User's Manual
Table Of Contents
- ADAM-2000 Series
- 1 Understanding Your System
- 1.1 Introduction
- Figure 1.1 ADAM-2000 Series System Architecture
- Figure 1.2 ADAM-2000 Series Outdoor Range Distance
- 1.1.1 IEEE 802.15.4 Wireless Standard
- 1.1.2 Wireless Sensor Network
- 1.1.3 Low-power Consumption and Battery-Powered Design
- 1.1.4 Sensor Embedded Design
- 1.1.5 Wireless Signal Indicator
- 1.1.6 Industrial Standard Modbus Protocol
- 1.1.7 SCADA Software Support
- 1.1.8 Advantech Software Alignment
- 1.2 Specifications
- 1.3 Dimensions
- 1.4 Mounting
- 1.5 Wiring & Connections
- 1.1 Introduction
- 2 Selecting Your Hardware
- 3 Installation Guide
- 4 Software Configuration Guide
- 4.1 System Software Configuration Utility
- 4.2 Installing ADAM.NET Utility Software
- 4.3 ADAM.NET Utility Operation
- Figure 4.1 ADAM.NET Utility Operation Window
- Figure 4.2 ADAM.NET Utility Toolbar
- 4.3.1 Search and Configure the ADAM-2000 Series
- Figure 4.3 ADAM-2000 Series ADAM .NET Utility Support
- Figure 4.4 Search the USB interface ADAM-2000 devices on the host PC for the virtual COM port.
- Figure 4.5 Search the COM port for the ADAM-2000 devices.
- Figure 4.6 Searching the network dialog
- Figure 4.7 Searching the ADAM-2000 coordinators.
- Figure 4.8 ADAM-2000 devices lists on the Tree View and Information page.
- Figure 4.9 The overview of ADAM-2000 end devices.
- Figure 4.10 The overview of ADAM-2000 routers
- 4.3.1.1 Gateway - ADAM-2520Z
- 4.3.1.2 Router - ADAM-2510Z
- 4.3.1.3 End Device - ADAM-2017, ADAM-2031Z, ADAN-2051Z, ADAM-2051PZ
- Figure 4.16 Information Page of ADAM-2051Z
- Figure 4.17 Wireless Configuration page of ADAM-2051Z
- Figure 4.18 The Device Status page of the ADAM-2051Z
- Figure 4.19 The Signal page of the ADAM-2051Z
- Figure 4.20 Information Page
- Figure 4.21 Wireless Configuration Page
- Figure 4.22 Device Status Page
- Figure 4.23 Sensor Page
- 4.3.2 Network Topology of ADAM-2000 Series
- A Module Introduction
- B ADAM-2000 Series Functions
- C Troubleshooting
- 1 Understanding Your System
51 ADAM-2000 Series User Manual
Appendix A Module Introduction
A.2.2 ADAM-2031Z
Wireless Sensor Network Temperature and Humidity Sensor Node
The ADAM-2031 is an end device embedded sensors to measure the temperature
and humidity physical signal.
A.2.2.1 Specifications
Wireless:
IEEE Standard: IEEE 802.15.4
Modulation Type: DSSS (OQPSK)
Frequency Band: ISM 2.4GHz (2.4 GHz ~ 2.4835 GHz)
Channels: 11-26
RF Data Rate: 250 Kbps
Transmit Power: 3±1 dBm
Receiver Sensitivity: -97dBm
Antenna Type: Dipole
Antenna Gain:0 dBi
Outdoor Range: 200 m
Transmission Interval: 1 second ~ 24 hours
Function: End Device
General:
Connector: 1x plug-in terminal block (#14-22 AWG)
Power Input: Unregulated10 ~ 30 V
DC
Battery Input: 2 x AA Alkaline
Power Consumption:
– 0.3 W @ 24 V
DC
– 420 uW @ 3 V
DC
(1 minute Tx interval with 2* AA Batteries)
– 240 uW @ 3 V
DC
(2 minute Tx interval with 2* AA Batteries)
– 150 uW @ 3 V
DC
(5 minute Tx interval with 2* AA Batteries)
Operating Humidity: 20 ~ 95% RH (non-condensing)
Storage Humidity: 0 ~ 95% RH
Operating Temperature:-20°C ~ 70°C (-4°F ~ 157.9°F)
Storage Temperature: -20°C ~ 70°C (-4°F ~ 157.9°F)
Temperature Sensor Input
Operating Range -40~85°C (-40 ~ 185°F)
Resolution 0.02°C (0.04°F)
Accuracy ±0.3°C (0.6°F)
Repeatability ±0.1°C (0.4°F)
Response Time 5 ~ 30 seconds (Achieving 63% of a step function)
Long Term Drift < 0.04°C/Year (0.07°F/Year)
Humidity Sensor Input
Operating Range 0 ~ 100% RH
Resolution 0.15% RH
Accuracy ±2.0% RH
Repeatability ±0.1% RH
Response Time 8 seconds (Achieving 63% of a step function)
Long Term Drift 0.5% RH/Year