User Manual

ManualsBrandsAdvanced Control Technologies ManualsElectronicsUSB Interface Device

DSH, Datasheet

ZM1220 Z-Wave Module

Document Part Number: 903501205

Document Revision: 01.05

Description:

Datasheet for the Integrated Z-Wave Module based on

ZW0102 Z-Wave Single Chip. Two versions are described

within this document, US version (908.42MHz) and a EU

version (868.42MHz).

Written By: Thomas Jørgensen

Date: February 5, 2003

Reviewed By: MVO, OPP, JFP, MHA, TBA, LAF, NTJ, TCA

Audience: For R&D internal and R&D external distribution

Internal R&D File Name: ZW0102_ZwaveModule.dsh.001.01.05.doc

Approved by:

Authority

Date

Niels T. Johansen, R&D 2/5-2003

This document is the property of Zensys A/S. The data contained herein, in whole or in part,

may not be duplicated, used or disclosed outside the recipient for any purpose other than to

conduct technical evaluation. This restriction does not limit the recipient’s right to use

information contained in the data if it is obtained from another source without restriction.

CONFIDENTIAL

Summary of content (15 pages)

PAGE 1
DSH, Datasheet ZM1220 Z-Wave Module Document Part Number: 903501205 Document Revision: 01.05 Description: Datasheet for the Integrated Z-Wave Module based on ZW0102 Z-Wave Single Chip. Two versions are described within this document, US version (908.42MHz) and a EU version (868.42MHz). Written By: Thomas Jørgensen Date: February 5, 2003 Reviewed By: MVO, OPP, JFP, MHA, TBA, LAF, NTJ, TCA Audience: For R&D internal and R&D external distribution Internal R&D File Name: ZW0102_ZwaveModule.dsh.
PAGE 2
DSH, Datasheet 903501205 May 1, 2003 REVISION RECORD Doc. Rev Date 00.01 01.00 01.01 By May 15, TJO 2002 June 13, TJO 2002 August 19, TJO 2002 Pages affected ALL Brief description of changes ALL First release Initial Draft 7, 9, 11, Table 2: “AD1: Can be used as voltage reference input” removed 12, 16 Section 4.2.4: “external voltage reference” removed Table 5: RF receiver sensitivity updated Table 6: “Absolute Maximum Ratings” updated Table 7: Updated Chapter 6: Reference 1 updated 01.
PAGE 3
DSH, Datasheet 903501205 May 1, 2003 Table of Contents 1 ABBREVIATIONS.............................................................................................................................................4 2 INTRODUCTION ..............................................................................................................................................4 2.1 Purpose .........................................................................................................................
PAGE 4
DSH, Datasheet 1 903501205 May 1, 2003 ABBREVIATIONS Abbreviation ADC API FSK GPIO HW I/O LSB MCU MSB OEM PCB RF RTC RX SPI SRAM SRD SW TX UART ZM1220 ZW0102 Explanation Analog-to-Digital Converter Application Programming Interface Frequency Shift Keying General Purpose Input/Output Hardware Input/Output Least Significant Bit Micro Controller Unit Most Significant Bit Original Equipment Manufacturer Printed Circuit Board Radio Frequency Real-Time-Clock Receive Serial Peripheral Interface Static Random
PAGE 5
DSH, Datasheet 903501205 May 1, 2003 3 PRODUCT DESCRIPTION 3.1 Overview The ZM1220 Z-Wave Module is a central part of Zensys’ Integrated Z-Wave Module family and is based on Zensys’ Z-Wave Single Chip ZW0102. The ZW0102 is a single chip containing a RF transceiver, an 8051 micro-controller, a wide range of HW interfaces and Z-Wave SW Application Programming Interface (API).
PAGE 6
DSH, Datasheet 903501205 May 1, 2003 The Application Connector interfacing the Z-Wave Module with the Application Module is a standard 2.00mm pitch 2x10 pin-row.
PAGE 7
DSH, Datasheet 903501205 May 1, 2003 4 HW SPECIFICATIONS 4.1 Application Connector Specification The Application Connector interfacing the Z-Wave Module with the Application Module is a 2x10 pin row. The connector layout shown in Table 1 is a part of a Zensys defined Application Connector layout, which has been designed to allow exchange of the ZM1220 Z-Wave Module with another Z-Wave Module type.
PAGE 8
DSH, Datasheet 4.2 903501205 May 1, 2003 Application Connector Signals 4.2.1 GPIO Pins Some of the signals, which have a special feature, can also be used as General Purpose Inputs/Outputs pin (GPIO) if wanted. All GPIO’s signals have true Read-Modify-Write functionality when used as general digital I/O ports. The “special” purpose signals, which can be used as GPIO are listed in the table below. • • • • • • • • INT0_n TXD RXD MOSI MISO CLK TRIAC XEROX For electrical characteristics see section 4.
PAGE 9
DSH, Datasheet 4.2.4 903501205 May 1, 2003 Analog-to-Digital Converter Either AD1 or AD2 on the Application Connector can be used as Analog-to-Digital Converter (ADC) input. The ADC is a 10-bit ADC. An internal (ZW0102) voltage reference can be used. For detailed description and electrical specifications see [1]. 4.2.5 TRIAC & ZEROX The Z-Wave Module has a triac control output signal (TRIAC).
PAGE 10
DSH, Datasheet 4.6 903501205 May 1, 2003 Power The Z-Wave Module can be powered by either 3.3V or 5V by the Application Module. If powered by 5V a 5V-to-3.3V DC/DC converter must be mounted on the Z-Wave Module. As indicated in Table 7 the power supply must be quite stable, so it does not create noise in the noise circuitry, resulting in reduced RF sensitivity. 4.
PAGE 11
DSH, Datasheet 4.9 903501205 May 1, 2003 MCU Specification MCU MCU Type MCU speed Flash SRAM SRAM (CPU) MCU Peripherals Interrupt sources Description Optimized 8-bit 8051 MCU core (4 clock cycles per instruction), See [1]. 7.376974 MHz 32kbyte. Programmed through the SPI interface. 2kbyte 128 byte 10-bit ADC, UART, SPI, 8 bit timer, 2x16 bit timer one with PWM mode, watch dog timer, Power-on Reset/Brown-Out Detector. Internal and external. Table 3 MCU Specifications 4.
PAGE 12
DSH, Datasheet 903501205 May 1, 2003 4.12 Electrical Specification 4.12.1 Absolute Maximum Ratings The “Absolute Maximum Ratings” specifies the conditions in which the Z-Wave Module is guaranteed not to be destroyed but correct operations are not guaranteed. Exceeding the “Absolute Maximum Ratings” may destroy the Z-Wave Module. See “DC Characteristics” for guaranteed operation limits.
PAGE 13
DSH, Datasheet 903501205 May 1, 2003 4.13 Physical Specification Physical Dimension (H x W x D) Mounting holes Description 7 mm x 50 mm x 40.5 mm Two holes. Table 8 Physical Specifications 40.5mm 2.0mm PCB Antenna Pin 20 J1 Pin 19 Holes Button 31.0mm 12.0mm 50.0mm 25.0mm H2 Pin 1 29.0mm 35.0mm Figure 2 ZM1220 Z-Wave Module PCB outline The Application Connector is a standard 2mm pitch 2x10 pin-row. The pad hole is a Ø0.9mm plated hole.
PAGE 14
DSH, Datasheet 903501205 May 1, 2003 5 SW SPECIFICATION 5.1 Free SW resources The Z-Wave protocol does not use all of the available SW resources on the ZM1220 Z-Wave Module. The following sections describe the resources left for OEM SW for the different Z-Wave protocol API devices. For further information on these Z-Wave Slave and Z-Wave Controller API packages, see [5] and [6]. 5.1.1 Z-Wave Slave Free resources when the ZM1220 Z-Wave Module is loaded with a Z-Wave Slave protocol package.
PAGE 15
DSH, Datasheet 903501205 May 1, 2003 6 REFERENCES A Zensys documentation part number consists of 9 digits where the last two digits refer to the revision of the document. When the revision is listed as “XX” please refer to the latest revision of the document. [1] [2] [3] [4] [5] [6] [7] Zensys A/S Datasheet, ZW0102 Single Chip, Doc. P/N: 9035016xx Datasheet, ZM1206 Z-Wave Module. Doc.