User's Manual
Table Of Contents
- ADAM-2000 Series
- 1 Understanding Your System
- 1.1 Introduction
- Figure 1.1 ADAM-2000 Series System Architecture
- Figure 1.2 ADAM-2000 Series Outdoor Range Distance
- 1.1.1 IEEE 802.15.4 Wireless Standard
- 1.1.2 Wireless Sensor Network
- 1.1.3 Low-power Consumption and Battery-Powered Design
- 1.1.4 Sensor Embedded Design
- 1.1.5 Wireless Signal Indicator
- 1.1.6 Industrial Standard Modbus Protocol
- 1.1.7 SCADA Software Support
- 1.1.8 Advantech Software Alignment
- 1.2 Specifications
- 1.3 Dimensions
- 1.4 Mounting
- 1.5 Wiring & Connections
- 1.1 Introduction
- 2 Selecting Your Hardware
- 3 Installation Guide
- 4 Software Configuration Guide
- 4.1 System Software Configuration Utility
- 4.2 Installing ADAM.NET Utility Software
- 4.3 ADAM.NET Utility Operation
- Figure 4.1 ADAM.NET Utility Operation Window
- Figure 4.2 ADAM.NET Utility Toolbar
- 4.3.1 Search and Configure the ADAM-2000 Series
- Figure 4.3 ADAM-2000 Series ADAM .NET Utility Support
- Figure 4.4 Search the USB interface ADAM-2000 devices on the host PC for the virtual COM port.
- Figure 4.5 Search the COM port for the ADAM-2000 devices.
- Figure 4.6 Searching the network dialog
- Figure 4.7 Searching the ADAM-2000 coordinators.
- Figure 4.8 ADAM-2000 devices lists on the Tree View and Information page.
- Figure 4.9 The overview of ADAM-2000 end devices.
- Figure 4.10 The overview of ADAM-2000 routers
- 4.3.1.1 Gateway - ADAM-2520Z
- 4.3.1.2 Router - ADAM-2510Z
- 4.3.1.3 End Device - ADAM-2017, ADAM-2031Z, ADAN-2051Z, ADAM-2051PZ
- Figure 4.16 Information Page of ADAM-2051Z
- Figure 4.17 Wireless Configuration page of ADAM-2051Z
- Figure 4.18 The Device Status page of the ADAM-2051Z
- Figure 4.19 The Signal page of the ADAM-2051Z
- Figure 4.20 Information Page
- Figure 4.21 Wireless Configuration Page
- Figure 4.22 Device Status Page
- Figure 4.23 Sensor Page
- 4.3.2 Network Topology of ADAM-2000 Series
- A Module Introduction
- B ADAM-2000 Series Functions
- C Troubleshooting
- 1 Understanding Your System
21 ADAM-2000 Series User Manual
Chapter 3 Installation Guide
3.2.1.2 Router/End Device
Routers and End Devices must have to associate with corresponding Pair ID Coordi-
nator in Initial Mode to build up the wireless communication. The function is for
Router and End Devices only.
1. Power on.
2. All LEDs turn on for 0.5 second then turn off.
3. Press the Function Button 3 times to join a PAN with the default Pair ID 1.
4. Status LED turns on, Error LED blinks.
5. Level Index turns on to indicate Pair ID 1. (Pair ID needs to be properly
configured if there are coordinators. For advanced settings, please refer to sec-
tion 3.3)
6. If the Coordinator Pair ID is not 1, hold the Function Button for 2 seconds to
reboot your router or end-devices, then press Function Button 5 times to enter
Pair ID selection, the click N times according the Coordinator Pair ID, then hold
the Function Button for 2 seconds to confirm your setting, finally press the
Function Button 3 times to join a PAN.
7. Error LED turns off when it join a PAN.