User Manual ARK-1122 Fanless Embedded Box PC
Attention! This package contains a hard-copy user manual in Chinese for China CCC certification purposes, and there is an English user manual included as a PDF file on the CD. Please disregard the printed Chinese copy of the user manual if the product is not to be sold and/or installed in China.
Copyright The documentation and the software included with this product are copyrighted 2013 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Technical Support and Assistance 1. 2. Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. Keep this equipment away from humidity.
The sound pressure level at the operator's position according to IEC 704-1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
ARK-1122 User Manual viii
Contents Chapter 1 General Introduction ...........................1 1.1 1.2 1.3 Introduction ............................................................................................... 2 Features .................................................................................................... 2 Specifications ............................................................................................ 2 1.3.1 General ................................................................................
2.4.8 2.5 2.6 2.7 Chapter HDMI Connector ......................................................................... 15 Figure 2.14 HDMI Connector..................................................... 15 ARK-1122C External I/O Connectors ..................................................... 15 2.5.1 Power ON/OFF Button................................................................ 15 Figure 2.15 Power ON/OFF Button ........................................... 15 2.5.2 Power Input Connector ...............
3.2.3 3.2.4 3.2.5 3.2.6 Figure 3.3 Advanced BIOS Features Setup Screen ................ 32 Figure 3.4 ACPI Setting ........................................................... 33 Figure 3.5 CPU Configuration Settings.................................... 34 Figure 3.6 IDE Configuration ................................................... 35 Figure 3.7 Intel Fast Flash Standby......................................... 36 Figure 3.8 USB Configuration.................................................. 37 Figure 3.
ARK-1122 User Manual xii
Chapter 1 1 General Introduction This chapter gives background information on ARK-1122 series.
1.1 Introduction The ARK-1122 fanless Embedded Box Computer is an ideal, application-ready system platform solution. All electronics are protected in a compact, sealed, aluminum case for easy embedding in the customer’s own housing, or as a stand-alone application where space is limited and the environment harsh. The solid, sealed aluminum case offers vibration and dust resistance while also providing a passive cooling solution.
1.3.2 Display Chipset: Intel® Atom N2600/N2800 Display Memory: Intel® NM10 Express Chipset VGA Resolution: Supports up to 1920 x 1200 HDMI Chipset: Intel® 82567V Speed: 10/100/1000 Mbps, support Wake on LAN Interface: Up to 2 x RJ45 (ARK-1122F) Standard: Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3x, IEEE 8023y, IEEE 802.ab. 1.3.4 Power Consumption Input Voltage: DC 12V Power Adapter: AC to DC 12 V/3 A, 36 W 1.3.
1.5 Mechanical Specifications 1.5.1 ARK-1122H Dimensions Figure 1.
Chapter 1 1.5.2 ARK-1122C Dimensions General Introduction Figure 1.
1.5.3 ARK-1122F Dimensions Figure 1.
Chapter 2 2 Hardware installation This chapter introduces external IO and the installation of ARK-1122 Hardware.
2.1 Introduction The following sections show the internal jumper settings and the external connectors and pin assignments for applications. 2.2 Jumpers 2.2.1 Jumper list Table 2.1: Jumper List J1 AT / ATX Power Selection 2.2.2 Jumper Settings Table 2.2: J1: AT / ATX Power Selection Part Number 1653003260 Footprint HD_3x2P_79 Description PIN HEADER 3*2P 180D(M) 2.0mm SMD SOUARE PIN Setting Function (5-6) ON AT power *(5-6) Empty ATX power * Default setting 2.2.
Warning! To avoid damaging the computer, always turn off the power supply before setting jumpers or clearing CMOS. Before turning on the power supply, make sure CMOS jumper is back to 3.0 V Battery On. Chapter 2 Generally, you simply need a standard cable to make most connections. 2.3 ARK-1122 I/O Indication Hardware installation ARK-1122H Figure 2.1 ARK-1122H front view Figure 2.
ARK-1122C Figure 2.3 ARK-1122C front view Figure 2.
Chapter 2 ARK-1122F Hardware installation Figure 2.5 ARK-1122F front view Figure 2.
2.4 ARK-1122H External I/O Connectors 2.4.1 Power ON/OFF Button ARK-1122H comes with a Power On/Off button with LED indicators on the front side to show its On status (Green LED) and Off/Suspend status (Orange LED). Dual functions of Soft Power -On/Off (Instant off or Delay 4 Seconds), and Suspend are supported. Figure 2.7 Power ON/OFF Button 2.4.2 Power Input Connector ARK-1122H comes with a DC-Jack header that carries 12 VDC external power input. The bracket makes the power connector very secure.
NC, if present, means “No Connection”. 2.4.4 VGA Connector The ARK-1122H provides a high resolution VGA interface connected by a D-sub 15pin connector to support a VGA CRT monitor. It supports display resolution up to 1920 x 1200 HDMI. 1 6 11 Figure 2.10 VGA Connector Table 2.4: VGA Connector Pin Assignments Pin Signal Name Pin Signal Name 1 Red 2 Green 3 Blue 4 NC 5 GND 6 GND 7 GND 8 GND 9 NC 10 GND 11 NC 12 DDC Date 13 H-SYNC 14 V-SYNC 15 DDC Clock 2.4.
2.4.6 Audio Connector ARK-1122H offers stereo audio ports by two 3.5 ear phone jack connectors of Line_out and Line_in. The audio chip controller is ALC892 which is compliant with the Azalea standard. 1 2 Figure 2.12 Audio Connector Table 2.6: DIO Connector Pin Assignments Pin Signal Name 1 Line-out 2 Line-in 2.4.7 COM Connector ARK-1122H provides one D-sub 9-pin connectors, which offers RS-232 serial communication interface. Figure 2.13 COM Port Connector Table 2.
An integrated, 19-pin receptacle connector HDMI Type A Interface is provided. The HDMI link supports resolutions up to 1920x1200 @ 60 Hz. 2.5 ARK-1122C External I/O Connectors 2.5.1 Power ON/OFF Button ARK-1122C comes with a Power On/Off button with LED indicators on the front side to show its On status (Green LED) and Off/Suspend status (Orange LED). Dual functions of Soft Power -On/Off (Instant off or Delay 4 Seconds), and Suspend are supported. Figure 2.15 Power ON/OFF Button 2.5.
Table 2.8: Ethernet Connector Pin Assignments Pin 10/100/1000 Mbps Signal Name 1 TX+, MDI0+ 2 TX-, MDI0- 3 RX+, MDI1+ 4 MDI2+ 5 MDI2- 6 RX-, MDI1- 7 MDI3+ 8 MDI3- Note! NC, if present, means “No Connection”. 2.5.4 VGA Connector The ARK-1122C provides a high resolution VGA interface connected by a D-sub 15pin connector to support a VGA CRT monitor. It supports display resolution up to 1920 x 1200 HDMI. 5 10 15 1 6 11 Figure 2.18 VGA Connector Table 2.
The ARK-1122C provides up to four USB interface connectors, which give complete Plug & Play and hot swapping for up to 127 external devices. The USB interface is compliant with USB UHCI, Rev. 2.0. The USB interface supports Plug and Play, which enables you to connect or disconnect a device whenever you want, without turning off the computer. Table 2.10: USB Connector Pin Assignments Pin Signal Name Pin Signal Name 1 VCC 2 USB_data- 3 USB_data+ 4 GND 2.5.
2.5.7 COM Connector ARK-1122C provides four D-sub 9-pin connectors, which offers two RS-232 serial communication interface and two RS-232/422/485 serial communication interface. Default setting is RS-232, and the mode of serial ports are controlled by relay IC. If you would like to use RS-422/485, just need change the BIOS setting. You can find detailed BIOS setting for serial ports in Chapter 3. Figure 2.21 COM Port Connector Table 2.
2.6.1 Power ON/OFF Button ARK-1122F comes with a Power On/Off button with LED indicators on the front side to show its On status (Green LED) and Off/Suspend status (Orange LED). Dual functions of Soft Power -On/Off (Instant off or Delay 4 Seconds), and Suspend are supported. 2.6.2 Power Input Connector ARK-1122F comes with a DC-Jack header that carries 12 VDC external power input. The bracket makes the power connector very secure. Figure 2.23 Power Input Connector 2.6.
Note! NC, if present, means “No Connection”. 2.6.4 VGA Connector The ARK-1122F provides a high resolution VGA interface connected by a D-sub 15pin connector to support a VGA CRT monitor. It supports display resolution up to 1920 x 1200 HDMI. 5 10 15 1 6 11 Figure 2.25 VGA Connector Table 2.14: VGA Connector Pin Assignments Pin Signal Name Pin Signal Name 1 Red 2 Green 3 Blue 4 NC 5 GND 6 GND 7 GND 8 GND 9 NC 10 GND 11 NC 12 DDC Date 13 H-SYNC 14 V-SYNC 15 DDC Clock 2.
ARK-1122F offers stereo audio ports by two 3.5 ear phone jack connectors of Line_out and Line_in. The audio chip controller is ALC892 which is compliant with the Azalea standard. 1 2 Table 2.16: DIO Connector Pin Assignments Pin Signal Name 1 Line-out 2 Line-in 2.6.7 COM Connector ARK-1122F provides one D-sub 9-pin connectors, which offers RS-232 serial communication interface. Figure 2.28 COM Port Connector Table 2.
2.6.8 HDMI Connector An integrated, 19-pin receptacle connector HDMI Type A Interface is provided. The HDMI link supports resolutions up to 1920 x 1200 @ 60 Hz. Figure 2.29 HDMI Connector 2.6.9 SIM Card Holder ARK-1122F provides a SIM card Holder for internet connection. Figure 2.30 SIM Card Holder 2.7 Peripheral Installation 2.7.1 HDD Installation (ARK-1122H only) 1. Unscrew the bottom cover screws.
Remove the four SNAP RIVETs from the bottom cover. 3. Secure 2.5" SATA HDD onto the bottom cover. The screws are in the accessory box. ARK-1122 User Manual Hardware installation 23 Chapter 2 2.
4. Connect SATA signal and power cable to the 2.5" SATA HDD.
Secure the bottom cover in its original position. Chapter 2 5. ** Below installation is for ARK-1122H & ARK-1122C only. For ARK-1122F, we suggest to install by CTOS due to complex installation 1. Unscrew the bottom cover screws. 25 ARK-1122 User Manual Hardware installation 2.7.
2. Insert mSATA storage into the slot and secure the screw to fix the mSATA storage. 3. Secure the original screw.
Unscrew the four screws on bottom cover. (marked with "RAM") 2. Unscrew the four screws on the sides of ARK-1122. 27 Hardware installation 1. Chapter 2 2.7.
3. Unscrew the four screws on the front/rear face plate of ARK-1122. 4. Remove aluminum top chassis and install RAM. 5. Replace the aluminum top chassis and secure all screws.
Chapter 3 3 BIOS Settings This chapter introduces how to set BIOS configuration data.
3.1 Introduction AMIBIOS has been integrated into a plethora of motherboards for a couple decades. With the AMIBIOS Setup program, users can modify BIOS settings and control various system features. This chapter describes the basic navigation of the ARK-1122 BIOS setup screens. Figure 3.1 Setup program initial screen AMI's BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration.
Turn on the computer and then press or to enter Setup menu. 3.2.1 Main Setup When users first enter the BIOS Setup Utility, users will enter the Main setup screen. Users can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below. Chapter 3 3.2 Entering Setup BIOS Settings Figure 3.2 Main Setup Screen The Main BIOS setup screen has two main frames.
3.2.2 Advanced BIOS Features Setup Select the Advanced tab from the ARK-1122 setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the keys, and smacking . All Advanced BIOS Setup options are described in this section. The Advanced BIOS Setup screens are shown below.
Chapter 3 3.2.2.1 ACPI Settings BIOS Settings Figure 3.4 ACPI Setting Enable ACPI Auto Configuration This item allows users to enable or disable BIOS ACPI auto configuration. ACPI Sleep State This item allows users to set the ACPI sleep state. Lock Legacy Resources This item allows users to lock legacy devices' resources. S3 Video Repost This item allows users to enable or disable VBIOS run after S3 resume.
3.2.2.2 CPU Configuration Figure 3.5 CPU Configuration Settings Hyper-Threading This item allows you to enable or disable Intel® Hyper Threading technology. Execute Disable Bit This item allows you to enable or disable the No-Execution page protection technology. Limit CPUID Maximum This item allows you to limit CPUID maximum value.
Chapter 3 3.2.2.3 IDE Configuration BIOS Settings Figure 3.6 IDE Configuration SATA Controller This item allows users to enable or disable the SATA controller.
3.2.2.4 Intel Fast Flash Standby Figure 3.7 Intel Fast Flash Standby IFFS Support This item allows users to enable or disable IFFS support.
Chapter 3 3.2.2.5 USB Configuration BIOS Settings Figure 3.8 USB Configuration Legacy USB Support Enable the support for legacy USB. Auto option disables legacy support if no USB devices are connected. EHCI Hand-Off This is a workaround for the OS without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver. USB transfer time-out Set the time-out value for Control, Bulk, and Interrupt transfers.
3.2.2.6 Super IO Configuration Figure 3.9 Super IO Configuration Serial Port 1 configuration This item allows you to select serial port1 configuration. Serial Port 2 - 4 configuration (ARK-1122C only) This item allows you to select serial port 2 ~ 4 configuration. Serial port3 and port4 can be set as RS-232/RS-422/RS-485. The default setting is RS-232. WatchDog function This item allows you to enable WatchDog function, in minutes or seconds.
Chapter 3 3.2.2.7 H/W Monitor BIOS Settings Figure 3.10 H/W Monitor Temperature & Voltage show CPU / System Temperature / VBAT / Current / +5.
3.2.2.8 AOAC Configuration Figure 3.11 AOAC Configuration AOAC Configuration This item allows users to enable or disable AOAC Configuration.
Chapter 3 3.2.2.9 PPM Configuration BIOS Settings Figure 3.12 PPM Configuration EIST CPU runs at its default speed if disabled; CPU speed is controlled by the operating system if enabled. CPU C State Report This item allows users to enable or disable CPU C state report. Enhanced C State This item allows users to enable or disable enhanced C state. CPU Hard C4E This item allows users to enable or disable CPU hard C4E CPU C6 State This item allows users to enable or disable CPU C6 state.
3.2.3 Chipset Figure 3.13 Chipset Setup 3.2.3.1 Host Bridge Figure 3.
Auto Disable IGD This item allows user to enable/disable auto disable IGD IGFX - Boot Type This item allows user to select IGFX boot type. IGD - Clock Source This item allows user to select IGD-clock source ALS Support This item allows user to enable/disable ALS support Chapter 3 BIOS Settings 3.2.3.2 South Bridge Figure 3.15 Chipset Setup DMI Link ASPM Control This item allows users to enable/disable DMI link ASPM control.
3.2.4 Boot Figure 3.16 Boot Setup Setup Prompt Timeout This item allows users to select the number of seconds to wait for setup activation key. Bootup NumLock State Select the Power-on state for Numlock. Quiet Boot If this option is set to Disabled, the BIOS displays normal POST messages. If Enabled, an OEM Logo is shown instead of POST messages. Option ROM Message Set display mode for option ROM. Interrupt 19 Capture This item allows option ROMs to trap interrupt 19.
Chapter 3 3.2.5 Security Settings BIOS Settings Figure 3.17 Security Setup Select Security Setup from the ARK-1122 Setup main BIOS setup menu. All Security Setup options, such as password protection and virus protection are described in this section. To access the sub menu for the following items, select the item and press : Administrator Password This item allows user to set up password for protection.
3.2.6 Save & Exit Figure 3.18 Save & Exit Setup Save Changes and Exit When users have completed system configuration, select this option to save changes, exit BIOS setup menu and reboot the computer if necessary to take effect all system configuration parameters. Discard Changes and Exit Select this option to quit Setup without making any permanent changes to the system configuration.
Save User Defaults When users have completed system configuration, select this option to save changes as user defaults without exit BIOS setup menu. Restore User Defaults The users can select this option to restore user defaults.
ARK-1122 User Manual 48
Appendix A A WDT Sample Code
A.1 Watchdog Timer Sample Code Watchdog function: ;The SCH3114 Runtime base I/O address is A00h ;Setting WatchDog time value location at offset 66h ;If set value "0", it is mean disable WatchDog function. Superio_GPIO_Port = A00h mov dx,Superio_GPIO_Port + 66h mov al,00h out dx,al .model small .486p .stack 256 .data SCH3114_IO EQU A00h .code org 100h .
51 ARK-1122 User Manual Appendix A WDT Sample Code ;WD timer counting = 0 ;==================================================== mov dx,SCH3114_IO + 68h mov al,01h out dx,al .
ARK-1122 User Manual 52
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
