Dish Machine Compatibility Chart

Dish Machine coMpatibility chart
The Following Dish Machines Require SMART FABRICATION
™
Modifications For Dishtable Compatibility.
1
Updated as of 3/1/2016
Continued on Page 2 ☛
ADS
(American
Dish Machine)
ADC44, ADC66 Sink bowl must be 20” from dish machine. Add DTA-76 to soil dishtable.
HT-25, SS-25 If dish machine is in corner, backsplash must be notched to 4” tall to clear handle. Add DTA-78 to table that’s on
front of machine.
AFC-3D, AF-3D, AF-ES, AFC-ES, AF-W,
L3-DW, L3-DWC, Lxx-3DW, Lxx-3DWC,
5-CD, 5-AG, 5-AG-ES
NO MODIFICATION NEEDED.
APEX
SEE ECOLAB
Autochlor
AC-44 No sinks or other obstructions within 20” of machine on soil side (add DTA-76) or 10” of machine on clean side.
A4, A5, D2 NO MODIFICATION NEEDED.
Blakeslee
D-8, D-9, R-MM-100 If dish machine is in corner, right side backsplash must be notched to 4” tall to clear handle. Add DTA-78 to the
right table.
R-L-40, RM50 Must maintain 13” clear on clean side of machine.
R-CC-64, R-LL-80, R-MM-100 No sinks or other obstructions within 13” of machine on clean side.
Burns
A2 NO MODIFICATION NEEDED.
Champion
DH-5000 Genesis If dish machine is in corner, right side backsplash must be notched to 3” tall to clear handle suggest (but not
required) 12” clear on right side table to operate controls. Add DTA-78.
44DR, 54, 66DRPW, 70DRFFPW,
76DRPW, 80DRHDPW, 80DRFFPW,
90DRHDPW, DH-2000
NO MODIFICATION NEEDED.
64, 84, 86PW, 90FFPW, 100HDPW,
106PW, 110FFPW, 120HDPW
Must maintain 10” clear on clean (exit) side of machine.
DL-2000 No obstructions within 6” of machine.
D-HB, D-LF, D-FL, DH-1000 NO MODIFICATION NEEDED.
CMA
(Chemical Methods)
Energymizer
180 Right side sinks bowls must be 12” from dish machine. Add DTA-76 if sink is on right table.
EST-44H, EST-44L, EST-66H, EST-66L Sink bowl must be 12” from dish machine. Add DTA-76 to soil dish table. NO obstructions on clean side
(including channels) within 12” of machine.
B, AH, C, E-AH, E-AH-EXT, E-C, E-C-EXT,
EST-3D, EST-3D-EXT, EST-C, EST-C-EXT,
EST-AH, EST-C, CB, S-B
NO MODIFICATION NEEDED.
Ecolab
EC-44, EC-66, ES-4400, ES-6600, ES-8000 Clean (exit) side no obstructions under table within 12” of machine.
ES-4000, APEX-TSC-Double No modifications for straight thru operation. If used in a corner (ES-4000-CDR or CDL, TSC-Double right or left
one table backsplash must be notched to 4” tall. Add DTA-78 to right models or left models.
ET-14 If sink is on right side of dish machine and deeper than 10”, sink must be 16” from machine. Add DTA-76 to soil
table if required.
ET-44 Right side sinks bowls must be 12” from dish machine. Add DTA-76 if sink is on right table.
WH-44, WH-66 Sink bowl or waste trough must be 14” from machine, regardless of direction flow. Add DTA-76 to soil table.
APEX TSC-V This dish machine has a control box that can be relocated. In some situations, a 9” or deeper bowl on a right
side
ES-2000, APEX-TSC, Inferno, Typhoon NO MODIFICATION NEEDED.
APEX HT Right side sinks and troughs must be at least 6” from dish machine.
Electrolux
WT44 Sinks and troughs (and all other obstructions) recommended to be 20” from machine. Add DTA-76 if required.
WT65, 504262, 504263, EHT8ILG4,
EHT8ILG8
If dish machine is in the corner, left side table backsplash and front rolled rim must both be cut down 2” tall, add
DTA-78.
504252, 504253, 504279, 504280, EHT-
8TIELG4, EHT8TIELG8, EHT8IELG4
Each table requires an angle spot welded under top along machine lip. Add $75 net per table. For corner
operation, left table requires backsplash notched to 3.5” tall to clear handle. Add DTA-78 to left table if required.
Eurodib
L21 NO MODIFICATION NEEDED.
L25EK, L25EKDSP Require a special machine opening 20 3/32 K-508A. Front rolled edge needs 1” tall by 2” long flat section at
machine, angled at end. Add K-508A. if a corner set up, left side table needs rear splash cut down to 1” for 2”
closest to machine. Add DTA-78.