User's Manual
Table Of Contents
- ADAM-2000 Series
- 1 Understanding Your System
- 1.1 Introduction
- Figure 1.1 ADAM-2000 Series System Architecture
- Figure 1.2 ADAM-2000 Series Outdoor Range Distance
- 1.1.1 IEEE 802.15.4 Wireless Standard
- 1.1.2 Wireless Sensor Network
- 1.1.3 Low-power Consumption and Battery-Powered Design
- 1.1.4 Sensor Embedded Design
- 1.1.5 Wireless Signal Indicator
- 1.1.6 Industrial Standard Modbus Protocol
- 1.1.7 SCADA Software Support
- 1.1.8 Advantech Software Alignment
- 1.2 Specifications
- 1.3 Dimensions
- 1.4 Mounting
- 1.5 Wiring & Connections
- 1.1 Introduction
- 2 Selecting Your Hardware
- 3 Installation Guide
- 4 Software Configuration Guide
- 4.1 System Software Configuration Utility
- 4.2 Installing ADAM.NET Utility Software
- 4.3 ADAM.NET Utility Operation
- Figure 4.1 ADAM.NET Utility Operation Window
- Figure 4.2 ADAM.NET Utility Toolbar
- 4.3.1 Search and Configure the ADAM-2000 Series
- Figure 4.3 ADAM-2000 Series ADAM .NET Utility Support
- Figure 4.4 Search the USB interface ADAM-2000 devices on the host PC for the virtual COM port.
- Figure 4.5 Search the COM port for the ADAM-2000 devices.
- Figure 4.6 Searching the network dialog
- Figure 4.7 Searching the ADAM-2000 coordinators.
- Figure 4.8 ADAM-2000 devices lists on the Tree View and Information page.
- Figure 4.9 The overview of ADAM-2000 end devices.
- Figure 4.10 The overview of ADAM-2000 routers
- 4.3.1.1 Gateway - ADAM-2520Z
- 4.3.1.2 Router - ADAM-2510Z
- 4.3.1.3 End Device - ADAM-2017, ADAM-2031Z, ADAN-2051Z, ADAM-2051PZ
- Figure 4.16 Information Page of ADAM-2051Z
- Figure 4.17 Wireless Configuration page of ADAM-2051Z
- Figure 4.18 The Device Status page of the ADAM-2051Z
- Figure 4.19 The Signal page of the ADAM-2051Z
- Figure 4.20 Information Page
- Figure 4.21 Wireless Configuration Page
- Figure 4.22 Device Status Page
- Figure 4.23 Sensor Page
- 4.3.2 Network Topology of ADAM-2000 Series
- A Module Introduction
- B ADAM-2000 Series Functions
- C Troubleshooting
- 1 Understanding Your System
ADAM-2000 Series User Manual 24
3.2.2.2 Coordinator Configuration Flowchart
The section tells the user how to setup the Coordinator to host a PAN for a wireless
sensor network.
Please refer to
Appendix C for
troubleshooting.
Please refer to
Appendix C for
troubleshooting.
Install Power
Connect to PC through
USB or RS-422/485
All LEDs turn On
(Green LED turns on while powering by
external/USB power)
Configured ready for
Normal Mode
Initial Mode:
Status LED turns on,
Error LED blinks.
Normal Mode:
Status LED turns off,
Error LED blinks.
Error LED turns off
Successfully host a
PAN with default PAN
ID and RF channel then
Amber LED turns on
indicating Pair ID.
Successfully host a
PAN with user defined
PAN ID and RF channel
then Amber LED turns
on indicating Modbus
ID.
Open ADAM .NET
Utility to configure the
ADAM-2000 series,
please refer to the
chapter 4 for more
information.
Collect and transmit
data/signal from end
nodes to host.
Error LED turns off
No Yes
No
No
Yes
Yes