S SERIES Retractable Awning Owner’s Manual For safety reasons, please read the instructions and warnings in this manual carefully before installing the awning.
TABLE OF CONTENTS Safety instructions and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Package contents and parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Tool requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Product features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY INSTRUCTIONS AND WARNINGS TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY • Pay close attention during installation to ensure that the Advaning awning is installed properly. • Perform the installation in dry and optimal conditions. Always wear protective gear and gloves when handling sharp metal parts. If you do not feel that you can properly install the awning, please seek professional help.
PACKAGE CONTENTS AND PARTS Before installation, make certain that the package contains all parts as listed on this page.
TOOL REQUIREMENTS 3 1 Minimum 2 people to install 4 2 5 SUGGESTED TOOLS 10 6 1 Marker / pencil 2 Measuring tape 3 Electronic Stud finder 4 Chalk line / laser level 5 Level 6 3/8” socket wrench 7 Drill bit 8 Masonry drill bit 9 Drill with bits 10 Ladders (2) 9 7 8 Fig.4 PRODUCT FEATURES 10 2 11 1 4 3 9 12 9 8 5 6 Fig.5 7 1 2 3 4 5 6 Toll Free (US): (855) 574-0158 Arm shoulder Crank loop Torsion bar Roller tube Awning fabric Front bar www.advaning.
INSTALLATION NOTE: The left most bracket must be placed on the outer left side of the awning shoulder. The right-side brackets must be placed on the outer-right side of the right awning shoulder. BRACKET PLACEMENT REFERENCE CHART Please use the charts for bracket location reference. A Left awning shoulder B Right awning shoulder ALL brackets must be mounted onto wall studs or other major structural supports. B A 8 ~ 10 feet awning B A 12 ~ 13 feet awning Fig.6 5 www.advaning.
INSTALLATION DETERMINE WHERE TO INSTALL YOUR AWNING Roof, eave or overhang B Minimum 1 inch C Minimum 10 inch clear space Locate a position that is A A At least 10 feet above the ground/floor/ deck. B Minimum 1 inch clearance below the roof/ eave/overhang. C With at least 10 vertical inch of clear space. Minimum 10 feet D Minimum 8 feet Ground, floor or deck Fig 7 The surface should be free and clear of any obstructions along the entirety of the awning. D Minimum width.
INSTALLATION INSTALLING WALL BRACKETS Standard stud installation 1 Minimum 1 inch 1 2 Measure and mark where the top of your awning bracket will be placed. 2 Use a regular level and chalk line or a laser level, mark a straight level line. 3 Locate and mark the center of the wall studs along this line using a stud finder. *Please follow the directions of your stud finder as instructed by the manufacturer.
INSTALLATION 8 9 Place brackets over the appropriate holes and use a level to make sure the bracket is leveled and square to the line. Use a washer and lag screw to secure all the brackets until snugged against the surface. Level 9 8 washer Lag screw Wall Bracket Bracket Fig 13 Fig 14 NOTE: For proper installation of brackets on uneven surfaces or siding, use shims or spacers to level the bracket.
INSTALLATION 1 Follow instructions for standard installation step 1 and 2 (page 7). 2 Use the recommended bracket location chart (page 5) to find bracket location for your awning model along the line. 3 Align the top of the bracket to the chalk line and use a level to make sure the bracket is straight. 4 Mark the center of the bracket mounting holes. 5 2 Bracket locations base on your awning model Fig 17 3 4 Drill mounting holes using a masonry drill bit.
INSTALLATION Insert an expansion bolt set into each of the drilled bracket holes. 6 7 Leave the hex bolt head outside of the hole. 8 Tighten the hex bolt head. 6 Tighten bolt head 8 Expansion bolt set 7 Socket wrench Leave hex bolt head outside Wall Fig 21 Fig 22 CAUTION: Do not over tighten. 9 Unscrew and remove only the hex bolt. Leave the expansion sleeve inside the hole.
INSTALLATION INSTALLING CEILING BRACKETS Roof, eave or overhang 1 2 Optional parts available for purchase. 1 Locate a straight, flat and leveled edge of your roof, eave or overhang that is clear and free of obstructions. 2 Using a chalk line or laser level, mark a line that runs the entire length of your awning. Minimum 10 inch clear space Chalkliner Fig 27 Roof, eave or overhang 3 NOTE: The awning will stand 10” off of this line. 3 Place the ceiling brackets in the appropriate locations.
INSTALLATION 6 Place brackets over the appropriate holes. 7 Using a washer and a lag screw, secure the brackets to the surface until snug. 8 Attach wall bracket to the ceiling bracket using the provided bolts, washers and nuts. 6 2 3 4 Wall mount to ceiling bolts Washer 7 Wall bracket Lag screw Ceiling bracket Fig 31 INSTALLING AWNING ONTO BRACKETS 1 8 Washer Fig 32 Nut 1 Nut Remove the bolts on the front of the wall brackets.
INSTALLATION READY YOUR AWNING 2 WARNING: Before removing the safety restraints, make sure no persons or objects are in front of the awning. Failure to do so could result in personal injury. 1 1 Position yourself under the awning. 2 Remove the safety restraints from the arms one at a time. Do not use a knife or blade to cut the restraints. Fig 34 OPERATION 1 2 Use the hand crank to open the awning fully then close it completely to test for proper operation.
OPERATION ADJUST AWNING PITCH NOTE: All Advaning awning models come with the Easy PitchTM adjustment system. 8-12ft awning models have two (2) Easy PitchTM loops for adjustment. 1 Open the awning. 2 With the aid of a helper, support the front bar of the awning while another person adjusts the pitch of the awning using the hand crank and the Easy PitchTM System. 3 4 8-12ft awning: 2 Easy PitchTM loops Fig 36 1 3 2 Front bar 5 Turn the hand crank to adjust the awning pitch up and down.
MAINTENANCE PROTECTING THE FABRIC FROM MILDEW Allow the awning fabric to fully dry before retracting. Doing so will help prevent mildew from growing and prolong the life of the fabric. If you must retract the awning while wet, open the awning as soon as the weather permits to allow the fabric to fully dry and remove any dirt deposits to preserve the fabric. CLEANING THE FABRIC Cleaning the awning regularly with mild soap and water will extend the life of the fabric and prevent the formation of mildew.
WARRANTY LIMITED WARRANTY AND CUSTOMER SERVICE LIMITED WARRANTY COVERS Advaning warrants all Advaning original products, sold and installed within the 50 states of the United States, to be free of defects of materials and workmanship. This warranty only applies to the original owner or purchaser of the product and is only effective on a basis for sixty (60) months or five (5) years from the date of purchase.
WARRANTY LIMITED WARRANTY AND CUSTOMER SERVICE Problems and Warranty Claims If you experience a problem with your Advaning product, please contact Advaning Customer Service over the phone Monday through Friday 9:00AM – 4:00PM Pacific Standard Time at 1-855-574-0158 or email us at service@advaning. com.
WARRANTY LIMITED WARRANTY AND CUSTOMER SERVICE What is Not Covered by the Advaning Limited Warranty This warranty is non-transferable and does not cover product purchases from the initial buyer to a third party. This warranty does not cover incidental damages, such as loss of time, loss of use, or installation costs of defective, repaired or replaced product. This warranty does not cover product that has been damaged or rendered defective as a result of: (a) Neglect, abuse or misuse.
CONTACT INFORMATION Sales & Technical Questions: techsupport@advaning.com Warranty Claim: service@advaning.com Toll Free (US): 855–574-0158 Fax: 877-310-3832 West Coast: 12282 Knott Street, Garden Grove, CA 92841 East Coast: 151 Airport Drive, Westminster, MD 21157 www.advaning.com OM_S Series_V01_R01.2015.09.
