Hardware Inst allat ion Guide Advant ageGPS.
Welcome Experience 4G LTE Evo, t he next evolut ion in GPS t racking. Advant age by Procon Analyt ics - w here aut om ot ive t elem at ics m eet s genuine analyt ics. Inst allat ion M ade Easy Tools needed for inst all: screw drivers, w ire st rippers and cut t ers, crim ping t ool and volt met er. Plus, you m ight w ant t o have t he follow ing handy: connect ors, velcro, and zip t ies. • M ake sure t here is not m et al above t he device as it m ay int erfere w it h t he signal.
Evo Wiring [POWER/SERIAL CABLE DIAGRAM] We’ve included a det achable w iring harness. Connect everyt hing before plugging harness int o t he Evo device. Black Wire: Gr ound – Connect t he gr ound wi r e t o t he vehi cl e chassi s (shoul d al ways be f i r st connection made.) Red Wire: 12 VDC Constant Power – Connect to a constant power source. Voltage should read 12V when the vehicle’s ignition line is in the off position.
ECM Starter Disable [DIAGRAM 1] If t he st art er is cont rolled by t he ECM (Engine Cont rol M odule), splice t he w ire t hat leads direct ly from t he ECM t o t he st art er. Note: Do not splice into the wire leading from ignition switch to the ECM. GREEN (Not In Use) RED = Ignit ion WHITE = St art er YELLOW = Input Note: Yellow wire connects to Yellow relay wire.
Starter Interrupter [OPTIONAL FEATURE – DIAGRAM 1] • Locat e and cut t he st art er w ire of t he vehicle. This w ire w ill only display 12VDC w hile t he vehicle is st art ing. • Connect yellow wire from the harness to the yellow wire of the starter interrupt relay. • Connect red w ire from t he st art er int errupt relay t o t he ignit ion sw it ch side of t he st art er w ire. • Connect w hit e w ire of t he st art er int errupt relay t o t he st art er side of t he st art er w ire.
Payment Reminder [OPTIONAL FEATURE] • Locat e a sw it ch ignit ion pow er w ire t hat reads 12V w hen t he vehicle’s ignit ion is in t he ON posit ion and 0 Volt s w hen t he vehicle ignit ion is in t he OFF posit ion. The ignit ion w ire ret ains 12V as t he vehicle is st art ing. • • Connect t he w hit e w ire from harness t o t he vehicles ignit ion w ire.
LED Troubleshooting [TECHNICAL DATA] Technical Data Operat ing Volt age 7V - 28V Pow er Consum pt ion 2.5 m A (st andby), 50 m A (act ive) Operat ing Tem perat ure -30 oC t o +75 oC St orage Tem perat ure -40 oC t o +85 oC Operat ion Hum idit y 20% t o 90% (non-condensing) Solid Green = Cellular Signal is OK Flashing Green = Searching Solid Red = GPS Signal is OK Flashing Flashing Red = Searching Note: The following LED behavior is indicative of an over-the-air update: • Solid Red (15 secs.
FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
If you have quest ions or would like t o have our t eam of expert s help you wit h your inst all, please: 1-800-553-7031 Support@AdvantageGPS.com AdvantageGPS.com/Knowledge-Center Advant ageGPS.
