Installation Instructions for SHD Series Drawers

ManualsBrandsAdvance Tabco ManualsCommercial EquipmentSHD-2020-X SHD Series 20" Deep Heavy Duty Drawer for Work Tables with Stainless Steel Front and Inset

CHECK FOR CONCEALED DAMAGE

FILE CLAIM WITH DELIVERING FREIGHT CARRIER

Drawers manufactured by ADVANCE TABCO are designed and constructed for stor-

age. Applications may include storage of ﬂatware, small utensils, etc. ADVANCE TABCO

does not recommend product use for activities employing harsh and active chemicals.

Please consult factory regarding unusual applications.

Installation Instructions for

SHD Series Drawers

Summary of content (8 pages)

PAGE 1
Installation Instructions for SHD Series Drawers CHECK FOR CONCEALED DAMAGE FILE CLAIM WITH DELIVERING FREIGHT CARRIER Drawers manufactured by ADVANCE TABCO are designed and constructed for storage. Applications may include storage of flatware, small utensils, etc. ADVANCE TABCO does not recommend product use for activities employing harsh and active chemicals. Please consult factory regarding unusual applications.
PAGE 2
Contents: (1) Outer Drawer Chassis (1) Inner Drawer Chassis (1) Stainless Steel Drawer Pan (4) 1/4-20 x 1/2” Bolts with Nuts Tools Required: (2) 7/16” Open end Wrenches Step 1: Fully extend Inner Drawer Chassis and remove stainless steel Drawer Pan (Figure 1). Figure 1 Step 2: Remove Inner Drawer Chasis by lifting up on drawer front handle to clear “Safety Stop” (Figure 2). Figure 2 Step 3: Install Outer Chassis to Work Table Drawer Angles under side of table top (Figure 3).
PAGE 3
NOTE: When installing on 24” wide Work Tables, use “Front” set of mounting holes. When installing on 30” & 36” wide Work Tables, use “Rear” set of mounting holes (Figure 4a & Figure 4b). 30” & 36” Work Table Mounting Holes 30” & 36” Work Table Mounting Holes 24” Work Table Mounting Holes 24” Work Table Mounting Holes (Figure 4a) FRONT OF DRAWER SHOWN (Figure 4b) REAR OF DRAWER SHOWN Step 4: Install Inner Drawer Chassis. NOTE: Align rear Inner Chasis Bearing with Flange of Outer Chassis (Figure 5).
PAGE 4
Installation for Stacking SHD Series Drawers Step 1: Remove stainless steel Drawer Pan and Inner Drawer Chassis from existing SHD Drawer mounted to Work Table. Step 2: Remove Stainless Steel Drawer Pan and Inner Chassis of SHD Drawer to be added (See Figure 1). Step 3: Align top flange of outer Chassis with bottom flange of existing SHD drawer. Install 4 Bolts (provided) thru holes on both sides of Drawer secure with Nuts.
PAGE 5
OPTIONAL CONCEALED SIDE PANELS 1 Drawer: 2 Drawers: 3 Drawers: TA-SHD-1 (Per side) TA-SHD-2 (Per side) TA-SHD-3 (Per side) NOTE: Panels Are Sold Individually, Not In sets Contents: (1) Side Panel (4) 1/4 - 20 x 1/2” Bolts with Nuts (Per Panel) Tools Required: (2) 7/16” Open End Wrenches Step 1: Remove Stainless Steel Drawer Pan and Inner Chassis (See Figure 1). Step 2: Align holes of Side Enclosure Panel with holes on top & bottom flanges of outer Chassis.
PAGE 6
Installation for TA-90 DRAWER ADAPTER Contents: (2) Drawer Angles (4) Self Tapping Screws Tools Required: Drill with 1/8” Drill Bit 3/8” Socket Step 1: Turn table top upside down - Position Drawer Adapter (TA-90) at desired location. NOTE: Position Drawer Adapters 21-1/2” apart (outside angle to outside angle) and 3” from front edge of table - mark holes and drill with 1/8” drill (Figure 2).
PAGE 7
TA-97SHD Poly Storage Bracket For SHD Series Drawers (Poly Board TA-41SHD Not Included) Contents: (2) Poly Storage Brackets (4) 1/4 - 20 x 1/2” Bolts with Nuts Tools Required: (2) 7/16” Open End Wrenches Step 1: Remove Stainless Steel Drawer Pan and Inner Chassis (See Figure 1). Step 2: Position Poly Storage Bracket such that the opening faces the front of the Drawer. Align the (2) holes at the top of the TA-97SHD with the holes in the bottom Flange of the existing SHD Drawer (See Figure 10).