User's Manual
Table Of Contents
- ADAM-2000 Series
- 1 Understanding Your System
- 1.1 Introduction
- Figure 1.1 ADAM-2000 Series System Architecture
- Figure 1.2 ADAM-2000 Series Outdoor Range Distance
- 1.1.1 IEEE 802.15.4 Wireless Standard
- 1.1.2 Wireless Sensor Network
- 1.1.3 Low-power Consumption and Battery-Powered Design
- 1.1.4 Sensor Embedded Design
- 1.1.5 Wireless Signal Indicator
- 1.1.6 Industrial Standard Modbus Protocol
- 1.1.7 SCADA Software Support
- 1.1.8 Advantech Software Alignment
- 1.2 Specifications
- 1.3 Dimensions
- 1.4 Mounting
- 1.5 Wiring & Connections
- 1.1 Introduction
- 2 Selecting Your Hardware
- 3 Installation Guide
- 4 Software Configuration Guide
- 4.1 System Software Configuration Utility
- 4.2 Installing ADAM.NET Utility Software
- 4.3 ADAM.NET Utility Operation
- Figure 4.1 ADAM.NET Utility Operation Window
- Figure 4.2 ADAM.NET Utility Toolbar
- 4.3.1 Search and Configure the ADAM-2000 Series
- Figure 4.3 ADAM-2000 Series ADAM .NET Utility Support
- Figure 4.4 Search the USB interface ADAM-2000 devices on the host PC for the virtual COM port.
- Figure 4.5 Search the COM port for the ADAM-2000 devices.
- Figure 4.6 Searching the network dialog
- Figure 4.7 Searching the ADAM-2000 coordinators.
- Figure 4.8 ADAM-2000 devices lists on the Tree View and Information page.
- Figure 4.9 The overview of ADAM-2000 end devices.
- Figure 4.10 The overview of ADAM-2000 routers
- 4.3.1.1 Gateway - ADAM-2520Z
- 4.3.1.2 Router - ADAM-2510Z
- 4.3.1.3 End Device - ADAM-2017, ADAM-2031Z, ADAN-2051Z, ADAM-2051PZ
- Figure 4.16 Information Page of ADAM-2051Z
- Figure 4.17 Wireless Configuration page of ADAM-2051Z
- Figure 4.18 The Device Status page of the ADAM-2051Z
- Figure 4.19 The Signal page of the ADAM-2051Z
- Figure 4.20 Information Page
- Figure 4.21 Wireless Configuration Page
- Figure 4.22 Device Status Page
- Figure 4.23 Sensor Page
- 4.3.2 Network Topology of ADAM-2000 Series
- A Module Introduction
- B ADAM-2000 Series Functions
- C Troubleshooting
- 1 Understanding Your System
33 ADAM-2000 Series User Manual
Chapter 4 Software Configuration Guide
4.3.1 Search and Configure the ADAM-2000 Series
The ADAM-2000 series can be searched and configured through ADAM .NET Utility.
Make sure the ADAM-2000 devices are installed properly in Initial Mode. For more
information, please refer to the section 3.4.
The supported Wireless Sensor Networks Modules are listed in the information page
.
Figure 4.3 ADAM-2000 Series ADAM .NET Utility Support
If the user wants to use USB cable to connection with ADAM utility on PC, they need
to install USB chip driver in CD.
Step 1
Connect a USB cable between the ADAM-2520Z and the PC, and the system will
pop out message to install new device, find the USB folder to select USB chip driver
in out CD.
Base on your PC for 32 bit or 64 bit to select your suitable USB chip driver, then PC
will auto install. After install finished, you can see which port your system get in
device manager like bellow one. (Note: base on your system, this picture just for
sample)
Then restart the ADAM utility.