User manual
Table Of Contents
- ARK-3399
- 1 General Introduction
 - 2 H/W installation
- 2.1 Introduction
 - 2.2 Jumpers
 - 2.3 Connectors
- Figure 2.2 ARK-3389 IO connectors drawing
 - 2.3.1 ARK-3399 external I/O connectors
- 2.3.1.1 COM Connectors
 - 2.3.1.2 Ethernet Connector (LAN)
 - 2.3.1.3 PS2 Keyboard/Mouse Connector
 - 2.3.1.4 VGA Connector
 - 2.3.1.5 USB Connector
 - 2.3.1.6 Power Input Connector
 - 2.3.1.7 Power ON/OFF Button
 - 2.3.1.8 LED Indicators
 - 2.3.1.9 Audio Connector
 - 2.3.1.10 DIO Connector
 - 2.3.1.11 LVDS Connector
 - 2.3.1.12 LCD Backlight On/Off control Connector
 
 
 - 2.4 Installation
 
 - 3 BIOS Operation
- 3.1 BIOS Introduction
 - 3.2 BIOS Setup
- 3.2.1 Main Menu
 - 3.2.2 Standard CMOS Features
 - 3.2.3 Advanced BIOS Features
 - 3.2.4 Advanced Chipset Features
 - 3.2.5 Integrated Peripherals
 - 3.2.6 Power Management Setup
 - 3.2.7 PnP/PCI Configurations
 - 3.2.8 PC Health Status
 - 3.2.9 Frequency/Voltage Control
 - 3.2.10 Load Optimized Defaults
 - 3.2.11 Set Password
 - 3.2.12 Save & Exit Setup
 - 3.2.13 Quit Without Saving
 
 
 - 4 Full Disassembly Procedure
- 4.1 Introduction
- Figure 4.1 Unscrew the bottom screws
 - Figure 4.2 Unscrew the frame screws and remove the frame
 - Figure 4.3 Unscrew the panel screws
 - Figure 4.4 Unscrew the hex-bolts on the panel
 - Figure 4.5 Unscrew the ground wire of LVDS cable and disconnect all the cables and boards
 - Figure 4.6 Unscrew the boards’ screws and hex-bolts for disassembly
 - Figure 4.7 Unscrew the power module screws on the bottom to disassemble the power module
 
 
 - 4.1 Introduction
 
 

ARK-3399 User Manual vi
2.4.1 HDD Installation.......................................................................... 17
Figure 2.13Unscrew the HDD door screws ................................ 17
Figure 2.14Assemble HDD and HDD frame by 4 Screws .......... 18
Figure 2.15Screw on the HDD damper screws to assemble the 
HDD door and HDD frame ....................................... 18
Figure 2.16Connect the HDD cables.......................................... 19
2.4.2 Memory Installation..................................................................... 19
Figure 2.17Install the memory module into the SO-DIMM socket at 
the bottom of the Main board ................................... 19
2.4.3 CF card Installation..................................................................... 20
Figure 2.18Install the CF card into the CF slot at the bottom of the 
Main board ............................................................... 20
Chapter 3 BIOS Operation ................................. 21
3.1 BIOS Introduction.................................................................................... 22
3.2 BIOS Setup ............................................................................................. 22
3.2.1 Main Menu .................................................................................. 23
3.2.2 Standard CMOS Features .......................................................... 24
3.2.3 Advanced BIOS Features ........................................................... 25
3.2.4 Advanced Chipset Features ....................................................... 27
3.2.5 Integrated Peripherals ................................................................ 29
3.2.6 Power Management Setup ......................................................... 30
3.2.7 PnP/PCI Configurations.............................................................. 32
3.2.8 PC Health Status ........................................................................ 33
3.2.9 Frequency/Voltage Control ......................................................... 33
3.2.10 Load Optimized Defaults ............................................................ 34
3.2.11 Set Password.............................................................................. 35
3.2.12 Save & Exit Setup....................................................................... 36
3.2.13 Quit Without Saving .................................................................... 37
Chapter 4 Full Disassembly Procedure............ 39
4.1 Introduction ............................................................................................. 40
Figure 4.1 Unscrew the bottom screws ..................................... 40
Figure 4.2 Unscrew the frame screws and remove the frame... 40
Figure 4.3 Unscrew the panel screws ....................................... 41
Figure 4.4 Unscrew the hex-bolts on the panel ......................... 41
Figure 4.5 Unscrew the ground wire of LVDS cable and discon-
nect all the cables and boards.................................. 42
Figure 4.6 Unscrew the boards’ screws and hex-bolts for disas-
sembly ...................................................................... 42
Figure 4.7 Unscrew the power module screws on the bottom to 
disassemble the power module................................ 43










