User manual
Table Of Contents
- ARK-3399
- 1 General Introduction
- 2 H/W installation
- 2.1 Introduction
- 2.2 Jumpers
- 2.3 Connectors
- Figure 2.2 ARK-3389 IO connectors drawing
- 2.3.1 ARK-3399 external I/O connectors
- 2.3.1.1 COM Connectors
- 2.3.1.2 Ethernet Connector (LAN)
- 2.3.1.3 PS2 Keyboard/Mouse Connector
- 2.3.1.4 VGA Connector
- 2.3.1.5 USB Connector
- 2.3.1.6 Power Input Connector
- 2.3.1.7 Power ON/OFF Button
- 2.3.1.8 LED Indicators
- 2.3.1.9 Audio Connector
- 2.3.1.10 DIO Connector
- 2.3.1.11 LVDS Connector
- 2.3.1.12 LCD Backlight On/Off control Connector
- 2.4 Installation
- 3 BIOS Operation
- 3.1 BIOS Introduction
- 3.2 BIOS Setup
- 3.2.1 Main Menu
- 3.2.2 Standard CMOS Features
- 3.2.3 Advanced BIOS Features
- 3.2.4 Advanced Chipset Features
- 3.2.5 Integrated Peripherals
- 3.2.6 Power Management Setup
- 3.2.7 PnP/PCI Configurations
- 3.2.8 PC Health Status
- 3.2.9 Frequency/Voltage Control
- 3.2.10 Load Optimized Defaults
- 3.2.11 Set Password
- 3.2.12 Save & Exit Setup
- 3.2.13 Quit Without Saving
- 4 Full Disassembly Procedure
- 4.1 Introduction
- Figure 4.1 Unscrew the bottom screws
- Figure 4.2 Unscrew the frame screws and remove the frame
- Figure 4.3 Unscrew the panel screws
- Figure 4.4 Unscrew the hex-bolts on the panel
- Figure 4.5 Unscrew the ground wire of LVDS cable and disconnect all the cables and boards
- Figure 4.6 Unscrew the boards’ screws and hex-bolts for disassembly
- Figure 4.7 Unscrew the power module screws on the bottom to disassemble the power module
- 4.1 Introduction
ARK-3399 User Manual 16
2.3.1.11 LVDS Connector
The ARK-3399 comes with a D-Sub 26-pin connector that carries LVDS signal out-
put, and can direct connect to LVDS LCD Display via external cable.
The system also provide a jumper of J2 on internal motherboard for selecting the
LCD signal power of 5V or 3.3V, please refer to the jumper table of J2, and “Full Dis-
assembly Procedure” to adjust it. Up. The default setting of J2 is 3.3V.
Figure 2.11 LVDS Connector
2.3.1.12 LCD Backlight On/Off control Connector
The ARK-3399 comes with a D-Sub 9-pin connector which provides BKLTEN signal
as well as +12 V, +5 V and Ground Pin signals that allow the user to connect these
signals to LCD Inverter to implement the LCD On/Off control.
Provides BKLTEN signal that inverter Module requires for inverter on/off control
Provides 12 V, 5 V as the Inverter Power Source. The additional VBR signal pin
could be connected to LCD’s Inverter that allow the user to achieve brightness
adjustment through customer’s software utility.
Figure 2.12 LCD Backlight connector
Table 2.11: LVDS Connector Pin Assignment
Pin Signal Name Pin Signal name
1 LVDS_CLKBP 14 LVDS_CLKBM
2 GND 15 LVDS_YAM0
3 LVDS_YAP0 16 LVDS_YAM1
4 LVDS_YAP1 17 LVDS_YAM2
5 LVDS_YAP2 18 LVDS_CLKAM
6 LVDS_CLKAP 19 GND
7 +3.3 or +5 V 20 +3.3 or +5 V
8 GND 21 LVDS_YAM3
9 LVDS_YAP3 22 LVDS_YBM0
10 LVDS_YBP0 23 LVDS_YBM1
11 LVDS_YBP1 24 LVDS_YBM2
12 LVDS_YBP2 25 LVDS_YBM3
13 LVDS_YBP3 26 GND
15
9
6
324
78