FPM-3060G Series Flat Panel Monitor with 6" Color TFT/LCD Display User Manual
Copyright Notice This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (1 year) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for one year from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Packing List Before installing your equipment, make sure that the following materials have been received: • FPM-3060G Series flat panel monitor • Accessory pack, including: - AC/DC adapter - AC/DC power adapter bracket - Video signal cable, 1.8m - Fixed panel-mounted bracket x 6 pcs - Screw Bags (M4x25 mm screws x 6 pcs) - DC in Power Cord bracket x 1 piece - RS-232 cable, 1.8m (FPM-3060G-R only)or USB cable, 1.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE EQUIPMENT. The sound pressure level at the operator's position according to IEC 7041:1982 is no more than 70dB(A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. Wichtige Sicherheishinweise 1.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden. 14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu überprüfen: a - Netzkabel oder Netzstecker sind beschädigt. b - Flüssigkeit ist in das Gerät eingedrungen. c - Das Gerät war Feuchtigkeit ausgesetzt.
Contents Chapter 1 Introduction ..................................................... 2 1.1 1.2 1.3 1.4 1.5 1.6 Chapter Introduction ....................................................................... 2 Specifications .................................................................... 2 LCD Specifications ........................................................... 3 Power Adapter Specifications ........................................... 3 Connectors..................................................
FPM-3060G Series User Manual x
CHAPTER 1 2 Introduction This chapter includes: • Introduction • Specifications • LCD Specification • Power Consumption • Connectors • Dimensions
Chapter 1 Introduction 1.1 Introduction Advantech's FPM-3060G Series consists of 6" color TFT LCD flat panel monitors built specifically for industrial applications. With the optional touchscreen, the FPM-3060G Series is an user-friendly system control interface. In addition to its usual application as an LCD panel monitor, the FPM3060G Series comes standard with Direct VGA control signal input, making it compatible with industrial PCs and workstations.
• Power Consumption: 2.2A(max.) @12V +/- 10% Touchscreen (Optional) • Type: 4 wire, analog resistive • Resolution: 1024 x 1024 • Light Transmission: 75% (Gouge Hardness is greater than 4H per ASTM D3363-92 for HCC01, HCG10 and HCG12) • Controller: RS-232 interface (for FPM-3060G-R version) or USB 1.
1.5 Connectors The following connectors are on the bottom of the FPM-3060G Series: VGA Port (DB15) This DB-15 connector can be connected to the system via the external 15pin video signal cable. RS-232 Touchscreen Connector (DB9) (with FPM-3060G-R) This connector will only be present if a touchscreen is installed. It must be connected to the RS-232 port of the PC. The touchscreen cable is included with all orders that include the touchscreen option.
1.6 Dimensions Figure 1.
FPM-3060G Series User Manual 6
CHAPTER 2 2 System Setup • Mounting the Monitor • Wall / Panel / VESA Arm Mounting • Mounting with MBPC-200 or UNO2000 series
Chapter 2 System Setup 2.1 Mounting FPM-3060G The FPM-3060G Series can be flexibly mounted. The versatility of the FPM-3060G mounts enable it to be mounted almost anywhere. 2.1.1 Wall Mounting Please refer to figure 2.1 and follow the steps below to install FPM3060G on a wall. The wall mounting kit is optional. (P/N: FPM-3060VESA-MT) 1. Screw the mounting kit with FPM-3060G. 2. Screw three screws on the wall with the dimensions used in Figure 2.1. 3. Hook FPM-3060G on the screws Figure 2.
2.1.2 Panel Mounting Refer to figure 2.2 and follow the instructions below to install in a panel. 1. Place six panel-mounting brackets on FPM-3060G (2 on the top, 2 on the bottom, 1 on the left, and 1 on the right). 2. Fasten the six panel-mounting brackets with screws. 3. Mount FPM-3060G on the panel by the screws on the six panelmounted brackets. Please note that the panel thickness must be below 6 mm. Figure 2.2: Panel Mounting 2.1.
2.2 Power Adapter The power adapter bracket is attached to the rear of FPM-3060G. Attach/ detach the power bracket at the rear side of the monitor by screwing/ unscrewing the four screws. 2.3 Mounted with MBPC-200 or UNO-2000 series FPM-3060G can easily be combined with products in the MBPC-200 or UNO-2000 series. 2.3.1 Mounted with MBPC-200 series product FPM-3060G can be directly mounted with MBPC-200 series products with four M3 screws (not included). 2.3.
A APPENDIX 2 Display Timing Mode and OSD
Appendix A Display Timing Mode & OSD A.1 Supported Input Timing Modes The different frequencies below are already programmed in this module, and the synchronous signal inputs are automatically recognized. Table A.1: Supported Input Formats Vertical Frequencies Resolution 60 Hz 70 Hz 72 Hz 75 Hz 640 x 480 Yes Yes Yes Yes Note 1: Even if the preset timing is entered, some adjustment of functions such as Horizontal period, CLK-delay and display position, are required.
A.2 Keypad Interface AUTO Press this button to execute auto-adjustment process. SEL Press to show the OSD screen or select an item to change its setting. Press to move between items or increase/decrease item setting. EXIT Press to close the selected item or the whole OSD screen. ON/OFF Press the ON/OFF button to turn FPM-3060G’s backlight on and off. When power is off, the power indicator will be blinking. A.
A.4 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out.
APPENDIX B 2 Touchscreen This appendix contains information on the touchscreen, and its installation.
Appendix B Touchscreen B.1 Introduction FPM-3060G Series’ optional touchscreen uses advanced Fujitsu 4-wire resistive technology. The touchscreen is specially designed for tough industrial environments, and has been approved to FCC Class B standards. B.2 Touchscreen Specifications Electrical • Operating voltage: 5 V (typical) • Linearity: <1.5% full scale linearity error in either direction.
B.3 Installing Driver for Windows 2000/XP The touchscreen has drivers for Windows 2000 and Windows XP. You should read the instructions in this chapter carefully before you attempt installation. Note 1: The following windows illustrations are examples only. You must follow the flow chart instructions and pay attention to the instructions which then appear on your screen.
3. For FPM-3060G-R, please choose 1. Non Plug and Play Device. Then Click "OK". 4. The driver installation will complete. 5. Select the COM port on the PC that the touch screen is connected to. Then click Ok.
B.4 Touch Panel Device Driver Settings For further details on touch driver settings, calibration and setup of rotation coordinates, please see the Fujitsu driver manual file on the CDROM. File name: Fujitsu-TP-Driver.
FPM-3060G Series User Manual 20