FPM-3191G Industrial Flat Panel Monitor with 19” TFT LCD Display User Manual i
Copyright This document is copyrighted by Advantech Co., Ltd. 2005. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time. Specifications are thus subject to change without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (1 year) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for one year from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
FPM-3191G User Manual vi
Contents Chapter 1 Introduction ......................................................2 1.1 1.2 1.3 1.4 1.5 Introduction ....................................................................... 2 Specifications .................................................................... 3 LCD Specifications ........................................................... 4 Connectors......................................................................... 4 Dimensions....................................................
FPM-3191G Series User Manual viii
CHAPTER Introduction This chapter includes: • Introduction • Specifications • LCD Specification • Connectors • Dimensions 1
Chapter 1 Introduction 1.1 Introduction Advantech's FPM-3191G Series is a 19" color TFT LCD flat panel monitor built specifically for industrial applications. With the optional touchscreen, the FPM-3191G Series is an excellent and user-friendly system control interface. In addition to its usual application as an LCD panel monitor, the FPM3191G comes standard with Direct-VGA interface, which connects directly with popular PC VGA cards and also supports DVI-D, S-video and CVBS connectors.
1.
1.3 LCD Specifications • Display type: SXGA TFT LCD • Display size: 19" • Max colors: Full color (16.7 million) • Max resolution: 1280 x 1024 • Dot pitch: 0.294 x 0.294 mm • Viewing Angle: 178° (H), 178° (V) • Luminance: 300 cd/m2 • Storage Temperature: -20 ~ 60° C (-4 ~ 140 ° F) • Operating Temperature: 0 ~ 50° C (32 ° ~ 122 ° F) • Backlight Lifetime: 50,000 hrs • Contrast Ratio: 1000:1 1.
1.5 Dimensions Figure 1.1: FPM-3191G Cutout Dimensions 444 x 376 mm (17.48" x 14.
FPM-3191G User Manual 6
CHAPTER 2 System Setup This chapter includes: • Mounting the Monitor - Wall/Panel/Rack Mounting - Desktop Stand/Swing-ARM Mounting
Chapter 2 System Setup 2.1 Mounting the Monitor The FPM-3191G Series can be placed as you require. The versatility of the FPM-3191G mounts enable it to be mounted on your desk or anywhere else. 2.1.1 Wall Mounting With wall brackets, the FPM-3191G can be mounted directly to a wall. If you need to install the FPM-3191G in different ways, release the mounting brackets by detaching the four screws on the rear side. Figure 2.
2.1.2 Panel Mounting If you need to install the FPM-3191G series on a panel mount, please release the mounting brackets by detaching four screws on rear side and fix them on up and bottom side by screws. Figure 2.
2.1.3 Rack Mounting FPM-3191G series products could be directly mount to the industrial standard 19" rack. There are four screw holes on each side of the panel. Figure 2.
2.2 Desktop, Swing-ARM Mounting The FPM-3191G Series can be mounted in other ways. You can place the desktop stand for desktop use or attach it on a swing-arm bracket. 2.2.1 Desktop Stand The desktop stand brackets are attached to the rear of FPM-3191G. First loosen the screw in point C. Then unscrew the screw in point A. Pull down the bracket and use the screw from point A to fasten the bracket in point B. There should be no screws in point A and point D. Only point B and C. A B C D Figure 2.
2.2.2 Swing-ARM Detach the mounting brackets on the rear side, then attach the FPM3191G series onto the Swing-ARM mount (75mm or 100mm square bracket). Figure 2.
Appendix A Touchscreen Driver Installation
Appendix A Touchscreen Installation A.1 Introduction The FPM-3191G Series’ optional touchscreens uses advanced resistive and capacitive technology. They provide more accurate sensing capacity than other technologies. The touchscreen is specially designed for tough industrial environments, and has been approved to FCC Class B standards. When installing the capacitive touchscreen, please follow appropriate procedures for calibrating and grounding the touchscreen.
Communication Parameters • Baud Rate 9600 (default), and 19200 bps • 8 Data bits, 1 stop bit, no parity only. Interface - USB Conforms to USB Revision 1.1. If the USB is connected to the controller, the controller will communicate over the USB, and will not communicate over the serial port. The touch screen control board is never powered from the USB – it is self-powered only. Operating Modes Full AccuTouch SmartSet protocol. Emulation of E281A-4002 protocol can be selected by SmartSet command.
Mechanical Linearization: Factory linearization values are stored in the touchscreen NOVRAM, attached controller or 2D bar-code Touch Contact Requirement: 3 ms for finger input. Glass Thickness: 0.125" (±0.01") / 3.18mm (±.25mm) typical. (Glass only, not including tape, wires and solder if used) Surface Scratch Hardness: Can not be scratched using any stylus with Mohs’ rating of less than 6.5. Exceeds severe abrasion test per MIL-C-675C.
A.2 Resistive Touchscreen Driver Installation A.2.1 Hardware Touchscreen controllers must be configured for the driver prior to installation. Elo typically ships controllers in a default setup that is compatible with this driver. Controller requirements are: Serial Serial controllers must conform to these minimum requirements: • Baud rate-9600 baud.
A.2.2 Software There are many options to consider when installing the driver files. This section will explain the most common ways that the driver is installed. Consult Elo Applications Engineering for situations not covered in this section. Setup from Windows Desktop For WinXP OS please execute: CDROM: \\TouchScreen-DRV\ELOTOUCH\WinXP\SetupElo.exe For Win2000 OS please execute: CDROM: \\TouchScreen-DRV\ELOTOUCH\Win2K\SetupElo.exe Single monitor, serial controller 1.
4. Check "Auto-detect Elo devices" if your touchmonitor serial cable is connected to the computer and the serial cable supports hardware handshaking. If you connect the serial cable later, do not check the "auto-detect" box. Go to the next screen. 5. A list of all the serial ports that the system detected is shown. If you checked the auto-detect box in the previous screen, and your touchmonitor serial cable is attached to the computer, the COM port that you selected should be checked in the list.
8. When the "Setup Complete" screen appears, you may choose to run calibration the (Elo Video Alignment program, EloVA) immediately or wait until later. If you choose not to run this program now, you can run it from the Elo Control Panel application. Single monitor, USB controller 1. Run the self-extracting zip file to unzip the files, using the Run EloSetup option. 2. EloSetup will launch. Check the "Install USB Touchscreen Drivers" box. 3. Review and accept the License Agreement. 4.
Multiple monitors, serial controllers 1. Follow the general procedure for Single monitor, serial controller installation above, auto detecting or selecting all the serial ports that you will use. 2. The driver files will install. When the "Setup Complete" screen appears, you may choose to run calibration (the Elo Video Alignment program, EloVA) immediately or wait until later. If you choose not to run this program now, you can run it from the Elo Control Panel application.
Multiple monitors, serial and USB controllers 1. Run the self-extracting zip file to unzip the files, using the Run EloSetup option 2. EloSetup will launch. Check both the "Install Serial Touchscreen Drivers" and "Install USB Touchscreen Drivers" boxes. 3. Review and accept the License Agreement 4. The program will appear to proceed as a single/multiple serial controller installation but USB files will also install. 5. The driver files will install.
• Adding Additional Serial Controllers Click on the Change option from the Add/Remove programs in the Control Panel, Elo entry.
• Change Serial Port To change Serial port click on the Change option from the Add/Remove programs in the Control Panel, Elo entry.
• Adding Additional USB Controllers If there are Elo USB devices already installed, plug the USB cable from the touchmonitor into the computer and run EloVA to calibrate the touchmonitors. If there are no Elo USB devices attached to the system, click on the Change option from the Add/Remove programs in the Control Panel, Elo entry.
FPM-3191G User Manual 26
Appendix Supported Input Timing Modes B
Appendix B Supported Input Timing Modes B.1 Supported Input Timing Modes The different frequencies below are already programmed in this module, and the synchronous signal inputs are automatically recognized. Table B.
Appendix C OSD Operation Keypad
Appendix C OSD Operation Keypad C.1 OSD Operation Keypad The OSD keypad, including six keys and a two color indicator, is designed as the OSD operation interface. The six keypad functions are in Table C-1. Auto Press this button to execute auto adjustment process Sel Press to show the OSD screen or select an item to change its setting To move between items or increase or decrease setting Exit This key has two functions: 1.) To exit from the current setting in OSD function 2.
C.2 OSD Function Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out.
FPM-3191G User Manual 32
