sink (upside down) onto counter top surface at desired location. Trace outer edge of Self-Rim with pencil. (NOTE: Ensure sink is parallel to counter edges. Procedure does not apply to DI-1-30, DI-1-5SP or DI-1-10SP. Refer to chart for Cut Out dimensions.
PAGE 2
This Carton Contains: NOTE: The corners of ALL Cutouts are to have a 1-1/4” Radius. SMART SERIES™ LENGTH IS LEFT TO RIGHT MODEL # Bowl Dim. LxWxD Overall Dim.