Installation guide

ManualsBrandsAdvanced Keys ManualsAutomotiveAK-PSB05

ADVANCED KEYS

Smart Keyless Entry System

INSTALLATION GUIDE

AK-104

REV: A05-11-1118

www.advancedkeys.com

support@advancedkeys.com

Product Features:

• Smart Keyless Locking/Unlocking

• Compact Sized Smart Keys

• Dual-Antenna Setup

• Bypass Transponder RFID Cards

• Vehicle Anti-Theft Function

• Ignition Controlled Lock / Unlock

• Auto Vehicle Battery Power Saving

• Door-Not-Closed Reminder

• Smart Key Battery Low Reminder

• Locking-Delay Function

• Compatible with Push-Start Ignition

• Auto Window Closing Output

Summary of content (11 pages)

PAGE 1
AK-104 REV: A05-11-1118 ADVANCED KEYS Smart Keyless Entry System INSTALLATION GUIDE Product Features: • • • • • • • • • • • • * Smart Keyless Locking/Unlocking Compact Sized Smart Keys Dual-Antenna Setup Bypass Transponder RFID Cards Vehicle Anti-Theft Function Ignition Controlled Lock / Unlock Auto Vehicle Battery Power Saving Door-Not-Closed Reminder Smart Key Battery Low Reminder Locking-Delay Function Compatible with Push-Start Ignition Auto Window Closing Output www.advancedkeys.
PAGE 2
TABLE OF CONTENTS Table Of Contents ..................................................................................... 2 Product Contents ..................................................................................... 2 Warning and Safety Information ............................................................ 3 Safety Precautions ................................................................................ 3 Pre-installation Considerations .......................................................
PAGE 3
WARNING AND SAFETY INFORMATION PRODUCT SAFETY AND LEGAL DISCLAIMER • This product shall be installed by a certified technician therefore a certain level of competence and knowledge are therefore assumed when reading this guide. • This guide is provided as a GENERAL installation instructions and vehicle subjected to installation maybe different. • This product is designed based on vehicle regulatory standard. Please observe your local public road traffic law and regulations prior to installation.
PAGE 4
MAIN HARNESS WIRING DESCRIPTIONS JP1 JP2 JP3 JP4 Main Harness 8-Pin 18 AWG Brown Trunk Release Grey 7.5A Parking Light Grey 7.5A Parking Light Red 15A Battery +12V Green 15A Lock Blue 15A Black Unlock Ground Purple Wiring Description: Brown OUTPUT ̶ JP3 JP4 Horn Control + + + - 500mA Trunk Release Connect to the negative side of the trunk release trigger. This output will provide 1 second pulse when UNLOCK button is pressed for 2 seconds.
PAGE 5
JP1 JP2 JP3 JP4 Accessory Harness 7-Pin 22 AWG ACCESSORY HARNESS WIRING DESCRIPTIONS White Purple Starter Kill Relay Control JP2 OPTIONAL Brown Blue - Push-Start Module Control ~ Brake + OPTIONAL Window Closer Module Control Green - Door Switch JP1 Red ACC + + Ensure all connections are completed and properly secured prior to connecting the wire harnesses to the module.
PAGE 6
CONNECTIONS CONTROLLER WIRING DIAGRAM JP1 JP2 JP3 Jumper Settings: JP4 Default Settings Optional Settings JP1 Neg.(-) Door Trigger Pos.(+) Door Trigger JP2 Ground-When-Armed Ground-When-Disarmed JP3 Single Unlock Pulse Double Unlock Pulses JP4 OEM Horn Output Siren Output Legend: Input + Positive Type Output Negative Type ~ Frequency Type In-Line Fuse - Brown Trunk Release Main Harness 8-Pin 18 AWG Grey 7.5A Parking Light Grey 7.
PAGE 7
INSTALLATION INSTALLATION OVERVIEW Use following steps as a guide to install this system: Review product manual manual. Prepare vehicle for installation. Mount LED, secure controller and close-up installation. Review and set controller jumper settings according to requirements. Connect Main and Accessory Harness. Pre-position antennas and antenna wiring. Verify smart keys and bypass transponder card function/range then route and secure antennas to final position.
PAGE 8
PROGRAMMABLE FEATURES (CONT.) Ignition-Controlled Door Lock Enabled by default and controlled by Brake input, this function will provide: • Auto Door Locking when ACC is turned ON while brake is applied. • Auto Door Re-Locking when brake applied after door opened-then-closed. • Auto Door Unlocking when ACC is OFF. To disable Ignition-Controlled Door Lock feature, press and hold the brake pedal when powering ON the controller.
PAGE 9
FAQ Why is key detection not working or the range is very sort? Verify antenna position: Antenna may be on or close to metallic material, change position to verify range sensitivity. Check antenna wiring, do not pull on the antenna wires, make sure connectors are firmly seated. If remote failed to work both in proximity and manually press the buttons, follow key programming procedure to relearn all keys. What does each LED color status mean? See User Manual for more information on LED status detail.
PAGE 10
KEY PROGRAMMING PROCEDURE If required, use the following procedures to program a new set of Smart Key and/or Bypass Transponder Cards. Both set of Smart Keys or the Bypass Transponder Cards must be present and accessible during programming. Enter Programming Mode Disarm the system by a valid Smart Key or Bypass Transponder Card. Turn the Ignition Key to the ACC position.
PAGE 11
CLOSING UP • Connecting the wire harnesses and power ON the controller, check and confirm system operations (Refer to User Manual) then verify functions of the vehicle are in working order. • Make sure all wiring connection are insulated properly. Place and secure control units to locations inside trim panels and bundle all lose wiring. Put back all trim panels • When mounting the controller unit in the vehicle, consider the location carefully.