User Manual ASMB-922I Intel® E5-2600(v2) Series Dual Processor EATX Server Board
Copyright The documentation and the software included with this product are copyrighted 2013 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
A Message to the Customer Advantech Customer Services Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech equipment is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known. Your satisfaction is our primary concern.
Declaration of Conformity FCC This device complies with the requirements in part 15 of the FCC rules: Operation is subject to the following two conditions: This device may not cause harmful interference This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Peripheral Compatibility Category Advantech PN MB CPU Vendor Part Description ASMB-922I-00A1E Advantech Support BMC module Remarks ASMB-922-00A1E Advantech Basic sku 96MPXE-2.120M20T Intel Xeon E5-2658/2.1GHz/8cores 95W(Included in the Intel embedded roadmap) 96MPXE-2.015M20T Intel Xeon E5-2620/2.0GHz/6cores 95W(Included in the Intel embedded roadmap) 96MPXE-1.820M20T Intel Xeon E5-2648L/1.8GHz/8cores 70W(Included in the Intel embedded roadmap) TBD Intel Xeon E5-2660/2.
Initial Inspection Before installing motherboard, please make sure that the following materials have been shipped: 1 x ASMB-922I EATX motherboard 1 x ASMB-922I Startup Manual 1 x Driver CD (user manual is included) 2 x Serial ATA HDD data cables 1 x I/O port bracket 2 x SATA power cable 1 x Warranty card If any of these items are missing or damaged, contact distributor or sales representative immediately. We have carefully inspected the ASMB-922I mechanically and electrically before shipment.
Contents Chapter 1 Overview...............................................1 1.1 1.2 1.3 1.6 1.7 1.8 Introduction ............................................................................................... 2 Features .................................................................................................... 2 Specifications ............................................................................................ 3 Table 1.1: Specifications ................................................
Chapter 3.1 3.2 Introduction ............................................................................................. 34 BIOS Setup ............................................................................................. 35 3.2.1 Main Menu .................................................................................. 35 3.2.2 Advanced BIOS Features Setup................................................. 35 3.2.3 Chipset..........................................................................
B.6 B.7 B.8 B.9 B.10 B.11 B.12 B.13 B.14 B.15 B.16 B.17 System Fan Power Connector (SYSFAN0~2) ........................................ 88 Table B.6: Fan Power Connector (SYSFAN0/SYSFAN1/ SYSFAN2) ................................................................ 88 Power LED (JFP3) .................................................................................. 88 Table B.7: Power LED (JFP1).................................................... 88 External Speaker Connector (JFP2) ........................
ASMB-922I User Manual x
Chapter 1 Overview 1
1.1 Introduction The ASMB-922I serverboard is the most advanced Intel Xeon E5-2600 (v2) series board for server-grade IPC applications that require high-performance computing power & multi-expansion slots. This serverboard supports Intel Xeon E5-2600(v2) series processor and DDR3 1066/1333/1600 MHz memory up to 128 GB. ASMB-922I provides 3*PCI-E x16 slot(x16 link) & 1*PCI-E x8 slot(x8 link) & 1*PME slots.
Table 1.1: Specifications Processor CPU Xeon processor supports DDR3 memory bus Total 8 memory slots provided Supports up to 128 GB memory 4 channels per processor, 1 memory slot per channel System Memory Memory Capacity Memory Type Supports DDR3 1066/1333/1600 MHz ECC Registered / ECC Unbuffered / Non-ECC Unbuffered Modules. DIMM Sizes Each memory slot supports 1GB, 2GB, 4GB, 8GB and 16GB memory modules Memory Voltage 1.35V & 1.
Table 1.1: Specifications Power Connector System Power 1 x 24-pin SSI EPS 12 V power connector (Input 12 V, 5 V, 3.
Connectors on the ASMB-922I are linked to external devices such as hard disk drives. In addition, ASMB-922I has a number of jumpers that are used to configure system for specific applications. The tables below list the functions of each jumper and connector. Later sections in this chapter give instructions for setting jumpers. Chapter 2 gives instructions for connecting external devices to ASMB-922I. Chapter 1 1.4 Board Layout, Jumpers and Connectors Overview Figure 1.
ASMB-922I-00A1E ASMB-922-00A1E Figure 1.2 Rear I/O Table 1.2: Onboard LAN LED Color Definition 10/100/1000 Mbps LAN Link/Activity LED Scheme LAN1 & LAN2 BMC LAN1 Left LED Right LED Left LED Right LED 10 Mbps Link Active Off Off Green Blinking green Amber Amber Blinking green 100 Mbps Link Active Amber Amber Green Blinking green Amber Amber Blinking green 1000 Mbps Link Active Green Green Green Blinking green - - Off Off Off Off No Link Table 1.
2 1 3 Keep CMOS data/ Disable ME update/ 2 3 Clear CMOS data/ Enable ME update/ Label Function ATX12V1 SSI EPS 12 V auxiliary power connector (for CPU0) and memory ATX12V2 SSI EPS 12 V auxiliary power connector (for CPU1) and memory ATXPWR1 SSI EPS 24-pin main power connector (for system) COM2 Serial port: RS-232 CPU0 Intel LGA2011 CPU0 socket CPU1 Intel LGA2011 CPU1 socket CPUFAN0 CPU0 fan connector (4-pin) CPUFAN1 CPU1 fan connector (4-pin) DIMMA0 Channel A DIMM0 of CPU0 DIMMB0
Table 1.4: Connectors USB89 USB port 8, 9 USB10 USB port 10 (Type-A) VOLT1 For Advantech alarm board usage PMBUS1 Power supply SMBbus I2C Header SATA_SGPIO_1 Support Serial_Link interface for onboard SATA connections GPIO1 GPIO function for customize usage SMBUS1 For Advantech chassis usage KBMS2 For additional keyboard/mouse Table 1.
ASMB-922I has eight 240-pin memory slots for DDR3 1066/1333/1600 MHz memory modules with maximum capacity of 128 GB (Maximum 16 GB for each DIMM). ASMB-922I supports registered DIMMs or unbuffered DIMM with ECC / Non-ECC memory module. Chapter 1 1.6 System Memory 1.
Step 2 Slowly slide the DIMM module along the plastic guides on both ends of the socket, Step 3 Press the DIMM module right down into the socket, until you hear a click. This is when the two handles have automatically locked the memory module into the correct position of the DIMM socket. Step 4 Finished.
The ASMB-922I is designed for Intel E5-2600 series Xeon processor. Step 1 Press the first lever and move it sideways slightly until it is released from the retention tab. Chapter 1 1.8 Processor Installation Overview Step 2 Press the other lever and move it sideways slightly until it is also released from the retention tab.
Step 3 Lift the load plate. Step 4 Position the CPU over the socket ensuring that the triangle mark on the CPU lines up with the triangle mark on the motherboard. CPU Triangle mark Step 5 Remove protective plastic cover.
Chapter 1 Step 6 Close the load plate over the CPU. Step 8 Finished. 13 ASMB-922I User Manual Overview Step 7 Push down both levers and insert them under the retention tabs ensuring the edge of the load plate is fixed securely by both levers.
ASMB-922I User Manual 14
Chapter 2 Connections 2
2.1 Introduction You can access most of the connectors from the top of the board as it is being installed in the chassis. If you have a number of cards installed, you may need to partially remove a card to make all the connections. 2.2 USB Ports and LAN Ports (USB0~USB11/LAN1/ LAN2/IPMI_LAN1) The USB ports comply with USB 2.0 & 3.0. Transmission rates could be up to 480 Mbps (USB 2.0) / 5Gbps (USB 3.0) and fuse protection are supported. The USB interface can be disabled in the system BIOS setup.
The ASMB-922I includes a VGA interface that can drive conventional CRT and LCD displays. Chapter 2 2.3 VGA Connector Connections 2.4 Serial Ports (COM1/COM2) The ASMB-922I offers 2 serial ports (One on the rear panel and one onboard).
2.5 PS2 Keyboard and Mouse Connectors (KBMS1/ KBMS2) Two 6-pin mini-DIN connectors (KBMS1) on the rear panel of the motherboard provide PS/2 keyboard and mouse connections. KBMS2 connector is for additional keyboard & mouse device usage. KBMS1 KBMS2 2.6 CPU Fan Connector (CPU FAN0/FAN1) If a fan is used, this connector supports cooling fans that draw up to 500 mA (6 W).
CPU FAN0 CPU FAN1 1 GND GND 2 +12V +12V 3 CPU0_TACH CPU1_TACH 4 CPU0_PWM CPU1_PWM Table 2.2: SYS FAN Pin Definition SYS FAN0 SYS FAN1 SYS FAN2 1 GND GND GND 2 +12V +12V +12V 3 FAN0_TACH FAN1_TACH FAN2_TACH 4 FAN0_PWM FAN1_PWM FAN2_PWM 19 ASMB-922I User Manual Connections 2.7 System Fan Connector (SYS FAN0/FAN1/FAN2) Chapter 2 Table 2.
2.8 Front Panel Connector (JFP1) There are several external switches and LEDs to monitor and control the ASMB-922I. 2.8.1 Power LED (JFP3) JFP3 pin 1 and pin 3 are for the power LED. Refer to Appendix B for detailed information on the pin assignments. If an ATX power supply is used, the system’s power LED status will be as indicated as follows. Table 2.
4 7 Chapter 2 1 10 + - 2.8.3 HDD LED Connector (JFP1 Pins 2 & 5) You can connect an LED to connector JFP1 to indicate when the HDD is active. 2 5 2.8.4 Reset Connector (JFP1 Pins 9 & 12) Many computer cases offer the convenience of a reset button. 9 12 2.8.5 SNMP Connector(JFP1 Pins 8 & 11) SNMP connector could apply with “SAB-2000”remote control board to monitor the situation of ASMB-922I through super IO chip. 8 11 (Data) (CLK) 2.8.
1 2 2.
Chapter 2 2.10 Front Panel LAN Indicator Connector (LANLED1) Connections 1 LAN1_LED0_ACT 2 LAN2_LED1_ACT 3 VCC3_LAN1LED 4 VCC3_LAN2LED 5 LAN1_LED1_1000M 6 LAN2_LED2_1000 7 LAN1_LED2_100M 8 LAN2_LED0_100 9 VCC3 10 NC 2.11 Serial ATA Interface (SATA0 ~ 5) ASMB-922I features two serial ATA III (SATA 0 & SATA 1) interfaces (up to 600 MB/s) and four serial ATA II (SATA 2 ~ SATA 5) interfaces (up to 300 MB/s) which ease cabling to hard drives with thin and long cables.
ASMB-922I User Manual 24
Chapter 2 2.12 PCIe & PCI Expansion Slots The ASMB-922I provides several expansion slots. Connections Slot Length Link PCI-E Generation PCIe link provide from SLOT7 PCI-E x16 PCI-E x16 3 CPU1 SLOT6 PCI-E x16 PCI-E x16 3 CPU0 SLOT5 PCI-E x16 PCI-E x16 3 CPU1 SLOT4 PCI-E x8 PCI-E x8 3 CPU0 PME slot PCI-E x16 PCI-E x16 1/2/3* CPU0 Note! The PCIe link speed depends on what type of PME card you use.
2.13 Auxiliary Power Connector (ATXPWR1/ ATX12V1/ATX12V2) Note! 1. 2. Please use a power supply which is of SSI type; minimum output should be at least 800 W. ATXPWR1 & ATX12V1 & ATX12V2 sockets should be all connected with power supply, otherwise ASMB-922I will not boot up normally. 2.
+5 V_AUD 2 GND 3 ACZ_SYNC 4 ACZ_BITCLK 5 ACZ_SDOUT 6 ACZ_SDIN0 7 ACZ_SDIN1 8 ACZ_RST# 9 +AC_12V 10 GND 11 GND 12 NC 1 CLK_33M_TPM 2 LPC_AD1 3 PLTRST_LPC 4 LPC_AD0 5 LPC_FRAME 6 +3.3 V 7 LPC_AD3 8 GND 9 LPC_AD2 10 SMB_SCL_LPC 11 SERIRQ_PCH 12 SMB_SDA_LPC 13 +5V_AUX 14 +5V 27 ASMB-922I User Manual Connections 2.
2.16 Clear CMOS Connector (JCMOS1) Setting jumper from pin 1-2 to pin 2-3,then back to pin 1-2 to reset CMOS data. JCMOS1 JME1 1 SRTC_RST_PCH NC 2 RTC_RST_PCH HDA_SDOUT_PCH 3 GND 3.3V 2.
SMB_SCL_PM 2 SMB_SDA_PM 3 SMB_ALT_PM 4 GND 5 +3.3V Chapter 2 1 1 +3.3V_AUX 2 SMB_SCL_FRU 3 SMB_SDA_FRU 4 GND 29 ASMB-922I User Manual Connections 2.
2.19 IPMI Module Connector (BMC1) IPMI1 This connector only fit to ASMB-BMC-00A1E and only exist in ASMB-922I sku.
Chapter 2 2.20 VOLT1 Connector Connections VOLT1 connects to the alarm board of Advantech chassis. These alarm boards give warnings if a power supply or fan fails, if the chassis overheats, or if the backplane malfunctions. 1 5VSB 5 +5V 2 GND 6 +3.
2.
Chapter 3 AMI BIOS 3
3.1 Introduction AMI BIOS has been integrated into many, many motherboards for over two decades. In the past, people often referred to the AMI BIOS setup menu as BIOS, BIOS setup or CMOS setup. With the AMI BIOS Setup program, you can modify BIOS settings and control the special features of your computer. The Setup program uses a number of menus for making changes and turning the special features on or off. This chapter describes the basic navigation of the ASMB-922I setup screens.
3.2.1 Main Menu Press during bootup to enter AMI BIOS CMOS Setup Utility; the Main Menu will appear on the screen. Use arrow keys to select among the items and press to accept or enter the sub-menu. Chapter 3 3.2 BIOS Setup AMI BIOS The Main BIOS setup screen has two main frames. The left frame displays all the options that can be configured. Grayed-out options cannot be configured; options in blue can be. The right frame displays the key legend.
3.2.2.
Above 4G Decoding Enables or disables 64-bit capability. Devices to be decoded in above 4G address space (Only if system supports 64bit PCI decoding). PCI Latency Timer Value in units of PCI clocks for PCI device latency timer register. VGA Palette Snoop Enables or disables VGA palette register snooping. Chapter 3 3.2.2.2 ACPI Settings AMI BIOS Enable Hibernation "Enable or disable" Hibernation. ACPI Sleep State Specifies the ACPI sleep state when the system enters standby.
3.2.2.3 Trusted Computing Security Device Support Enables or disables BIOS support for security device. Purchase Advantech LPC TPM module to enable TPM function. P/N: PCATPM-00A1E.
Chapter 3 3.2.2.4 WHEA Support AMI BIOS WHEA Support “Enable or disable” Windows Hardware Error Architecture.
3.2.2.
Intel® Virtualization Technology This feature is used to enable or disable the Intel Virtualization Technology (IVT) extension. It allows multiple operating systems to run simultaneously on the same system. It does this by creating virtual machines, each running its own x86 operating system. 41 ASMB-922I User Manual AMI BIOS Hyper-threading Enable or disable Intel Hyper Threading technology.
CPU Power Management Configuration Power technology default is “Energy Efficient”. User can set “EIST”, “P-STATE”, “C3”, “C6”, “Package C State limit” under “Custom” Mode.
Chapter 3 3.2.2.6 SATA Configuration SATA Mode Configured as IDE/RAID/AHCI or Disabled. IDE Mode AMI BIOS – Serial-ATA Controller 0 This item appears only when SATA Mode item set to [IDE Mode]. Set to [Enhanced] to support two SATA 6.0 Gb/s and four SATA 3.0 Gb/s devices. Set to [Compatible] when using Windows 98/NT/2000/MS-DOS. Up to four SATA devices are supported by controller 0 and two SATA devices are supported by controller 1 when under these operating systems.
AHCI Mode Set to [AHCI Mode] to have the SATA hard disk drives use the AHCI (Advanced Host Controller Interface). The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increase storage performance on random workloads by allowing the drive to internally optimize the order of commands. RAID Mode Set to [RAID Mode] to create a RAID configuration from the SATA hard disk drives.
Chapter 3 3.2.2.7 Intel TXT(LT-SX) Configuration This item shows Intel trusted execution technology configuration. AMI BIOS 3.2.2.8 USB Configuration Legacy USB Support This is for supporting USB device under a legacy OS such as DOS.
plugged into the computer and enable USB legacy mode when a USB device is plugged and disable USB legacy mode when no USB device is attached. USB3.0 support Enable/disable USB3.0(XHCI) controller support. XHCI Hand-off This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change should be claimed by XHCI driver. EHCI Hand-off This is a workaround for OSes without EHCI hand-off support. The EHCI ownership change should be claimed by EHCI driver.
Chapter 3 Serial Port 0 Configuration AMI BIOS Serial Port “Enable” or “Disable” Serial Port 0. Change Settings To select an optimal setting for serial port 0.
Serial Port “Enable” or “Disable” Serial Port 1. Change Settings To select an optimal setting for serial port 1. 3.2.2.10 H/W Monitor Case Open Warning Enable/Disable the Chassis Intrusion monitoring function. When enabled and the case is opened, the warning message will show in POST screen. Watchdog Timer Enable and Disable the watchdog timer function. CPU Warning Temperature Set the CPU warning temperature threshold.
Chapter 3 AMI BIOS 3.2.2.11 Serial Port Console Redirection Console Redirection To “Enable or disable” console redirection feature.
Console Redirection Settings Terminal Type Select a terminal type to be used for console redirection. Options available: VT100/VT100+/ANSI /VT-UTF8. Bits Per Second Select the baud rate for console redirection. Options available: 9600/19200/57600/115200. Parity A parity bit can be sent with the data bits to detect some transmission errors. Even: parity bit is 0 if the number of 1's in the data bits is even. Odd: parity bit is 0 if number of 1's the data bits is odd. Mark: parity bit is always 1.
Out-of-Band Mgmt Port To select the com port user would like to set for having console redirection feature. Terminal Type Set as "VT100", "VT100+", "VT-UTF8", or "ANSI". "VT-UTF8" is the default setting. Bits Per Second To select serial port transmission. Speed must be matched on the other side. It can be set as "9600", "19200", "57600", or "115200". "115200" is the default setting. Flow Control Flow control can prevent data loss from buffer overflow.
3.2.3 Chipset 3.2.3.1 North Bridge Compatibility RID Support for Compatibility Revision ID (CRID). Functionality mentioned in BIOS spec. Numa Enable/Disable non uniform memory access (NUMA).
Patrol Scrub Enable/Disable patrol scrub feature. Demand Scrub Enable/Disable demand scrub feature. Data Scrambling Enable/Disable data scrambling. Device Tagging Enable/Disable device tagging. Chapter 3 AMI BIOS IOH Configuration Intel I/OAT Enable/Disable Intel I/O Acceleration Technology function. DCA Support Enable/Disable Direct Cache Access Support VGA Priority Determines priority between onboard and 1st off-board video device found.
x8x4x4 x8x8 x16 PORT 2A Link Speed Select target link speed as Gen1, Gen2, Gen3. IOU3 - PCIe Port(PME Board) This item is auto selected by BIOS. PORT 3A Link Speed Select Target Link Speed as Gen1, Gen2, Gen3. IOH1 PCIe port bifurcation control IOU2 - PCIe port(PCIEX16_SLOT7) Functions visible based on this setting : x4x4x4x4 x4x4x8 x8x4x4 x8x8 x16 PORT 2A Link Speed Select Target Link Speed as Gen1, Gen2, Gen3.
Chapter 3 AMI BIOS Intel VT-d Enable/Disable Intel Virtualization Technology for Directed I/O. QPI Configuration Isoc Enable/Disable Isoc QPI Link Speed Mode Select the QPI link speed as either the Fast mode or Slow Mode.
QPI Link Frequency Select Allows for selecting the QPI Link frequency.
Chapter 3 3.2.3.2 South Bridge AMI BIOS PCH Compatibility RID Enable/Disable PCH Compatibility Revision ID (CRID) Functionality. SMBus Controller Enable/Disable SMBus controller. PCIE Wake Enable or disable PCIE to wake the system from S5. Restore AC Power Loss Specify what state to go to when power is re-applied after a power failure (G3 state). SLP_S4 Assertion Stretch Enable Enable/Disable SLP_S4 Assertion Stretch function.
LAN Configuration LAN1 Controller Enable/Disable Intel I210 Controller support. Wake on LAN From S5 Enable/Disable Intel 82579LM controller wake up from S5 support. LAN1 PXE Oprom Enable/Disable Boot option for Intel I210 controller. LAN2 Controller Enable/Disable Intel 82579LM Controller support. LAN2 PXE Oprom Enable/Disable Boot option for Intel 82579LM controller.
Chapter 3 USB Configuration AMI BIOS All USB Devices Enable/Disable all USB devices. EHCI Controller 1 Enable/Disable USB 2.0 (EHCI) support. EHCI Controller 2 Enable/Disable USB 2.0 (EHCI) support. USB Port 0 ~ 10 Enable/Disable USB 2.0 port 0 ~ 10.
3.2.3.3 ME Subsystem 3.2.
BMC Support Enable/Disable interfaces to communicate with BMC Wait for BMC If enabled, motherboard will wait 30 ~ 60 seconds until BMC module boots up completely. After that, the normal BIOS post screen will be displayed. If disabled, motherboard will not wait for BMC module's response. Wait for BMC counter Wait for BMC counter for initialize host to BMC interfaces. The MB beep per 5 seconds to check it. 3.2.4.
3.2.5 Boot Setup Prompt Timeout Number of seconds to wait for setup activation key. 16(0x10) means indefinite waiting. Bootup NumLock State Select the keyboard NumLock state. Quiet Boot Enable/Disable quiet boot option. INT19 Trap Response BIOS reaction on INT19 trapping by option ROM: – Immediate - execute the trap right away. – Postponed - execute the trap during legacy boot. Boot Option Sets the system boot priorities.
Chapter 3 3.2.6 Security AMI BIOS 3.2.
Save Changes and Exit Exit system setup after saving the changes. Discard Changes and Exit Exit system setup without saving any changes. Save Changes and Reset Reset the system after saving changes. Discard Changes and Reset Reset system setup without saving any changes. Save Changes Save changes done so far to any of the setup options. Discard Changes Discard changes done so far to any of the setup options. Restore Defaults Restore/Load default values for all the setup options.
Chapter 4 Chipset Software Installation Utility 4
4.1 Before Beginning To facilitate the installation of the enhanced display drivers and utility software, read the instructions in this chapter carefully. The drivers for the ASMB-922I are located on the software installation CD. Before beginning, it is important to note that most display drivers need to have the relevant software application already installed on the system prior to installing the enhanced display drivers.
1. Insert the driver CD into your system's CD-ROM drive. When the folder is displayed, move the mouse cursor over the folder "01_Intel INF". Find the executable in this folder, click to install the driver. Chapter 4 4.
2. Click setup to execute program.
Chapter 5 VGA Setup 5
5.1 Introduction Install the ASPEED VGA driver to enable this function, which includes the following features: 32bit 2D graphics engine on board for normal use. 64MB Ram for this chip, the highest resolution is 1920x1200. 5.2 Windows Series Driver Setup Insert the driver CD into your system's CD-ROM drive. When the folder is displayed, navigate to the "02_Graphic chip" folder and click the executable file to complete the installation of the drivers for OS that you need. Note! 1. 2.
Chapter 6 6 LAN Configuration & USB 3.
6.1 LAN Configuration 6.1.1 Introduction The ASMB-922I has two Gigabit Ethernet LAN connections via dedicated PCI Express x1 lanes: GbE LAN1 - Intel I210; GbE LAN2 - Intel 82579LM. They offer bandwidth of up to 500 MB/sec, eliminating the bottleneck of network data flow and incorporating Gigabit Ethernet at 1000 Mbps. 6.1.
6.2.1 Introduction ASMB-922I offers two USB 3.0 ports in rear side. The USB 3.0 could provide the bandwidth up to 500MB/s to shorter the time for data transmission. 6.2.2 Windows series driver setup 6.3 Audio 6.3.1 Introduction ASMB-922 offers an audio header to apply with "PCA-AUDIO-HDA1E" audio card. Select folder "06_Audio module" then click the proper".exe"driver file for the installation. 73 ASMB-922I User Manual LAN Configuration & USB 3.0 Insert the driver CD into your system's CD-ROM drive.
6.4 AHCI & SATA RAID Intel C602J PCH chip offers SATA RAID with RAID 0, 1, 10, 5 under Windows operating system. But there are some limitation & remark shown as below: OS AHCI RAID Remark Windows XP 32bit Not support Not support Driver no support Windows XP 64bit Support Not support 1.AHCI needed to install HDD without 4K alignment Windows server 2003 32bit Support Support under 1.AHCI needed to install HDD special condi- without 4K alignment tion 2.
Please visit the Microsoft website address as below for hotfix file download: http://support.microsoft.com/kb/932755/en-us Chapter 6 Note! LAN Configuration & USB 3.
ASMB-922I User Manual 76
Appendix A A Programming the Watchdog Timer
The ASMB-922I’s watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function within the programmed period. This section describes the operation of the watchdog timer and how to program it. A.1 Watchdog Timer Overview The watchdog timer is built in to the super I/O controller NCT6776D.
Appendix A Programming the Watchdog Timer Unlock NCT6776D Select watchdog timer register Enable the watchdog timer function Use the watchdog timer function Lock NCT6776D 79 ASMB-922I User Manual
Table A.1: Watchdog Timer Registers Address of Read/ register (2E) Write Value (2F) & description 87 (hex) - Write this address to I/O address port 2E (hex) twice to unlock the NCT6776D 07 (hex) write Write 08 (hex) to select register of watchdog timer. 30 (hex) write Write 01 (hex) to enable the function of the watchdog timer. Disabled is set as default. write Set seconds or minutes as units for the timer. Write 0 to bit 3: set seconds as counting unit. [default].
81 ASMB-922I User Manual Appendix A Programming the Watchdog Timer Dec dx ; Set second as counting unit Mov al,0f5h Out dx,al Inc dx In al,dx And al,not 08h Out dx,al ;----------------------------------------------------------Dec dx ; Set timeout interval as 10 seconds and start counting Mov al,0f6h Out dx,al Inc dx Mov al,10; 10 minutes Out dx,al ;----------------------------------------------------------Dec dx ; lock NCT6776D Mov al,0aah Out dx,al Enable watchdog timer and set 5 minutes as the timeout
Out dx,al ;----------------------------------------------------------Dec dx ; Set timeout interval as 5 minutes and start counting Mov al,0f6h Out dx,al Inc dx Mov al,5; 5 minutes Out dx,al ;----------------------------------------------------------Dec dx ; lock NCT6776D Mov al,0aah Out dx,al Enable watchdog timer to be reset by mouse ;----------------------------------------------------------Mov dx,2eh ; unlock NCT6776D Mov al,87h Out dx,al Out dx,al ;-------------------------------------------------------
83 ASMB-922I User Manual Appendix A Programming the Watchdog Timer ;----------------------------------------------------------Mov dx,2eh ; unlock NCT6776D Mov al,87h Out dx,al Out dx,al ;----------------------------------------------------------Mov al,07h ; Select registers of watchdog timer Out dx,al Inc dx Mov al,08h Out dx,al ;----------------------------------------------------------Dec dx ; Enable the function of watchdog timer Mov al,30h Out dx,al Inc dx Mov al,01h Out dx,al ;----------------------
Out dx,al Inc dx In al,dx Or al,01h Out dx,al ;----------------------------------------------------------Dec dx ; Generate a time-out signal Mov al,0f7h Out dx,al ;Write 1 to bit 5 of F7 register Inc dx In al,dx Or al,20h Out dx,al ;----------------------------------------------------------Dec dx ; lock NCT6776D Mov al,0aah Out dx,al ASMB-922I User Manual 84
Appendix B B I/O Pin Assignments
B.1 USB Header (USB23/45/67/89) 2 10 1 USB23 USB45 USB67 USB89 Table B.1: USB Header (USB23,USB45,USB67,USB89) Pin Signal Pin Signal 1 USB_VCC5 2 USB_VCC5 3 USB_D- 4 USB_D- 5 USB_D+ 6 USB_D+ 7 GND 8 GND 9 Key 10 N/C B.2 VGA Connector (VGA1) 5 1 10 6 15 11 Table B.
6 9 12 Table B.3: RS-232 Interface (COM2) Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI B.4 PS/2 Keyboard and Mouse Connector (KBMS1) Table B.4: Keyboard and Mouse Connector (KBMS1) Pin Signal 1 KB DATA 2 N/C 3 GND 4 KB VCC 5 KB CLK 6 N/C 7 M_DATA 8 N/C 9 GND 10 M_VCC 11 M_CLK 12 N/C 87 ASMB-922I User Manual Appendix B I/O Pin Assignments B.
B.5 External Keyboard Connector (KBMS2) Table B.5: External Keyboard Connector (KBMS2) Pin Signal 1 KB CLK 2 KB DATA 3 MS DATA 4 GND 5 VCC 6 MS CLK B.6 System Fan Power Connector (SYSFAN0~2) Table B.6: Fan Power Connector (SYSFAN0/SYSFAN1/SYSFAN2) Pin Signal 1 GND 2 +12 V 3 DETECT 4 PWM B.7 Power LED (JFP3) 1 2 3 Table B.7: Power LED (JFP1) Pin Function 1 LED power (3.
1 4 7 10 Table B.8: External Speaker Connector (JFP2) Pin Function 1 SPK+ 4 NC 7 BZ- 10 SPK- B.9 Reset Connector (JFP1) 9 12 Table B.9: Reset Connector (JFP1) Pin Signal 9 RESET 12 GND B.10 HDD LED Connector (JFP1) 2 5 Table B.10: HDD LED Connector (JFP1) Pin Signal 2 HDD_LED+ 5 HDD_LED- 89 ASMB-922I User Manual Appendix B I/O Pin Assignments B.
B.11 ATX Soft Power Switch (JFP1) 3 6 Table B.11: ATX Soft Power Switch (JFP1) Pin Signal 3 PWR-BTN 6 GND B.12 Front panel SMBus Connector (SMBUS1) 1 +3.3V_AUX 2 SMB_SCL_FRU 3 SMB_SDA_FRU 4 GND B.13 USB/LAN Ports (LAN1_USB01 and LAN2_USB23) LAN1_USB01 LAN2_USB23 Table B.
Pin Signal Pin Signal 1 MID0+ 5 MID2+ 2 MID0- 6 MID2+ 3 MID1+ 7 MID3+ 4 MID1- 8 MID3+ B.14 Audio Connector (AUDIO1) Table B.14: Front Panel Audio Connector (FPAUD1) Pin Signal Pin Signal 1 ACZ_VCC 2 GND 3 ACZ_SYNC 4 ACZ_BITCLK 5 ACZ_SDOUT 6 ACZ_SDIN0 7 ACZ_SDIN1 8 ACZ_RST 9 ACZ_12V 10 GND 11 GND 12 N/C B.15 8-pin Alarm Board Connector (VOLT1) 1 8 Table B.15: 8-pin Alarm Board Connector (VOLT1) Pin Signal Pin Signal 1 5VSB 5 +5V 2 GND 6 +3.
B.16 Case Open Connector (JCASE1) 1 2 Table B.16: Case Open Connector (JFP1) Pin Signal 1 CASEOP 2 GND B.17 Front Panel LAN LED Connector (LANLED1) Table B.
Appendix B I/O Pin Assignments ASMB-922I User Manual 93
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
