FPM-3150G Series 15" XGA TFT LCD Industrial Monitor with VGA and DVI Inputs User Manual
Copyright Notice This document is copyrighted by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Packing List Before installing your equipment, make sure that the following materials have been received: • FPM-3150G Series flat panel monitor • Accessory pack, including: - AC/DC adapter - AC/DC power adapter bracket - DC in Power Cord Bracket x 1 piece - Video Signal Cable, 1.8m - Panel/Wall mount bracket x 2 - Panel sponge x 4 - RS-232 cable, 1.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY DAMAGE THE EQUIPMENT. The sound pressure level at the operator's position according to IEC 7041:1982 is no more than 70dB(A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. Wichtige Sicherheishinweise 1.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen. 13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet werden. 14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer qualifizierten Servicestelle zu überprüfen: a - Netzkabel oder Netzstecker sind beschädigt.
Contents Chapter 1 Introduction ..................................................... 2 1.1 1.2 1.3 1.4 1.5 1.6 Chapter Introduction ....................................................................... 2 Specifications .................................................................... 2 LCD Specification............................................................. 3 Power Consumption .......................................................... 3 Connectors..............................................
C.2.10 C.2.11 C.2.12 C.2.13 FPM-3150 User Manual Mode Information Menu .............................................. 31 Memory Recall Menu .................................................. 32 Exit Menu .................................................................... 33 Hot Keys ......................................................................
CHAPTER 1 2 Introduction This chapter includes: • Introduction • Specifications • LCD Specification • Power Consumption • Connectors • Dimensions
Chapter 1 Introduction 1.1 Introduction Advantech's FPM-3150G is a 15" color TFT LCD flat panel monitor built specifically for industrial applications. With the optional touchscreen, FPM-3150G is an excellent and user-friendly system control interface. In addition to its usual application as an LCD panel monitor, FPM-3150G comes standard with direct VGA control signal input, making it compatible with Industrial PCs and Workstations.
Touchscreen (Optional) • Type: 8 wire, analog resistive • Resolution: 1024 x 1024 • Light Transmission: >80% (Gouge Hardness is greater tahn 4H per ASTM D3363-92 for HCC01, HCG10 and HCG12 • Operating Pressure: 30 ~ 45 gram for stylus pen contact bounce < 10 ms • Controller: USB & RS-232 interface • Power Consumption: +5 V @ 200 mA • OS Support: Win 95/98/ME/2000/XP/CE/NT/Vista, Linux, MS-DOS • Life Span: 100 million activation (typical) at a single point with a 5/8" diameter silicone finger with a 350 g lo
1.5 Connectors The following connectors are situated on the left hand side of the FPM-3150G Series: VGA Port (DB-15) This DB-15 connector can be connected to the system via the external 15-pin DB-15 connector locatd on the left side of the system unit. DVI Port (DVI-D) Connected with a standard DVI connector thru I/O port of this unit. Only supports digital signals Touchscreen Connector (DB-9) (optional) This connector will be present only if a touchscreen is installed.
1.6 Dimensions Figure 1.
FPM-3150 Series User Manual 6
CHAPTER 2 Mounting • Wallmounting • Panel Mounting • Rack Mounting • Desktop Mounting • Swing Arm Mounting 2
Chapter 2 Mounting 2.1 Mounting the Monitor The FPM-3150G Series can be mounted in many different ways. The versatility of the FPM-3150G mounts enable it to be mounted on your desk or anywhere else. 2.1.1 Wall Mounting FPM-3150G can be mounted directly on a wall with panel mounting brackets. Please refer to figure 2-1 and follow the following steps to mount FPM-3150G on a wall: 1. Screw the hook and panel-mount brackets on the wall. 2. Place the FPM-3150G in the brackets. 3.
2.1.2 Panel Mounting If you need to install the FPM-3150G series in a panel, please release the mounting brackets by detaching four screws on rear side and fix them on the top and bottom with screws. Panel Mounting Brackets Figure 2.
2.1.3 Rack Mounting (Optional) If you need to install the FPM-3150G on a rack, you must order the rack mount kit for FPM-3150G (Part Number is FPM-3150G-RMKE). Attach the two rack mounting brackets on each side of FPM-3150G with 12 screws, then affix the monitor in the rack. Figure 2.
2.2 Desktop, Swing-ARM for FPM-3150G The FPM-3150G Series can be mounted in other ways. These is a desktop stand for desktop use and it can also be attached to a swing-arm bracket. 2.2.1 Desktop Stand The panel-mount bracket is attached to the rear of the FPM-3150G to become a desktop stand. (Refer to figure 2.4) Simply detach the small bracket at the top of the monitor by unscrewing the two screws. The lower bracket now becomes a desktop stand bracket.
2.2.2 Swing-ARM (VESA Compliant) FPM-3150G has been designed with support for the VESA Arm standard. Refer to figure 2.5. Detach the mounting brackets on the rear side, and attach the FPM-3150G onto the VESA ARM Mount. Figure 2.
APPENDIX A 2 Touchscreen
Appendix A Touchscreen A.1 Introduction The FPM-3150G Series optional touchscreen uses advanced 8-wire resistive technology. It provides more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments, and has been approved to FCC Class B standards. Note: RS-232 & USB touch screen interface not allow to connect into the system at the same time. A.2 Touchscreen Specifications 1. Input Method and Activation Force 1.6mm dia. Delrin stylus : 0.
4. Linearity 4.1 Linear Test Specifications Direction X: <1.5 % Direction Y: <1.5 % 4.2 Linearity Test Apply voltage (DC5V) to upper (or lower ) electrodes, output voltage Vx or Vy on the other electrodes is measured at every regular intervals. Linearity is the value of max. error voltage 5. Environment Specifications 5.1 Operating Temperature: -10 ~ + 60° C 5.2 Storage Temperature: -40 ~ +80° C 5.
A.3 Installing Driver for Windows OS The touchscreen has drivers for Windows 2000 /XP/2003/Vista. You should read the instructions in CD-ROM Disk Touchscreen section carefully before you attempt installation. The FPM-3150G-XCE, RCE need to install Penmount 6000 driver. Please find Penmount 6000 folder and install the driver into your system. Note 1: The driver manual are examples only. You must follow the flow chart instructions and pay attention to the instructions which then appear on your screen.
B APPENDIX 2 Setting Serial Data for Expansion
Appendix B Setting Serial Data for Expansion B.1 Setting Serial Data for Expansion The twelve kinds of timings below are already programmed in this module. The input synchronous signals are automatically recognized.
C APPENDIX 2 OSD Operation Keypad
Appendix C OSD Operation Keypad C.1 OSD Board Overview The OSD keypad, including six keys and a two color indicator, is designed as the OSD operation interface C.1.1 OSD Button Description Buttons Descriptions Power Turn the monitor power ON or OFF. Auto/Exit Automatically adjust the clock, phase, H-position and V-position. Exit menu. Down/Right/ Increase Activate the volume control. Move the selector to the next option. Increase the gauge value of the selected option.
C.2 OSD Key Functions Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out. TIME OUT Æ 5-6 seconds ( Can be set in OSD Manager) The default definition of input keys is shown as following: C.2.
C.2.2 Input Source Select • Generate Main Menu Select by Left and Right Button, press Menu Button for selection confirmation • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN • Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option.
4. Auto Select Input • ON Æ start from default setting and scan the inputs by following sequence from ANALOG INPUT, DIGITAL INPUT, S-VIDEO INPUT, and CVBS INPUT. • OFF Æ start from default setting C.2.
• Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option. N/A RECALL VALUE – User Define • Rec1 Æ Pressed to record 1st setting as recall value followed by current screen setting • Rec2 Æ Pressed to record 2nd setting as recall value followed by current screen setting • Recall Æ Switch the setting change by Rec1 and Rec2 while pressed C.2.
• Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option.
C.2.5 Color Temperature Menu • Generate Main Menu Select by Left and Right Button, press Menu Button for selection confirmation • Main Menu -- DISPLAY IN SCREEN • Sub-Menu – DISPLAY IN SCREEN • Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option.
C.2.
• Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option. N/A Customization setting for RGB colors C.2.
• Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option. N/A C.2.
• Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option. N/A C.2.
• Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option. N/A Auto configuration can be set in menu and also can press the without any menu indication. C.2.
• Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option. N/A C.2.
• Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option. N/A C.2.
• Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option. N/A C.2.
• Entry OSD UNLOCK MODE • Press HOT KEY, the screen will show this action first • Don’t remove the HOT KEY until the screen indicated this task is finished.
FPM-3150 Series User Manual 36
